Westinghouse WBB3700WF - User Manual

Page 2 - • Most of the packaging materials are recyclable.; CONTENTS

2 CONGRATULATIONS Congratulations and thank you for choosing our integration kit. Before you install the integration kit, we recommend that you read through the entire installation manual.To avoid the risks that are always present when you install an electrical appliance, it is important that the in...

Page 4 - mounting plate; REFRIGERATOR INTEGRATION KIT ITEMS

4 Item Quantity in kit Quantity required Description Two door model Single door model Top hinge bracket PNº 1433129 1 1 1 Slide-housing PNº 1445132 2 2 1 Slide-bar PNº 1421620 2 2 1 Location bracket front footing PNº 1444993 Note: this part is to be used on all models other than WTB2300, WTB2500, WT...

Page 5 - CUPBOARD DIMENSIONS; internal and measured in millimetres; internal and in millimetres

5 CUPBOARD DIMENSIONS IMPORTANT! Pages 5, 6, 7 and 8 should be given to the person responsible for cupboard design and construction. The cupboard dimensions required for each model are shown on page 6, 7 & 8. 1. All sizes are internal and measured in millimetres . 2. It is important to ensure th...

Page 6 - Panel A; Dim A; Panel B; Panel D

6 CUPBOARD DIMENSIONS NOTE: All sizes are internal and measured in millimetres . For ‘lettered’ dimensions refer to the table on page 5. Panel A (sides) Dim B 100mm Dim A Dim A + Skirting height Panel B (back) Dim A + Skirting height + boar d thickness Dim C + 2x Board thickness Dim B Dim C Dim E 80...

Page 7 - Clearances

7 CUPBOARD DIMENSIONS Clearances When installed the refrigerator needs to have adequate air ventilation. It is important to ensure there is good airflow from the front to underneath and up the rear to the top of the cabinet (see diagrams). Front airflow cut-out Dim E Front airflow cut-out 50mm NOTE:...

Page 8 - Cabinet construction; INSTALLATION OF 120 ̊ HINGE; Use 120o hinge to attach the cupboard door to the cabinet.

8 CUPBOARD DIMENSIONS When positioned in a corner the clearance of Dim G on the hinge side of the cabinet will allow the doors to be opened enough to enable the removal of the crisper bins. Dim C Dim G 120° NOTE: Use the 120° hinges supplied with the kit to attach the cupboard door to the cupboard.A...

Page 9 - PREPARATION; Figure 1; Figure 2; ATTACHING THE TOP HINGE BRACKET; Re-attach hinge and screws ensuring that refrigerator; Top hinge bracket fitted

9 PREPARATION 1. Unpack refrigerator, removing foam packing.2. Lay the refrigerator down on its back on a piece of soft packing material. Use caution and two people while laying the appliance down. 3. Remove top door stopper if fitted (Figure 1).4. Place adjustable rollers in the fully retracted pos...

Page 10 - ATTACHING SLIDE-HOUSING TO REFRIGERATOR DOORS; as shown in the diagrams.; single door

10 ATTACHING SLIDE-HOUSING TO REFRIGERATOR DOORS 1. Ensure slide-housing is positioned squarely as shown.2. Ensure that the slide-housing is positioned on the door as shown in the diagrams. Note: The slide-housing ‘protruding edge’ side must always be closest to the door handle side (diagram right)....

Page 11 - the maximum thread can be formed in the metal.; Figure 5

11 NOTE: For single door models, the door handle must be completely removed to provide clearance to the cupboard door and the resulting handle mounting holes hidden with a cover. Installer must use a tape or plastic cover that suits the installation appearance (not supplied). 3. While the slide-hous...

Page 12 - PLACING REFRIGERATOR IN CUPBOARD; two people if necessary.; Figure 7; REFRIGERATOR ALIGNMENT; Position bottom location bracket as shown (opposite; Figure 8; Figure 9a

12 PLACING REFRIGERATOR IN CUPBOARD 1. Ensure cupboard is level and square.2. Put refrigerator into cupboard. Use caution and two people if necessary. 3. Insert slide bars into slide-housings (Figure 7). NOTE: Ensure the refrigerator is level in the cupboard. Raise the front of the refrigerator by u...

Page 13 - Slowly close the cupboard door (pushing the; NOTE: When attaching; all screws; to cupboard, first drill

13 SECURING THE REFRIGERATOR IN THE CUPBOARD 4. Slowly close the cupboard door (pushing the refrigerator back) until it is slightly ajar, i.e. with a gap of about 4mm (Figure 11). You may have to reposition the refrigerator back or forward until the 4mm gap is obtained. Ensure that the refrigerator ...

Page 14 - ATTACHING SLIDE-BAR TO THE CUPBOARD DOOR

14 ATTACHING SLIDE-BAR TO THE CUPBOARD DOOR 1. Fully open cupboard door (120°).2. Open refrigerator door until it rests against the cupboard door. 3. Position slide-bar in slide-housing so that all three holes are visible when both doors are fully open (120°). This position is typically 125mm from t...

Westinghouse WBB3700WF - User Manual

Table of Contents:

Summary

Other Westinghouse Refrigerators Models