Whirlpool WFG320M0BS0 - Installation Manual

Whirlpool WFG320M0BS0

A user manual for gas ranges outlines essential setup, maintenance, and operation procedures to ensure safe and efficient performance. The document covers critical installation checks–such as verifying fuel line compatibility, tightening connections, and confirming ignition functionality–to prevent hazards like explosions. It also details general care tasks, including cleaning surface burners, replacing grates, and troubleshooting the control panel (e.g., LCC/Lock Control system). Safety warnings emphasize proper assembly and burner testing, while diagrams illustrate key components and operational steps. Customer service contact information for support is included in some sections.

1

2

3

4

Table of Contents:

Page 1 – Gas Range Installation Checklist and Safety Setup
Page 2 – Burner Maintenance and LCC System Operation Guide
Page 3 – Gas Stove Installation Verification and Safety Warnings
Page 4 – LCC System Controls and Burner Maintenance

Loading the manual

INSTALLATION CHECKLIST FOR GAS RANGES

1. Determine if a fuel conversion is needed

Your range will require a fuel conversion if you intend to connect to

propane.

NOTE:

Propane conversions must be completed by a qualified service

technician (see the gas conversion section in the installation instructions

that came with your range).

2. Verify properly tightened fuel connections.

Example of how to make a gas connection.

IMPORTANT:

All connections must be wrench-tightened. Do not make

connections to the gas regulator too tight. Making the connections too

tight may crack the regulator and cause a gas leak. Do not allow the

regulator to turn when tightening fittings.

3. Verify the gas regulator is “ON”

1. Locate gas pressure regulator in the back of the range.

Gas pressure regulator location. Rear view of range.

Figure D: Gas pressure regulator location. Rear view of range.

IMPORTANT:

Do not remove the gas pressure regulator.

2. Check that the gas pressure regulator shutoff valve is in the“ON”

position.

Gas regulator lever position “A. ON” and “B. OFF”

IM

PORTANT:

The factory default setting is the “ON” position. If the

range does not work, verify that the valve is in the “ON” position.

4. Verify surface burner function

Surface gas burner assembly

To ignite burner:

1. Push in and turn knob counter-clockwise to LITE. All surface burners

will click. Only the burner with the control knob turned to LITE will

produce a flame.

2. Turn knob to anywhere between High and Low. The clicking will stop.

To ignite burner

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make

sure gas pressure does not exceed 14" (36 cm) water

column.
Examples of a qualified person include:
licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.
Failure to do so can result in death, explosion, or fire.

A. Pressure regulator

connection fitting

B. Use Pipe-Joint compound.

C. Adapter

D. Flexible connector

E. Adapter

F. Use pipe-joint compound.

G. Manual shutoff valve

H. 1/2" (1.3 cm) or 3/4"

(1.9 cm) gas pipe

A. Burner cap

B. Alignment pins

C. lgniter

E. Burner base

F. Gas tube opening

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand: Whirlpool
Model: WFG320M0BS0
Document type: Installation Manual
Language(s): English, French
Pages: 4
File size: 1.3 MB
Format: PDF

Other Manuals for Whirlpool WFG320M0BS0

User Manual

Summary

Page 1 - Gas Range Installation Checklist and Safety Setup

Checklist for gas range installation covering fuel conversion needs, regulator verification, connection tightening, burner function checks, explosion hazards, and assembly diagrams.

Page 2 - Burner Maintenance and LCC System Operation Guide

Instructions for cleaning surface burners and nozzles, replacing grates, operating the LCC system, aligning burner caps, control panel diagrams, and basic oven operation steps.

Page 3 - Gas Stove Installation Verification and Safety Warnings

Key installation checks including gas line compatibility, pressure verification, connection tightening, ensuring the gas valve is in the ON position, testing ignition function, and component assembly safety warnings.

Ask a question