Page 2 - I n t r o d u c t i o n
2 I n t r o d u c t i o n Gen’l (Rev. 2/5/2007) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manualar...
Page 3 - I n t r o d u c t i o n 3; TABLE OF CONTENTS
I n t r o d u c t i o n 3 29936 (Rev. 5/18/2007) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY RULES . . . . . . . ....
Page 4 - S a f e t y; SAFETY RULES
4 S a f e t y L59 Safety Rules (Rev. 9/1/2006) TRAINING Safety instructions are important! Read all a tta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To locate...
Page 5 - S a f e t y 5
S a f e t y 5 L59Safety Rules (Rev. 9/1/2006) Do not stop, start, or change directions sud- denly on slopes. Use extreme care and reduce ground speed on slopes and rough terrain. Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately u p o n s t r...
Page 6 - S a f e t y; DANGER; SAFETY & INSTRUCTIONAL DECALS
6 S a f e t y 29936 (Rev. 5/18/2007) 3 - SERIAL NUMBER PLATE 1 - 25505 ROTATING BLADES AND THROWN OBJECTS Do not put hands or feet under or into mower when engine is running. Before mowing, clear area of objects that may be thrown by blade. Keep bystanders away. Keep discharge chute and guards in pl...
Page 7 - O p e r a t i o n 7; OPERATION; NOTICE
O p e r a t i o n 7 29936 (Rev. 5/18/2007) OPERATION ■ Do not allow children or unqualified persons to operate equipment. ■ Keep bystanders away from equipment while it is in operation. ■ Stop mower and tractor immediately upon striking an obstruction. Turn off engine, removekey, inspect and repair ...
Page 8 - O p e r a t i o n
8 O p e r a t i o n 29936 (Rev. 5/18/2007) Figure 1. Attitude Adjustment NOTICE ■ Improper belt alignment or tension can cause premature belt failure. LUBRICATION Grease caster pivot and wheel every 8 hours of opera-tion. There are grease fittings on each of the threeblade spindles. These are access...
Page 9 - O p e r a t i o n 9
O p e r a t i o n 9 29936 (Rev. 5/18/2007) leave a 1/16" blunt edge. Do not sharpen back side ofblade. When replacing blades, do not substitute anybolt for the special Nylok blade bolt. The Nylock bolt isself-locking, meeting the non-loosening requirementsfor this application. NOTICE ■ On mowers...
Page 10 - 0 A s s e m b l y; ASSEMBLY
1 0 A s s e m b l y 29936 (Rev. 5/18/2007) ASSEMBLY Center Shield To allow more lift on tractors with minimum groundclearance, such as Fords, IH LoBoy, Kubotas, Satohs,etc., a center belt shield is not offered. Refer topage 24. If the box of parts has a center belt shield, boltcenter belt shield bra...
Page 11 - A s s e m b l y 11
A s s e m b l y 11 29936 (Rev. 5/18/2007) and idler bracket. Install 5/8 x 2-1/2 carriage boltthrough slot and idler, and secure with 5/8" nut and lockwasher. Install a 5/8 x 3" bolt through second idler. Put these 5/8" flat washers over bolt, and install assembly to rightside of rear ve...
Page 12 - 2 A s s e m b l y
1 2 A s s e m b l y 29936 (Rev. 5/18/2007) Bring the belt back across the center sheave in thecenter groove over to the right outside sheave. Figure 7. Then thread it back across the front of the centersheave in the top groove. Figure 8. Proper Twist: The belt then follows with a 3/4 twistback under...
Page 13 - A ss e mb l y 1 3
A ss e mb l y 1 3 29936 (Rev. 5/18/2007) Figure 9. L59-AC/C & L306-AC/C Mounting Frame Assembly Photo
Page 14 - 4 A s s e m b l y
1 4 A s s e m b l y 29936 (Rev. 5/18/2007) Figure 10. L59-AC/C & L306-AC/C Mounting Frame Assembly Photo
Page 15 - A ss e mb l y 1 5
A ss e mb l y 1 5 29936 (Rev. 5/18/2007) Figure 11. L59-AC/B&C & L306-AC/B&C Hydraulic Lift Assembly Photo
Page 16 - 6 A s s e m b l y
1 6 A s s e m b l y 29936 (Rev. 5/18/2007) Figure 12. L59-AC/B&C & L306-AC/B&C Manual Lift Assembly Photo
Page 17 - A ss e mb l y 1 7; NOTES
Page 18 - 8 P a r ts
1 8 P a r ts 29936 (Rev. 5/18/2007) L59-AC/B & C & L306-AC/B & C Mounting Frame
Page 19 - P a r ts 1 9
P a r ts 1 9 29936 (Rev. 5/18/2007) L59-AC/B & C & L306-AC/B & C Mounting Frame REF PART QTY DESCRIPTION 1 3652 1 V-belt, special W188 (for L59) -or- 1 10859 1 V-belt, special W205 (for L306) 2 4336 2 V-idler sheave with bearing 3 4335 2 V-idler sheave less bearing 4 6095 2 Bearing 5 745...
