Page 2 - FCC Certifications; Reorient or relocate the receiving antenna.
FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, u...
Page 3 - TABLE OF CONTENT
TABLE OF CONTENT INTROUCTION....................................................................................................................................... 1 S AMPLE A PPLICATION ....................................................................................................................
Page 5 - Small Office / Home Users; ISP; Figure 1: Small Office/ Home Office Setup
- 1 - INTROUCTION IP Share device is designed for IP address simplification and conservation, as it enables private IP Internet works that use non-registered IP addresses to connect to the Internet. It usually connects two networks together, and translates the private (not globally unique) addresses...
Page 6 - LED Indicators on the Front Panel; Figure 2: LED Indicators and Ports
- 2 - Features ?? Supports PPPoE. ?? Supports VPN.(PPTP pass through). ?? Explicit LED indication for Internet connection. ?? Supports Internet applications such as Web, ICQ, FTP, Telnet, E-Mail, News, NetMeeting, PCAnyWhere, mIRC , CuSeeMe, AoE,… ?? Natural firewall keeps hackers out. ?? DHCP serve...
Page 8 - System Requirements; This product's GUI setup interface requires
- 4 - System Requirements Your system must meet the following requirements to use the product’s Setup program. If you are using a Unix or apple based system, telnet should be used t o configure the product. This product's GUI setup interface requires 1. Windows 95, 98, ME, NT or 2000. 2. IE4.01 or a...
Page 9 - then you are; Local and Global Port Addresses; Enabled; Information from ISP; If your IP address is provided
- 5 - FACTORY DEFAULT SETTINGS Password The default setting for password has been left blank in the factory. Press Enter then you are logged in for the first time. It is recommended that you set a password for security and management purpose. If you ever forget the password to log in, you can only r...
Page 10 - How to start; For the first time installation, in Windows, run; Figure 3; When the setup program is installed, go to; Start; When the opening screen appears, click; Find; to find the device you want to configure.
- 6 - CONFIGURATION The product can be configured through the setup program (included in the package), through a terminal emulation program, such as Windows HyperTerminal, or through Telnet. The product can be set with a range of options to allow it to function in most any network environment. Confi...
Page 11 - Figure 5; Select the device that you would like to setup and then click; Configure; The; configure; Management; Figure 7
- 7 - Figure 5 Select the device that you would like to setup and then click Configure . Figure 6 The configure dialog box is categorized into several tabs as shown in the following. Management Figure 7
Page 13 - Local Port
- 9 - TELNET management… : Checking this item lets you manage this devic e remotely from outside of the network through Telnet. ?? Default: disabled. Local Port This screen contains settings for LAN interface attached to the local network. Figure 8 IP Address ?? Default: 192.168.1.254 SubNetmask ?? ...
Page 14 - Global Port; If it is checked, the Global port IP address is
- 10 - Continuous IP address pool starts at The starting address of this local IP network address pool. The pool is a piece of continous IP address segment. Number of IP address in pool ?? Maximum: 128 . Default: 128 Global Port This screen contains settings for the Global interface toward Internet....
Page 15 - SubNetmask; These values will be automatically provided once; Obtain global port configuration automatically; ”. You can change the values if; Virtual Server; Single Port/Port Range
- 11 - SubNetmask 4 : Provided by our ISP. Gateway/DNS server #1/DNS server #2: These values will be automatically provided once you clic k “ Obtain global port configuration automatically ”. You can change the values if necessary. Virtual Server Being a natural Internet firewall, this IP Sharing de...
Page 16 - Packet Filters
- 12 - Figure 11 Port Type : please select the port type (TCP or UDP) for the port number that was entered earlier. Note: Maximum 12 Server Entries is allowed. Each port number can only be assigned to one IP address. Packet Filters In the Packet Filters setup screen, you can block specific internal ...
Page 17 - Network Adapter Address Filter:; local
- 13 - Figure 12 Network Adapter Address Filter: Filter according to local computer’s network adapter MAC address. Figure 13 Network Adapter’s MAC address consists of 12 alphanumeric characters (i.e. 00 ab 12 cd 34 ef) and it is normally printed on a sticker on the network adapter. If you have Windo...
Page 19 - Configuration in Terminal Program Mode; How to start HyperTerminal
- 15 - Configuration in Terminal Program Mode You can use terminal emulation on your PC/workstation for the initial and future configuration of your product. Windows HyperTerminal or other terminal emulation applications can be used. If you prefer, a telnet session can be opened directly. Telnet pro...
Page 20 - Figure 18: COM 1 Properties; Power up the product.; How to start Telnet; Go to; Type “; OK; . If the local port’s IP address was set
- 16 - Figure 18: COM 1 Properties 8. Power up the product. How to start Telnet 1. The instructions below are for using this unit at its default settings (i.e. DHCP enabled, Local Port IP address: 192.168.1.254, Subnet: 255.255.255.0). 2. Go to Start ? Run . Figure 19 3. Type “ telnet 192.168.1.254 ...
Page 21 - Starting the Configuration; Administrator password:; Terminal Commands
- 17 - 333 Figure 20 Starting the Configuration 1. Once the connection is made successfully either via HyperTerminal or Telnet, the following information will appear, Dual Ethernet IP Share for Cable/xDSL Modem, version X.XX Administrator password: 2. No password is required the first time you log i...
Page 22 - TERMINAL COMMAND; Type; passwd; No password is required when logging in for the first time.
- 18 - TERMINAL COMMAND Type ? or help to list the main menu commands as below. command>help Dual Ethernet IP Share for Cable/xDSL Modem, version X.XX ======================================================= Command Description ------------------------------------------------------- help Show this...
