Windsor SP13 Manual - Free PDF Download

Page 2 - MACHINE DATA LOG/OVERVIEW; YOUR DEALER; MODEL

For the name and address of your dealer contact: Windsor Industries __________________________________________________________________________________________________ _______________________________________________________________________________________________ _____________________________________...

Page 3 - TABLE OF CONTENTS; HOW TO USE THIS MANUAL; Handle Installation; GROUP PARTS LIST; Handle Group

TABLE OF CONTENTS Machine Data Log/Overview. .........................2 Table of Contents ...........................................3 HOW TO USE THIS MANUAL How to use this Manual..................................4 SAFETY Important Safety Instructions .........................1-1 Hazard Intensity L...

Page 5 - IMPORTANT SAFETY INSTRUCTIONS; When using an electrical appliance, basic precaution; READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.; SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. ! WARNING: To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to r...

Page 6 - HAZARD INTENSITY LEVEL; WARNING; WARNING; WARNING; CAUTION; CAUTION

HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the follow...

Page 7 - GROUNDING INSTRUCTIONS:; GROUNDING INSTRUCTIONS

THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause se...

Page 8 - TECHNICAL SPECIFICATIONS; ITEM

TECHNICAL SPECIFICATIONS ITEM DIMENSION/CAPACITY Construction Heavy-duty die cast aluminum deck with heavy-duty rubber bumper, tubular steel adjustable handle with die cast aluminum handle housing Motor SP13, SP15, SP17, SP20 1.0 hp SP17X, SP20X, SPDS20 1.5 hp Brush/Pad speed SP13, SP15, SP17, SP20,...

Page 9 - HANDLE INSTALLATION

HANDLE INSTALLATION STORM POLISHER 980100 03/08/03 2-2 The machine is shipped with handle unassembled. Follow these steps for installation: 1. Remove handle and deck assembly from carton. 2. Attach handle assembly to base using hardware kit (47331) (attached to handle in a plastic bag) items 1, 2, a...

Page 10 - OPERATION; CONTROLS

OPERATION STORM POLISHER 980100 03/08/03 2-3 CONTROLS 1. Safety Lock – Prevents unintended operation of the machine. 2. Switch Levers – Turns machine on/off. 3. Adjustment Handle – Allows the handle to be adjusted to a comfortable operating position. The handle adjust bar (14344) for the polishersar...

Page 11 - DAILY MAINTENANCE; PAD DRIVER INSTALLATION

OPERATION ! CAUTION For indoor use only. To prevent possible damage to the floor when using the brush option, use water or other approved cleaning solution while operating. When using the pad option, always keep the machine moving when in contact with the floor. ! WARNING High starting torque. Hold ...

Page 12 - MAINTENANCE; SCRUB BRUSHES; FINISHED FLOORS; SERVICE SCHEDULE; UNCOATED FLOORS

MAINTENANCE SCRUB BRUSHES NOTE: All original equipment brushes are equipped with “Perform Alert � ”. This feature will tell the operator when it is time to replace the scrub brushes. “Perform Alert � ” brushes have pre trimmed bright yellow tufts to indicate the length of a worn out brush. When the...

Page 13 - TROUBLESHOOTING

TROUBLESHOOTING PROBLEM CAUSE SOLUTION Machine will not run Circuit breaker tripped in building. Check and reset. Power switch failure. Test switch for continuity and replace if necessary. Tripped circuit breaker. Reset. Faulty power cord. Replace. Replace. CAUTION: To reduce the risk of electrical ...

Page 14 - BRUSH/PAD DRIVER GROUP

BRUSH/PAD DRIVER GROUP 1A 1B 1D 1C 3 3 2A-W STORM POLISHER 980100 04/24/06 3-1

Page 16 - FRAME GROUP

FRAME GROUP STORM POLISHER 980100 03/08/03 3-3 14 15 16 21 17D 17B17C 17A MOTOR ASMSEE PG 3-5 18C18D 18A18B 19 20 12 13 11 8 10 4 6 5 7 3 22 23 2 1 8 9

Page 18 - MOTOR GROUP

MOTOR GROUP STORM POLISHER 980100 03/08/03 3-5 SP13, SP15, SP17, SP20 9 3 11 2 4 SP17X, SP20X 7 SPDS20 12 11 8 10 12 11 1 4 1 5 12 6

Page 20 - HANDLE GROUP

HANDLE GROUP STORM POLISHER 980100 03/09/05 3-7 1 11 2 0 12 2 5 14 13 6 17 1 8 3 7 1 9 9 15 8 4 10 21 22 1 6 9

Page 22 - WIRING GROUP

WIRING GROUP STORM POLISHER 980100 11/15/03 3-9 8 4 6 2 11 6 11 3 1 10 9 7 5 12 PRIOR TO SN *

Page 24 - DESCRIPTION

WIRING DIAGRAM / SPARE PARTS SUGGESTED SPARE PARTS PART NO. DESCRIPTION SERIAL NO. FROM NOTES: 87202 WASHER, BEARING (HANDLE ADJ) 73990 SPRING, EXT .5 OD X 3.5L 73993 SPRING, COMP .48 OD X .91 L 72123 SWITCH. 25A SPST 125-250V SNAP 14344 BAR, HANDLE ADJ 66334 PIN, PIVOT, HANDLE ADJ 67430 ROD, HANDLE...