Page 2 - ii; I n t r o d u c t i o n; DANGER
ii I n t r o d u c t i o n Gen’l (Rev. 5/23/2005) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual...
Page 3 - TABLE OF CONTENTS; WARNING
I n t r o d u c t i o n 1 MAN0116 (Rev. 4/15/2004) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSIDE FRONT COVER GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY RULES . . . . . . . . . . . . . . . . ...
Page 4 - S a f e t y; TRAINING; SAFETY RULES
2 S a f e t y Mow’n Machine Vacuum (10/8/2004) TRAINING Safety instructions are important! Read all a t ta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To locat...
Page 5 - TRANSPORTATION
S a f e t y 3 Mow’n Machine Vacuum (10/8/2004) Look down and to the rear and make sure area is clear before operating in reverse. Do not operate or transport on steep slopes. Do not stop, start, or change directions sud- denly on slopes. Use extreme care and reduce ground speed on slopes and...
Page 6 - SAFETY & INSTRUCTIONAL DECALS; Replace Immediately If Damaged!; SHIELD MISSING; Use a clean, damp cloth to clean safety decals.
4 S a f e t y MAN0118 (Rev. 12/23/2004) SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! SHIELD MISSING DO NOT OPERATE -- PUT SHIELD ON DANGER 18869 4 - PN 18869 MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. 5...
Page 7 - ROTATING DRIVELINE; CONTACT CAN CAUSE DEATH; CAUTION; PINCH POINT; AVOID INJURY FROM
S a f e t y 5 MAN0118 (Rev. 12/23/2004) SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! DANGER ROTATING DRIVELINE CONTACT CAN CAUSE DEATH KEEP AWAY! DO NOT OPERATE WITHOUT - All driveline guards, tractor and equipment shields in pla...
Page 8 - O p e r a t i o n; OPERATION; FIXED ANGLE HEIGHT ADJUSTMENT
6 O p e r a t i o n MAN0118 (Rev. 12/23/2004) OPERATION Safety instructions are important! Read all a t ta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To locat...
Page 9 - UNEVEN TERRAIN; PRE-OPERATION CHECK LIST
O p e r a t i o n 7 MAN0118 (Rev. 12/23/2004) Operate tractor engine at half throttle when de-thatch-ing grass or sweeping dirt. When de-thatching grass, stop tractor, disengage PTO,turn off key and check for grass wrap around PTO shaftand universal shaft every 30 minutes of operation. Use the gauge...
Page 10 - S e r v i c e; SERVICE; LUBRICATION
8 S e r v i c e MAN0118 (Rev. 12/23/2004) SERVICE Always wear relatively tight and belted clothing t o a v o i d g e t t i n g c a u g h t i n m o v i n g pa r ts . We a rs tu rd y, rou gh - s ol e d wo rk s h o e s a n d p ro te c t i v eequipment for eyes, hair, hands, hearing, and head;and resp...
Page 11 - A s s e m b l y; ASSEMBLY; DEALER SET-UP INSTRUCTIONS
A s s e m b l y 9 MAN0118 (Rev. 12/23/2004) ASSEMBLY DEALER SET-UP INSTRUCTIONS Assembly of this sweeper is the responsibility of theWOODS dealer. It should be delivered to the ownercompletely assembled, lubricated, and adjusted fornormal cutting conditions. FIXED ANGLE MOUNT KIT INSTALLATION (Figur...
Page 12 - -WAY ANGLE MOUNT KIT
1 0 A s s e m b l y MAN0118 (Rev. 12/23/2004) Figure 3 . 2-Way Angle Sweeper Installation 2-WAY ANGLE MOUNT KIT (Figure 3) Attach upper actuator mount (9) to square upright maston Sweeper broom head using 1/2 x 3 bolt and 1/2locknut. Mark Sweeper input driveshaft at 8-1/4 inches from thecenter cross...
