VocoPro 8800 - Manual
VocoPro 8800 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CDG-9000PRO remote unit to the player unit.; MAKE SURE ALL PRODUCTS ARE POWERED OFF
- Page 3 – You have the option of either connecting each deck of the; to the AV1 and; RCA; Connect the L/R SWITCHED audio and SWITCHED video outputs on the
- Page 4 – You can either run the; UHF-5800 wireless microphones; Speakers 1 and 2
Club 8800
Quick Reference Setup Guide
This quick reference guide is provided to help you set up your
CLUB-
8800
system for the first time. It contains instructions on setting up
the products that are included in the
CLUB-8800
. If you are connect-
ing any additional gear that is not included in the
CLUB-8800
, refer to
the appropriate manuals for detailed instructions.
Gathering Package Contents
The first step to putting together your new CLUB system is unpacking all of the necessary equipment. Remember to keep
your manuals nearby when setting up, as you may need to reference them. The products listed below are included in the
CLUB-8800 system:
Mounting components into the CLUB-8800
Follow these basic guidelines when mounting:
• Always screw in the mounting screws using an
“X” formation.
• If possible, to keep the products cooler, leave some
space in between the components in the rack.
CDG 9000 PRO CONTROLLER
UHF 5800
VSP M1
KJ 7800 PRO
CDG 9000 PRO PLAYER
VP 2100
Below is one way to configure your CLUB-8800:
CDG-9000PRO
• (2) RCA cables
• (2) Control interface connector
wires
• (1) Instruction manual
KJM-7800PRO
• (1) Instruction manual
VP-2100PRO
• (1) Instruction manual
VX-15 Speakers
• (4) VX-15 speakers
UHF-5800
• (1) 3 ft. male/male ¼” cable
VSP-M1 Multi-Effect Digital Signal
Processor/Mixer
• (1) Instruction manual
SS-88 Speaker Stand
• (4) SS-88 speaker stands
Road Case
• (1) CLUB-8 road case
• (1) Rolling cart
• (2) MK 38PRO microphones
• (1) Gooseneck DJ light
• (1) Double RCA to ¼” cable (3’3”)
• Rack-mounting screws
On the web at
www.vocopro.com
or call toll free
1-800-678-5348
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Setup each SS-88 speaker stand by extending the support lefts to a position that is stable and tighten the tension mechanism firmly. Place a VX-15 speaker on top of the SS-88 so that the shaft of the SS-88 fits flush into the mounting cavity on the bottom of the VX-15 . NOTE: Each end of the SS-88 p...
Using the paired 3’3” RCA to ¼” cable (included):1. Connect the RCA ends to the L/R unbalanced master outputs labeled UNBAL on the rear panel of the KJ-7800PRO . 2. Connect the ¼” ends to the CHANNEL 1 and CHANNEL 2 ¼” inputs on the rear panel of the VP-2100 . You have the option of either connectin...
remote key control You can either run the UHF-5800 mics through the VSP-M1 or go straight into the KJ-7800PRO mixer. Using either a pair of XLR(f) to XLR(m) or XLR(f) to ¼” cables:1. Connect the XLR(f) end to the LEFT BALANCED OUPUT on the rear panel of the VSP-M1 . 2. Now connect the XLR(m) or ¼” e...
