Vector 6SE70 VC - Manual

Vector 6SE70 VC

Vector 6SE70 VC – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
Page: / 57

Table of Contents:

  • Page 2 – for any recommendations or suggestions.
  • Page 3 – Operating Instructions; detailed Operating Instructions; Operating Instruction.
  • Page 5 – Power Section Defintion
  • Page 7 – Power Section Definition; Return to Parameter Menu
  • Page 10 – DC
  • Page 17 – Basic Start-up without Motor Connected to Load; Select “Drive Settings”
  • Page 20 – Connect External Wiring as connection diagram.; Internal Connections
  • Page 23 – Additional Connection for +15 Vdc Encoder.
  • Page 24 – Vector Control without Encoder Feedback; Wait
  • Page 31 – Communication Board Configuration; SLB Telegram Failure Time; Automatic number of; Enter Number of Channels
  • Page 33 – Power Section Defintion
  • Page 35 – Power Section Definition
  • Page 36 – Rated DC Output Current in Amps In[A]; PWE
  • Page 46 – P571=0 Selects Autotransformer
  • Page 51 – Select Trigger Channel
  • Page 52 – Zoom X 2; is
  • Page 53 – Observe Status Message
  • Page 54 – Select Data Trace; to
  • Page 57 – Conditions that would merit re-tuning the drive; If the carrier frequency of P340 is adjusted in multiples that re-
Loading the manual

DROM-02069

Quick Startup Guide for

SIMOVERT MASTERDRIVES

6SE70 VC

Vector Control

Section 1:

Parameterization of Base Drive

Section 2:

Parameterization of Rectifier

Section 3:

Simovis Trace Setup Method

Section 4:

When Should a Drive be re-Tuned

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - for any recommendations or suggestions.

Page 2 Version 1.0 March 1, 2000 We reserve the right to modify functions, technical data, standards, drawings and parameters. We have checked the contents of this document to ensure that they coincide with the described hardware and software. However, deviations cannot be completely ruled-out, so w...

Page 3 - Operating Instructions; detailed Operating Instructions; Operating Instruction.

Version 1.0 March 1, 2000 Page 3 Note: This Quick Startup Guide is not an autonomous document, but is intended to direct users tothe section in the Operating Instructions which are important for start-up. Thus, these brief instructions can only be completely valid when used in conjunction with the O...

Page 5 - Power Section Defintion

Version 1.0 March 1, 2000 Page 5 Section 1: Parameterization of Base Unit SIMOVERT MASTERDRIVES 6SE70 VC Vector Control 1.1 Power Section Defintion 1.2 Factory Reset 1.3 Basic Start-up 1.3.1 Volts/Hz without encoder feedback1.3.2 Volts/Hz with encoder feedback1.3.3 Vector Control without encoder fee...

Other Vector Models

All Vector Other