Winegard RS-1500 - Manual

Winegard RS-1500 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – CONNECTING COAX CABLE TO THE ANTENNA; Push the cable up until the end of the connector is; to the right; until the connector is; INSTALLING ANTENNA ON MOUNT; FIGURE 3; Antenna; FIGURE 1; ATTACHING MOUNT TO ROOF; Run cable supplied down through mount; TV
Page 3 – CONNECTING POWER SUPPLY; Select location for power supply. Run two coax cables; FIGURE 6; CHECKING OPERATION OF POWER SUPPLY; This unit is equipped with a polyswitch; FIGURE 7; FIGURE 8; IMPORTANT
Page 4 – WHAT TO DO WHEN YOUR RV/TV ANTENNA IS NOT WORKING PROPERLY; TO TEST SYSTEM; downlead supplies +12 VDC to preamp in antenna.

Loading the manual

MODEL RS-1500

OMNIDIRECTIONAL TV/FM ANTENNA

PARTS LIST

WARNING!

To prevent FIRE or SHOCK HAZARD, avoid exposure of power
supply to moisture.

NOTE:

Please read all instructions

before

beginning installation!

#1. ANTENNA

#3. CABLE TOOL
NOT INCLUDED WITH
RV MANUFACTURER
INSTALLED UNITS.

#6. CARRIAGE
BOLT

#5. HEX FLANGE NUTS

#2. COAX CABLE

TOOLS NEEDED

#2 Phillips screwdriver

7/16” wrench

Medium slot screwdriver

Cable tool

Wire stripper

1. (1) Antenna

2. (1) 15' RG-6 Low Loss Coax Cable

3. (1) Cable Tool

4. (1) Power Supply RV-7542

5. (4) 1/4-20 Hex Flange Nuts

6. (4) 1/4-20 Carriage Bolts

7. (2) Insulated Quick-Disconnect
Terminals

8. Mount

9. (4) Lag Screws 1/4” x 1-1/4”

10. (4) Washers 1/4”

11. (1) Roof Gasket

12. (1) Cable Gasket Plug

13. (1) Antenna Gasket

#4. POWER SUPPLY
AND SCREWS

#13. ANTENNA
GASKET

#10. WASHERS

#9. LAG SCREWS

#8. MOUNT

#11. ROOF GASKET

#12. CABLE
GASKET PLUG

#7. INSULATED QUICK
DISCONNECT TERMINALS

Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 319/754-0600 Fax 754-0787 • www.winegard.com

CABLE PROVIDED
BY INSTALLER FOR RV
MANUFACTURER
INSTALLED UNITS.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - CONNECTING COAX CABLE TO THE ANTENNA; Push the cable up until the end of the connector is; to the right; until the connector is; INSTALLING ANTENNA ON MOUNT; FIGURE 3; Antenna; FIGURE 1; ATTACHING MOUNT TO ROOF; Run cable supplied down through mount; TV

CONNECTING COAX CABLE TO THE ANTENNA 1.Slide small antenna gasket (previously removed fromthe middle of the large mount gasket) onto coax.2.Slide coax cable (with connector installed) into cabletool through the slot in the side of the tool, hex end up,Figure 2. 3. Push the cable up until the end of ...

Page 3 - CONNECTING POWER SUPPLY; Select location for power supply. Run two coax cables; FIGURE 6; CHECKING OPERATION OF POWER SUPPLY; This unit is equipped with a polyswitch; FIGURE 7; FIGURE 8; IMPORTANT

3 CONNECTING POWER SUPPLY 1. Select location for power supply. Run two coax cables (three if Set 2 jack is going to be used) (RG-59 type)between locations and install connectors on each end. Mark cables so "cable input", "TV output" "Set 2"may be identified. Antenna downlead ...

Page 4 - WHAT TO DO WHEN YOUR RV/TV ANTENNA IS NOT WORKING PROPERLY; TO TEST SYSTEM; downlead supplies +12 VDC to preamp in antenna.

Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 319/754-0600 Fax 754-0787 • www.winegard.com Printed in U.S.A. © 2002,2005 Winegard Company 2451233 Rev5 10/10 WHAT TO DO WHEN YOUR RV/TV ANTENNA IS NOT WORKING PROPERLY TO TEST SYSTEM HOW YOUR SYSTEM WORKS WARNING DO NOT install coupl...