Whirlpool W10526974A - Manual

Page 2 - Gas leaks cannot always be detected by smell.

2 WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. – WHAT TO DO IF YOU SMELL GAS: ...

Page 3 - INSTALLATION REQUIREMENTS; Tools and Parts; Tools needed; Location Requirements; WARNING

3 INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed Parts supplied Check that all parts are included. ■ Anti-tip bracket must be securely mounted to floor or w...

Page 4 - Mobile Home - Additional Installation Requirements; Mobile home installations require:; Product Dimensions; Range must be level after installation. Follow the; Cabinet Dimensions; If installing a range hood or microwave hood

4 Mobile Home - Additional Installation Requirements The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is n...

Page 5 - Type of Gas

5 Electrical Requirements IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.This range is equipped with an electronic ignition syst...

Page 6 - Gas Supply Line; Pipe-joint compounds that resist the action of LP gas; Flexible metal appliance connector:; Gas Pressure Regulator

6 Gas Supply Line ■ Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be ½" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials u...

Page 7 - INSTALLATION INSTRUCTIONS; Unpack Range; Remove shipping materials, tape and film from range.; On Ranges Equipped with a Storage Drawer:; Install Anti-Tip Bracket; from centerline as shown.; Excessive Weight Hazard; Tip Over Hazard

7 INSTALLATION INSTRUCTIONS Unpack Range 1. Remove shipping materials, tape and film from range. 2. Remove oven racks and parts package from inside oven. 3. Do not remove the shipping base at this time. 4. On Ranges Equipped with a Storage Drawer: Remove the storage drawer. See the “Storage Drawer” ...

Page 8 - Make Gas Connection; Typical rigid pipe connection; Explosion Hazard

8 Floor Mounting Wall Mounting 5. Using the Phillips screwdriver, mount anti-tip bracket to the wall or floor with the two #12 x 1 ⁵⁄₈ " screws provided. 6. Move range close enough to opening to allow for final gas and electrical connections. Remove shipping base, cardboard or hardboard from und...

Page 9 - Complete Connection; Verify Anti-Tip Bracket Is Installed and; On Ranges with a Storage Drawer:; Electrical Shock Hazard

9 3. Use a ¹⁵⁄₁₆ " combination wrench and channel lock pliers to attach the flexible connector to the adapters. Check that connector is not kinked. Complete Connection 1. Check that the gas pressure regulator shutoff valve is in the “on” position. 2. Open the manual shutoff valve in the gas supp...

Page 10 - Level Range; For Ranges with AquaLiftTM Technology or Steam Clean:; Electronic Ignition System; Initial lighting and gas flame adjustments; To adjust standard burner:

10 IMPORTANT: If there is a snapping or popping sound when lifting the range, the range may not be fully engaged in the bracket. Check to see if there are obstructions keeping the range from sliding to the wall or keeping the range foot from sliding into the bracket. Verify that the bracket is held ...

Page 11 - If the “low” flame needs to be adjusted:; Check Operation of Oven Bake Burner; Remove flame spreader:; Adjust Oven Bake Burner Flame (if needed)

11 If the “low” flame needs to be adjusted: 1. Light 1 burner and turn to lowest setting. 2. Remove the control knob.Hold the knob stem with a pair of pliers. Use a small flat-blade screwdriver to turn the screw located in the center of the control knob stem until the flame is the proper size. 3. Re...

Page 12 - If flame needs to be adjusted:; Adjust the air shutter as needed.; Warming Drawer or Premium Storage; Pull the storage drawer straight back to the drawer stop.

12 If flame needs to be adjusted: 1. Loosen the lock screw on the air shutter located at the rear of the broil burner. 2. Adjust the air shutter as needed. 3. Tighten lock screw. 4. Press CANCEL/OFF when finished. Warming Drawer or Premium Storage Drawer (on some models) Remove all items from inside...

Page 13 - If range does not operate, check the following:; If you need Assistance or Service:

13 To Replace: 1. Lift up the front of the drawer and place the rear of the drawer inside the range so that the drawer stop notch is behind the drawer glide. 2. Lower the drawer so that the edge of the slide rail drops into the slot in the drawer glide. 3. Slowly push the drawer into the range. NOTE...

Page 14 - GAS CONVERSIONS; LP Gas Conversion; Turn the manual shutoff valve to the closed position.; To Convert Gas Pressure Regulator (Natural Gas to LP Gas); On models with a warming drawer, an access cover

14 GAS CONVERSIONS Gas conversions from Natural gas to LP gas or from LP gas to Natural gas must be done by a qualified installer. LP Gas Conversion 1. Turn the manual shutoff valve to the closed position. 2. Unplug range or disconnect power. To Convert Gas Pressure Regulator (Natural Gas to LP Gas)...

Page 15 - To Convert Surface Burners (Natural Gas to LP Gas); LP Gas Orifice Spud Chart for Surface Burners; NG; Burner Rating

15 3. Remove plastic cover from gas pressure regulator cap. 4. Turn gas pressure regulator cap counterclockwise with a ⁵⁄₈ " combination wrench to remove. NOTE: Do not remove the spring beneath the cap. 5. Turn over the gas pressure regulator cap and reinstall on regulator so that the hollow end...

Page 17 - Complete Installation (Natural Gas to LP Gas); Natural Gas Conversion; To Convert Gas Pressure Regulator (LP Gas to Natural Gas)

17 4. Replace the “53” hood with a “090” hood. Install the LP gas broiler burner orifice hood, turning it clockwise until snug. IMPORTANT: Do not overtighten. 5. Place the broil burner on the broil burner orifice hood and insert the broil burner ceramic igniter in the hole in the rear of the oven. 6...

Page 18 - To Convert Surface Burners (LP Gas to Natural Gas); Natural Gas Orifice Spud Chart; To Convert Oven Bake Burner (LP Gas to Natural Gas); LP

18 4. Turn gas pressure regulator cap counterclockwise with a ⁵⁄₈ " combination wrench to remove. NOTE: Do not remove the spring beneath the cap. 5. Turn over the gas pressure regulator cap and reinstall on regulator so that the solid end faces out and the marking “  NG” is facing the direction...

Page 19 - To Convert Oven Broil Burner (LP Gas to Natural Gas)

19 4. Remove 2 screws from the front tabs of the flame spreader. Lift front of the flame spreader and pull forward to remove tabs from rear of oven and set it aside on a covered surface. 5. Remove 2 screws from the bake burner. 6. Slide the front of the bake burner to the side to remove tab from fro...

Page 20 - Complete Installation (LP Gas to Natural Gas); You may have to adjust the “LO” setting for each

5. Place the broil burner on the broil burner orifice hood and insert the broil burner ceramic igniter in the hole in the rear of the oven. 6. Position the broil burner against the top of the oven and attach it with 2 screws. 7. Replace storage drawer, warming drawer or premium storage drawer. See t...

Whirlpool W10526974A - Manual

Table of Contents:

Summary

Other Whirlpool Models