Page 13 - ATTACHING SWEEPER TO TRACTOR
A s s e m b l y 11 MAN0118 (Rev. 12/23/2004) ATTACHING SWEEPER TO TRACTOR (Figure 4) Replace existing step on 2-way angle mount of tractorwith shorter step supplied with sweeper. Remove cotterpin on end of step rod and slide out. Install shorter stepand replace rod and cotter pin. Keep existing step...
Page 15 - D e a l e r C h e c k L i s t; DEALER CHECK LISTS; PRE-DELIVERY CHECK LIST; DELIVERY CHECK LIST
D e a l e r C h e c k L i s t 1 3 MAN0118 (Rev. 12/23/2004) DEALER CHECK LISTS PRE-DELIVERY CHECK LIST (Dealer Responsibility) ___ Inspect the Mow'n Machine and attachments thoroughly after assembly to be certain it is set upproperly before delivering it to the customer. ___ The following check list...
Page 16 - P a r ts; -WAY ANGLE SWEEPER ASSEMBLY
1 4 P a r ts MAN0118 (Rev. 12/1/2006) 2-WAY ANGLE SWEEPER ASSEMBLY 63 61 62 14 60 58 57 56 55 9 47 54 53 52 51 6 50 59 15 42 35 34 33 32 15 20 9 16 17 18 10 30 8 10 13 11 8 1 4 9 5 4 17 18 21 8 9 7 3 2 8 12 13 23 22 24 45 37 36 37 38 38 38 39 44 43 40 41 41 3 46 48 48 25 28 32 32 31 30 29 27 26 CD46...
Page 18 - FIXED ANGLE SWEEPER MOUNT KIT ASSEMBLY
1 6 P a r ts MAN0118 (Rev. 12/1/2006) FIXED ANGLE SWEEPER MOUNT KIT ASSEMBLY SEE SWEEPSTER ® MANUAL FOR SWEEPSTER ® PARTS. 41 -- DECAL SET TRIM INPUT SHAFT 6--1/2 17 16 31 20 32 33 34 35 39 38 37 36 30 40 19 18 15 14 13 8 10 11 10 7 6 5 4 3 2 1 CD4649A REF PART QTY DESCRIPTION - 73959 - Fixed angle ...
Page 19 - -WAY ANGLE SWEEPER WIRE DIAGRAM
P a r ts 1 7 MAN0118 (Rev. 12/1/2006) 2-WAY ANGLE SWEEPER WIRE DIAGRAM (+) (--) 2 2 3 4 A CD4661-- var K C A L B GREEN RED GREEN PURPLE PURPLE GREEN WHITE BLACK WHITE BLACK 2 WAY FEMALE CONNECTORTO ACTUATOR MOTOR 15 AMP FUSE 5 WAY FEMALECONNECTOR TORELAY. MOUNT RELAY TO SEATHINGE CENTER MOUNTING BOL...
Page 20 - A p p e n d i x; BOLT TORQUE CHART
1 8 A p p e n d i x Bolt Torque & Size Charts (Rev. 8/14/2002) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual p...
Page 21 - BOLT SIZE CHART; SAE Bolt Thread Sizes; ABBREVIATIONS
A p p e n d i x 1 9 Bolt Torque & Size Charts (Rev. 8/14/2002) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. 5/16 3/8 1/2 5/8 3/4 7/8 SAE Bolt Thread Sizes MM 25 50 75 100 125 150 175 IN 1 2 3 4 5 6 7 Metric Bolt Thre...
Page 22 - LIMITED WARRANTY; Zero-Turn Mower and; Utility Vehicle Replacement Parts)
F-8495 MM & Boundary Repair Parts (Rev. 2/15/2006) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com LIMITED WARRANTY (Mow’n Machine TM Zero-Turn Mower and Woods Boundary TM Utility Vehicle Replac...
Page 23 - Zero-Turn Mowers and Woods Boundary
F-8045 MM & Boundary (Rev. 7/14/2006) LIMITED WARRANTY (Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Information Below and Save For Future Reference . Date Purchased: __________________________ From (Dealer): _____________________________________ Model N...
