Whirlpool FFT M11 9X3BXY EE - Manual

You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:

• Visiting our website -

docs.whirlpool.eu

• Using QR Code

• Alternatively,

contact our After-sales Service

(See phone number in the warranty booklet). When

contacting our After-sales Service, please state the codes provided on your product’s identifi cation plate.

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance,

please register your product on

www.whirlpool.eu/register

EN

Quick guide

Before using the appliance read the Safety Instructions carefully.

xxxxxxxxxxxx

xxxx

OPENING OF THE DOOR DURING THE CYCLE

Laundry can be checked while the drying cycle runs and any

garments already dry can be removed, while drying continues for

the remaining items. After closing the door, press the "Start/Pause"

button to resume machine operation.

Keep the door closed until the cycle end to save time and energy.

DAILY USE

Doing this will keep your machine working at its BEST:

- remember to empty your water tank after each drying cycle.

- remember to clean your filters after each drying cycle.

Refer to the Care & Maintenance section.

1. Plug the dryer into the power supply socket.

2. Open the door and load garments; always refer to instructions on

clothing labels and the max loads indicated in the programme

section. Empty pockets. Make sure garments do not get caught

between the door and/or the door filter. Do not load items that

are dripping wet. Do not tumble dry large, very bulky items.

3. Close the door.

4. Press the "On/Off" button.

5. Select the most suitable programme for the type of fabric in that

load.

6. Select the options, if necessary.

7. Press the "Start/Pause" button to begin drying.

8. At the end of the drying cycle, a buzzer will beep. An indicator on

the control panel signals the end of the cycle. Pull the load out

immediately to prevent the formation of creases on laundry.

9. Turn the machine off by pressing the "On/Off" button, open the

door and pull the clothing out. If the machine is not switched off

manually, after about a quarter of an hour from the end of the

cycle , the appliance turns off automatically to save energy.

Note that some programme/option accords with "Crease Care"

system. This means that for some hours, after the end of the

drying cycle, the drum rotates at regular intervals to prevent the

formation of creases.

In case of power failure, it is necessary to press the "Start/Pause"

button to restart the cycle.

*MAX LOAD 9 Kg

(Dry load)

CARE LABEL

Always check the care labels, especially when placing garments in

the tumble dryer for the fi rst time. Below are the most commonly

used symbols:

May be tumble dried.

Do not tumble dry.

Tumble dry – high heat.

Tumble dry – low heat.

FIRST TIME USE

Make sure that the water tank is correctly inserted.

The dryer must be installed in a room with a temperature

ranging between 5°C and 35°C to ensure proper operation.

Before you use your dryer ensure that it has been in a upright

position for at least 6 hours.

CONTROL PANEL

1

On/Off button (hold for Reset)

2

Programme selection knob

3

Start/Pause button

Options buttons*

4

Dryness level

5

Start delay

6

Timed drying

7

Cycle end

8

Rapid

(hold for Key lock)

9

FreshCare+ (hold for Mute)

*Note: some models may have the wording in full instead of the icons.

INDICATORS

Dryness level:

Iron dry -

Hanger dry - Cupboard dry - Extra dry

Cycle phase:

Drying - Cool down - End of cycle.

Empty water tank

-

Clean secondary filter -

Clogged door filters -

Autoclean

Refer to Troubleshooting section:

Failure

call After-sales Service -

DEMO

Demo Mode

1

3

2

9

7

8

4

5

6

3’’

3’’

h

1

3

2

9

7

8

4

5

6

h

3’’

3’’