Weider Pro 2250 - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS

2 TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 4 - BEFORE YOU BEGIN

4 BEFORE YOU BEGIN Thank you for selecting the versatile WEIDER ® PRO 2250 weight system. The weight system offers animpressive array of weight stations designed to devel-op every major muscle group of the body. Whetheryour goal is to tone your body, build dramatic musclesize and strength, or improv...

Page 5 - Frame Assembly; ASSEMBLY

5 1 3 4 79 79 51 51 14 1 5 1. Attach a Stabilizer Foot (51) to the Stabilizer (5)with two #8 x 3/4” Screws (56). Attach anotherStabilizer Foot in the same manner. Press two 2” x 3” Inner Caps (79) into the Base(4). Insert two 5/16” x 2 3/4” Carriage Bolts (14) upthrough the Stabilizer (5). Insert tw...

Page 7 - Arm Assembly

7 6. Press two 1” x 7/8” Plastic Bushings (75) onto thewelded spacers on the Press Frame (17). Slidethe Press Frame into place on the Base (4) asshown. Note: This will be a tight fit. The PlasticBushings should fit onto each end of the indi-cated tube in the Base. Lubricate the 3/8” x 8” Bolt (59) w...

Page 8 - Cable Assembly

8 8. Identify the Right Arm (48) and the Left Arm (47)by the position of the welded bracket on each Arm. Press a 2” Round Inner Cap (33) into the lowerend of the Left Arm (47). Wet the end of the Armwith soapy water and slide a 10” Pad (45) onto it.Make sure the 1 1/8” x 2 1/2” Plastic Bushing (74)i...

Page 11 - Seat Assembly

11 19 23 Bracket 15 12 21 55 21 41 10 10 43 43 23 3 72 63 10 2 67 42 20 19. Note: The 3 1/2” Pulley (15) in this step has been preassembled. It is shown exploded inthis drawing for clarity. Route the Long Cable (23) over a 3 1/2” Pulley(15). Make sure that the Cable Trap (66) is ori-ented to hold th...

Page 13 - ADJUSTMENTS

13 26. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginning below. Before using the weight system, pull each cable a few times to make sure that the cables move smoothlyover the pulleys. If one of the cables does not move s...

Page 15 - WEIGHT RESISTANCE CHART

15 WEIGHT PRESS ARM BUTTERFLY ARM LEG LEVER HIGH PULLEY LOW PULLEY PLATES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) Top 20 10 15 14 24 1 45 22 36 28 54 2 70 33 54 44 82 3 99 42 75 60 115 4 128 48 96 72 147 5 153 60 115 90 175 6 184 69 137 103 209 This chart shows the approximate weight resistance at each s...

Page 16 - TROUBLESHOOTING

16 TROUBLESHOOTING Inspect and tighten all parts each time the weight system is used. Replace any worn parts immediately. Theweight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weightsy...

Page 17 - CABLE DIAGRAMS

CABLE DIAGRAMS 17 The cable diagrams show the proper routing of theLong Cable (23) and the Short Cable (58). Use thediagram to make sure that the two cables and thecable traps have been assembled correctly. If thecables have not been correctly routed, the weightsystem will not function properly and ...

Page 18 - EXERCISE GUIDELINES

18 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS MUSCLE BUILDINGTo increase the size and strength of your muscles,push them close to their maximum capacity. Your mus-cles will continually adapt and grow as you progres-sively increase the intensity of your exercise. You canadjust the intensity...

Weider Pro 2250 - Manual

Table of Contents:

Summary

Other Weider Models