Whirlpool WED5605MC - Manual
Whirlpool WED5605MC Dryer – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Troubleshooting
- Page 3 – Portes rondes avec câblage électrique :; Outils nécessaires; AVERTISSEMENT; Déconnecter le câblage de la porte
- Page 5 – Dépannage
- Page 6 – Puertas redondas con cableado eléctrico:; Herramientas necesarias; ADVERTENCIA; Desconecte el cableado de la puerta
- Page 8 – Vuelva a conectar el cableado (puertas con; Solución de problemas
1
DDRRYYEERR DDO
OO
ORR RREEVVEERRSSAALL IINNSSTTRRUUCCTTIIO
ONNSS
Round Doors with Electrical Wiring:
Tools Needed
Minimum 8" (203 mm) long TORX
®
, T20
®
, and T25
®
star drivers
#2 Phillips screwdriver
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
1. Disconnect wiring from door
Using a Phillips screwdriver, remove middle screw in hinge.
Disconnect wiring. Tuck wiring into opening.
2. Remove door from dryer
IMPORTANT:
If the protective film has not yet been removed from
the dryer, peel the film from the dryer door before proceeding.
Using a T25
®
screwdriver, remove the four screws securing the
door hinge to the dryer and lift the door up and out to remove. Place
the door on a soft towel or other non-scratch surface.
3. Move the door strike
Using a T25
®
screwdriver, remove the two screws securing the
door strike to the door frame of the dryer. Rotate the strike 180°
and attach to the opposite side of dryer door frame with the two
screws removed earlier, as shown.
4. Remove inner door from outer door
Position the door with the inside of the door facing up. Using a
Phillips screwdriver, remove the 10 screws securing the inner door
to the outer door.
5. Remove hinge
Remove cover plate to reveal hinge assembly. Then, using a T20
®
screwdriver, remove the six screws holding the hinge assembly in
place.
6. Remove latch
Flip and rotate the inner door 180° so that the thin section is at the
top and the thick section is at the bottom. Using a T25
®
screwdriver, remove the four screws securing the latch plate in
place.
TORX, T20 and T25 are trademarks of Acument Intellectual Property, LLC.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Whirlpool WED5605MC
Summary
2 7. Reinstall latch on opposite side Using a T25 ® screwdriver, reinstall the latch plate on the opposite side from which it was removed with the four screws removedearlier. 8. Reinstall hinge assembly on opposite side Flip over the inner door to the left. Using a T20 ® screwdriver, reinstall the h...
3 IINNSSTTRRUUCCTTIIO ONNSS PPO OUURR IINNVVEERRSSIIO ONN DDEE PPO ORRTTEE DDEE SSÉÉCCHHEEUUSSEE Portes rondes avec câblage électrique : Outils nécessaires Tournevis mm) long TORX ® , T20 ® et Tournevis Phillips n° 2 T25 ® † de 8" (203 mm) min. de long Tournevis cruciforme no 2 AVERTISSEMENT Ris...
5 14. Rebrancher le câblage (portes avec câblage électrique) Brancher le câblage. À l’aide d’un tournevis cruciforme, fixer l’ensemble de rotation à la charnière en utilisant la vis enlevée précédemment. Dépannage Voir le manuel d’utilisation ou consulter notre site Web et la Foire aux questions pou...