Page 20 - 0 P a r ts
2 0 P a r ts 29936 (Rev. 5/18/2007) Spindles and Blades REF PART QTY DESCRIPTION 1 3761 1 Spindle assembly (for left hand rota-tion) 2 5089 2 Seal 3 4114 1 Sleeve 4 4115 1 Sel-lock pin 5 4107 2 Bearing cone 6 4117 1 Housing with cups 7 4106 2 Bearing cup 8 1972 1 Grease fitting 9 28897 1 Spindle sha...
Page 21 - P a r ts 2 1; Special Notes
P a r ts 2 1 29936 (Rev. 5/18/2007) Lift Chain Hook-Up Table Special Notes (Refer to numbers in parentheses in above table) 1. Hook one 13-link chain between holes “C” & “D”. 2. Fasten one 10-link and one 7-link chain together. 3. Hook lower end of spring in crotch chain. 4. Hook spring into cha...
Page 22 - 2 P a r ts
2 2 P a r ts 29936 (Rev. 5/18/2007) Manual Height Adjustment
Page 23 - P a r ts 2 3
P a r ts 2 3 29936 (Rev. 5/18/2007) Manual Height Adjustment REF PART QTY DESCRIPTION 1 ----- - Chain (see chart for chain used on your mounting) 2 4155 2-3 1/4 Cold shut repair link 3 10693 1 Manual height adjustment lever assembly 4 484 1-2 5/8 x 1 x 7/16 HT Sleeve 5 10706 1 3-3/8 Long compression...
Page 24 - 4 P a r ts
2 4 P a r ts 29936 (Rev. 5/18/2007) 59, L59, & L306 Mower Frame Assembly
Page 25 - P a r ts 2 5
P a r ts 2 5 29936 (Rev. 5/18/2007) 59, L59, & L306 Mower Frame Assembly REF Model Red & Yellow Mowers Model L59 White Mowers L306 Mowers 1976 & Later L306 Mowers Prior to 1976 QTY DESCRIPTION 1 9700 9701 9702 9702 1 Frame only 2 25513 25511 24189 13426 1 Left side shield 3 25512 25510 2...
Page 26 - 6 P a r ts
2 6 P a r ts 29936 (Rev. 5/18/2007) 59 & L306 Leaf Mulcher Operation: To do a satisfactory job of leafmulching, the mower should be adjusted soblades are about 1-1/2" above ground and the back of themower slightly lower than the front. Themower should be run at full rpm with tractorin first ...
Page 27 - P a r ts 2 7
P a r ts 2 7 29936 (Rev. 5/18/2007) 59 Casters REF PART QTY DESCRIPTION 1 29750 1 59 & L59 Right and left caster bundle 2 12243 1 Caster yoke (includes bolt, nut & 2 sleeves) 3 29746 a 1 Right caster arm asy, 13-5/32" long -or- 3 6761 a 1 Right caster arm, 16-5/32" long 4 29747 a 1 L...
Page 28 - 8 P a r ts
2 8 P a r ts 29936 (Rev. 5/18/2007) L306 Casters REF PART QTY DESCRIPTION A 24095 - L306 Caster assembly bundle 1 13400 1 Caster assembly 2 15638 1 10" Caster wheel with sleeve 3 23857 1 Caster wheel yoke assembly 4 13435 1 Caster arm assembly 5 13444 1 Left caster adjustment bracket 6 13444 1 R...
Page 29 - A p p e n d i x 2 9; BOLT TORQUE CHART
A p p e n d i x 2 9 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...
Page 30 - 0 A p p e n d i x; BOLT SIZE CHART
3 0 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............
Page 31 - WARRANTY
F-3079 (Rev. 6/1/2007) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Information ...
