Whirlpool CSP2970HQ - Installation Manual

6 DIMENSIONS/CLEARANCES Dimension: Minimum Clearance: Front View Side View Back View ) PD Models (1950 mm 27" (686 mm) 5" (127 mm) 29" (737 mm) (267 mm) 10 1 / 2 " 76 3 / 4 " (1950 mm) 74 1 / 4 " (1886 mm) Non-Coin / Card-Ready Models Coin Models Coin Models Coin Models Non-C...

7 LOCATION REQUIREMENTS WARNING Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer.Do not install in a garage. Failure to do so can result in death, explosion, or fire. Your dryer can be installed in a basement, laundry room, or recessed area.This dryer is not in...

8 GAS DRYER ELECTRICAL REQUIREMENTS IMPORTANT: The dryer must be electrically grounded in accordance with local codes and ordinances or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, latest edition, or Canadian Electrical Code, CSA C22.1. If codes permit and a separ...

9 GAS REQUIREMENTS Gas Supply WARNING Explosion Hazard Use a new CSA International approved gas supply line.Install a shut-off valve.Securely tighten all gas connections.If connected to propane, have a qualified person make sure gas pressure does not exceed 13" (33 cm) water column. Examples of ...

12 DRYER VENTING REQUIREMENTS WARNING Fire Hazard Use a heavy metal vent.Do not use a plastic vent.Do not use a metal foil vent.Failure to follow these instructions can result in death or fire. WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governi...

13 DRYER VENTING REQUIREMENTS Vent Hoods 4" (102 mm) Diameter Exhaust Hoods Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exaust (such as flowers, rocks, bushes, or snow). Vent System Length Maximum Vent Length/Vent Connection Maximum...

14 DRYER VENTING REQUIREMENTS If an Exhaust Hood Cannot be Used The outside end of main vent should have a sweep elbow directed downward. If the main vent travels vertically through the roof, rather than through the wall, install a 180° sweep elbow on the end of the vent at least 2 ft. (610 mm) abov...

15 INSTALLING LEVELING LEGS 1. Prepare dryer for leveling legsNOTE: Slide dryer onto cardboard or hardboard before moving to avoid damaging floor covering. Using two or more people, move dryer to desired installation location. Take tape off front corners of dryer. Open dryer and remove the literatur...

16 LEVELING Leveling your dryer properly reduces excess noise and vibration. 1. Remove cardboard from beneath dryer. Place a level on top edges of dryer, checking each side and front. If not level, tip dryer and adjust feet up or down, repeating as necessary. 2. Grip dryer from top and rock back and...

17 GAS SUPPLY CONNECTION Type of Gas This dryer is equipped for use with natural gas. It is certified by UL for use with propane gas with appropriate conversion. No attempt shall be made to convert dryer from gas specified on serial/rating plate for use with a different gas without consulting the se...

18 ELECTRIC DRYER ELECTRICAL CONNECTIONS (FOR U.S.A. ONLY) Power Supply Cord Connection 4-wire receptacle (NEMA Type 14-30R) Go to “Connecting 4-Wire Connection: Power Supply Cord” section. WARNING Fire Hazard Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief. Disconnect po...

19 ELECTRIC DRYER ELECTRICAL CONNECTIONS Power Supply Cord Connection (cont.) 2. Insert power cord into strain relief. Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit wit...

20 ELECTRIC DRYER ELECTRICAL CONNECTIONS Connecting 3-Wire Connection: Power Supply Cord (cont.) 2. Connect white neutral wire (white or center) (D) to center terminal block. Tighten screw. 3. Connect remaining wires with outer terminal block screws (F). Tighten screws. Finally, re-install terminal ...

21 D D A A E B C B C E Remove Terminal Block Cover Before you start, disconnect power. Remove hold-down screw (D) and terminal block cover (A). A. Terminal block coverB. External ground conductor screwC. Center terminal block screwD. Hold-down screwE. Neutral ground wire Direct Wire Strain Relief1. ...

22 ELECTRIC DRYER ELECTRICAL CONNECTIONS Connecting 4-Wire Connection: Direct Wire IMPORTANT: A 4-wire connection is required where local codes do not permit the use of 3-wire connections. Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer can be moved if needed. Strip 5" (127 m...

23 ELECTRIC DRYER ELECTRICAL CONNECTIONS Connecting 3-Wire Connection: Direct Wire Use where local codes permit connecting cabinet-ground conductor to neutral wire. Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer can be moved if needed.Strip 31⁄2" (89 mm) of outer covering fr...

24 COMPLETE INSTALLATION 1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See “Electrical Requirements.” 2. Check that all parts are now installed. If there is an extra part, go back through the steps. 3. Check that you h...

25 REVERSING DRYER DOOR SWING (OPTIONAL) You can change your door swing from a right-side opening to left-side opening, if desired. Remove the Door Assembly 1. Place a towel or soft cloth on top of work space to avoid scratching of the surface. 2. Open dryer door. Remove button screws from cabinet s...

26 MAINTENANCE INSTRUCTIONS ■ Clean lint screen before and after each cycle. ■ Removing accumulated lint:From inside the dryer cabinet:Lint should be removed every two years or more often, depending on dryer usage. Cleaning should be done by a qualified person.From the exhaust vent:Lint should be re...

27 ELECTRONIC CONTROL SETUP INSTRUCTIONS IMPORTANT Electrostatic Discharge (ESD) Sensitive Electronics ESD problems are present everywhere. ESD may damage or weaken the electronic control assembly. The new control assembly may appear to work well after repair is finished, but failure may occur at a ...

28 ELECTRONIC CONTROL SETUP INSTRUCTIONS Control Setup Procedures IMPORTANT: Read all instructions before operating. The fabric setting buttons along with the digital display are used to set up the dryer controls. The display can contain four numbers and/or letters and a decimal point. These are use...

29 ELECTRONIC CONTROL SETUP INSTRUCTIONS Code Explanation 1. 00 MONEY COUNTER OPTION This option is either NOT SELECTED “OFF” or SELECTED “ON.” 1. 00 Not Selected “OFF.” 1. 0C Selected “ON.” ■ Press the DELICATES button three consecutive times to select “ON” and three consecutive times to remove (No...

31 ELECTRONIC CONTROL SETUP INSTRUCTIONS Code Explanation J. Cd PAYMENT MODE (COIN/DEBIT OPTION) J. Cd J. C_ J._d J. Ed Both coin and debit selected. Press the DELICATES button three consecutive times to change this selection. Coins selected, debit disabled. Press the DELICATES button three consecut...