White Rodgers 3098-156 - Manual
White Rodgers 3098-156 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – F or less). The low ambient slightly increases; SPECIFICATIONS; SPDT; Sensing Bulb Type: Universal Replacement; Thermocouple “slip-in”; Terminal Designations:; INSTALLATION; Turn off gas and power until replacement is complete.; CAUTION; Internal Schematic
- Page 3 – INSTRUCTIONS D’INSTALLATION; DESCRIPTION; PRÉCAUTIONS; ATTENTION; AVERTISSEMENT
- Page 4 – Désignation des bornes :
Printed in U.S.A.
PART NO. 37-3600C
Replaces 37-3600B
9711
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE
PERSONAL INJURY AND/OR PROPERTY DAMAGE.
DESCRIPTION
Operator: Save these instructions for future use!
INSTALLATION INSTRUCTIONS
3098 MERCURY
FLAME SENSOR
3098-134 & 3098-156
Standard Replacement
Mercury Flame Sensor
The 3098-134 and 3098-156 Mercury Flame sensors are
designed as universal replacements for types currently
used on cycling pilot ignition systems. They will replace
sensors used in “thermocouple” type (slip-in) pilot burners.
The bulbs on both flame sensors have additional grooves
to accept retaining clips (C-rings) allowing them to replace
most existing sensors.
The 3098 Flame Sensors are SPDT (single-pole double-
throw) devices, with switchcases designed to plug into
cycling pilot gas valves. These flame sensors should not
be used in appliances other than those listed in the cross
reference.
PRECAUTIONS
If in doubt about whether your wiring is millivolt, line, or low
voltage, have it inspected by a qualified heating and air
conditioning contractor or licensed electrician.
Do not exceed the specification ratings.
All wiring must conform to local and national electrical
codes and ordinances.
This control is a precision instrument, and should be
handled carefully. Rough handling or distorting compo-
nents could cause the control to malfunction.
Do not use on circuits exceeding specified volt-
age. Higher voltage will damage control and could
cause shock or fire hazard.
To prevent electrical shock and/or equipment
damage, disconnect electric power to system at
main fuse or circuit breaker box until installation
is complete.
Shut off main gas to heating system until installa-
tion is complete.
Label all wires prior to disconnection when ser-
vicing controls. Wiring errors can cause improper
and dangerous operation.
Following installation or replacement, follow ap-
pliance manufacturer's recommended installa-
tion and/or service instructions to insure proper
operation.
WARNING
!
CAUTION
!
WHITE-RODGERS
ATTENTION!
This product contains mercury. There will not be any exposure to mercury under normal conditions of use. This product may
replace a unit which contains mercury. Do not open mercury cells. If a cell becomes damaged, do not touch any spilled
mercury. Wearing nonabsorbent gloves, take up the spilled mercury with sand or other absorbent material and place into a
container which can be sealed. If a cell becomes damaged, the unit should be discarded. Mercury must not be discarded in
household trash. When this unit or the unit it is replacing is to be discarded, place in a suitable container and return to us.
WHITE-RODGERS DIVISION
EMERSON ELECTRIC CO.
9797 REAVIS RD., ST. LOUIS, MO. 63123-5398
(314) 577-1300,
FAX (314) 577-1517
9999 HWY. 48, MARKHAM, ONT. L3P 3J3
(905) 475-4653,
FAX (905) 475-4625
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Type 3098-134 is equipped with a “high-mass” element,and is used in applications where a medium sensorresponse time (typically 45 to 60 seconds) is desired. Type 3098-156 contains a “low-mass” element, and isused in applications where a short response time (usuallybetween 30 to 45 seconds) is requ...
3098-134 & 3098-156 Détecteurs de flamme au mercure standard de rechange INSTRUCTIONS D’INSTALLATION WHITE-RODGERS R PIÈCE N o 37-3600C Remplace 37-3600B 9711 WHITE-RODGERS DIVISIONEMERSON ELECTRIC CO.9797 REAVIS RD., ST. LOUIS, MO. 63123(314) 577-1300, Télécopieur (314) 577-1517 9999 HWY. 48, M...
2 INSTALLATION 1. Couper le gaz et l’électricité jusqu’à ce que l’installation soitterminée. 2. Retirer le détecteur de flamme défectueux du brûleur de laveilleuse et le débrancher du robinet à gaz. 3. Aligner le bout du détecteur de flamme défectueux sur lebout du détecteur de rechange. Ne pas déro...
