URC KP-4000 - Manual

Network Requirements and Power Options The KP-4000 must be connected to the same Local Area Network asthe MRX-1 to function correctly. Additionally, in order for yourclient to enjoy internet features such as RSS feeds, the Local AreaNetwork must be connected to the Internet. You have three options t...

KP-4000 N ETWORK K EYPAD Page 4 Option 2: PoE Injector KP-4000 KP-4000 Router PoE Injector(not included) Power Supply(not included) 1. Splice a 12V 1Amp Power Adapter (not included) and connect to the rear Power input. 2. For network connections to IP devices, MRX-1 and the internet, connect a CAT 5...

Page 5 KP-4000 N ETWORK K EYPAD 12V Power (not required in a PoEinstallation) LAN PoE RJ-45 (Connects KP-4000 to Network) IR OUT/RFTX-1 (only required if URC RF Lighting, RF Base or a wired emitter is needed) Installation Notes MAC Address Labels/Reset Button The KP-4000 has a magnetic cover, simply...

IR OUT/RFTX-1 This 3 Conductor removable connector can be used for either anRFTX-1 RF transmitter or for a URC IR emitter. RFTX-1 Connections In installations with URC RF lighting or a standard RF base station,you will need to add an RFTX-1 RF Transmitter to the KP-4000.Range can wildly vary, depend...

Page 8 KP-4000 N ETWORK K EYPAD 1. The KP-4000 installs in a standard two gang box. If in a retrofit installation, cut in and install a standard two gang p-ring or retrofit box (not included) into the wall. 2. Make connections for IR Out/RFTX-1, LAN, or Power Supply. For connections, refer to page 5...

Page 9 CCP MAC Address Discovery 1.Once the KP-4000 has been connected to the network, notate the MAC address located on the KP-4000 under the magnetic coverplate. 2. Open the Complete Control Program editor. 3. Select the Program tab then press Configure Home. 4. Add a KP-4000 Network Keypad from t...

Page 10 KP-4000 N ETWORK K EYPAD Displaying the Settings Screen You can adjust the settings of the KP-4000 whenever you like by pressingand holding both the MAIN and MUTEbuttons for five seconds. When you do,the screen will change to the SETTINGSscreen. If you do not press any button onthe SETTINGS ...

Page 11 KP-4000 N ETWORK K EYPAD Sound Your KP-4000 may have been pro-grammed to make sounds. This is option-al, and some professional installers may prefer to keep it silent.However, you can adjust the volume toany level you like by touching and dragging the volume control here. Adjusting Brightnes...

Page 13 KP-4000 N ETWORK K EYPAD Frequently Asked Questions I am unable to control my URC Lighting Dimmer/Switch with theKP-4000. Now what?Make sure the RF switch on the RFTX-1 is set to the correct fre-quency for the URC Dimmer or Switch. URC Lighting ModelsMRFA is 418MHz and MRFB is 433MHz. How do...

Page 14 USA Limited Warranty Statement Your Universal Remote Control, when delivered to you in newcondition, is warranted against defects in materials or work-manship as follows: UNIVERSAL REMOTE CONTROL, INC.warrants this product against defects in material or workman-ship for a period of one (1) y...

Page 15 Federal Communication Commission InterferenceStatement This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmful interference in a residential...