Page 23 - and hit “Enter” to enter the password setup screen.; show; Factory Default Setting
- 19 - ?? At command>, type in passwd and hit “Enter” to enter the password setup screen. ?? Password can be up to six characters long. ?? Password can contain letters, numbers, and spaces. ?? Password is case sensitive. ?? To set or change your password, key in up to six characters and hit “Ente...
Page 24 - set; After executing the; s e t; Press; Enter
- 20 - Obtain global port configuration from ISP : [Yes] .. under claiming IP address of global port : [0.0.0.0] SubNetmask of global port : [0.0.0.0] Device name : [Untitled] Domain name : [Domain] Gateway : [0.0.0.0] Primary DNS server : [0.0.0.0] Secondary DNS server : [0.0.0.0] set After executi...
Page 25 - New configuration will be:; vserv; Natural
- 21 - SubNetmask of global port [0.0.0.0] : Device name (0 to 20 characters) [Untitled] : Domain name (0 to 36 characters) [Domain] : Gateway [0.0.0.0] : Primary DNS server [0.0.0.0] : Secondary DNS server [0.0.0.0] : New configuration will be: IP address of local port : [192.168.1.254] SubNetmask ...
Page 26 - There are four operation choices for; Add a virtual server; Table 5; release; renew; ” command as described below to retrieve configurations.
- 22 - Internet to the local network are blocked. Computers outside the Intranet are allowed to access specific ports by using the vserv command. There are four operation choices for vserv command: 1) Show, 2) Add, 3) Del, 0) Quit. Example: command>vserv Set local virtual server mapping (maximum ...
Page 27 - Give up the obtained global port configuration; Update global port configuration; user; Example; IP address Node address Remainder time Host name
- 23 - command>release Give up the obtained global port configuration Note: if you choose NOT to obtain the global port configuration from your ISP, this command won’t be executed and the following message will appear. command>release Works only if 'Obtain global port configuration from ISP' i...
Page 28 - Ping; ping; and then the; IP address; that you wish to detect. If; session; List active Internet sessions through this device.
- 24 - 192.168.10.4 0080-C8F8-8A64 2:55:48 Victoria 192.168.10.5 0080-C8F8-8A64 expired SNL Total 5 user, 3 active lease. Elapsed 0:01:03 Ping Ping is a basic Internet program that lets you verify that a particular IP address exists and can accept requests. At command> type in ping and then the I...
Page 29 - filter; or; MAC address filter:; add a new filter
- 25 - tcp 7 192.168.10.31 1033 4138 211.75.84.154 80 0 GERNERAL tcp 7 192.168.10.32 1729 4139 140.113.39.195 110 0 GERNERAL tcp 7 192.168.10.27 1063 4140 210.66.41.132 110 0 GERNERAL udp 1 192.168.10.31 1028 16385 168.95.192.1 53 20 GERNERAL udp 1 192.168.10.32 1726 16386 168.95.1.1 53 5 GERNERAL u...
Page 30 - Item Type Action From To; Example 1; filter on IP
- 26 - Item Type Action From To ==== ====== ======= ================ ================ 1. MAC Filter 0080C8123456 IP address filter: Example 1 : Set IP address filter to allow those local computers with IP address fro m 192.168.0.25 to 192.168.0.32 to access Internet. Operations => 1)Show 2)Add 3)...
Page 31 - Port Filter; Example 1: Allow users to access Web service only.; filter on server service
- 27 - With the combination of the above two filter examples, the workstations with IP address 192.168.0.25, 192.168.0.26, 192.168.0.27, … and 192.168.0.32 can access the Internet via the Internet Router, but none of the workstations can access the 203.66.99.100 Web Server (web site). Port Filter Ex...
Page 32 - NewFirmware
- 28 - FIRMWARE UPGRADE System Requirements ?? One free COM port on PC. ?? A pin -to-pin RS-232 cable . One end is 9 pin male connector, the other end is 9 or 25 pin female connector depends on the COM port. ?? FWLOAD.EXE : This is an auxiliary program for firmware upload. ?? FIRMWARE.BIN : This is ...
Page 35 - Start this device by running; Configuration; Check “Change Administrator’s Password.; Using Terminal Mode; Refer to the previous section titled “; Configuration in Terminal Program; ” for terminal
- 31 - CHANGING PASSWORD The device has no password at default. It is recommended that you change the default passwords to ensure that someone cannot adjust the devices settings. Using GUI 1. Start this device by running setup.exe as described in the chapter titled “ Configuration ”. 2. Check “Chang...
Page 36 - Forgot y our password?; Refer to; FAQ; section for “Factory Reset” procedures.
- 32 - Note: In default, there is no password, so just leave this entry blank and hit “Enter” to continue. type new password (0 to 6 characters) : ****** Type in the new password and press <Enter> re-type new password (0 to 6 characters) : ****** Re-type the new password and press <Enter>...
Page 37 - For GUI Setup program; Note
- 33 - PPP OVER ETHERNET (P PPOE) What is PPPoE? PPPoE is known as a dial-up DSL service. It is designed to integrate the broadband services into the current widely deployed, easy-to-use, and low-cost dial-up-access networking infrastructure. Thus, customer can get greater access speed without chang...
Page 38 - The fctory default values is detailed in the section; Factory Default Settings; “I can't find the product using the GUI Setup Software”; Configuration in GUI; . Also, the computer should be restarted to ensure that it is
- 34 - FAQ Factory Reset If for any reason, e.g. password being forgotten, you have to reset this device to factory default settings. By performing the Factory Reset, the current settings will be lost and the settings are reseted to default. The fctory default values is detailed in the section Facto...
Page 39 - IP address conflict; winipcfg; My Internet application won't work; Some applications that may be affected are
- 35 - addresses on a LAN with an existing DHCP server may cause problems throughout a network. It is recommended you disable other DHCP serves on the network if you plan on using this product on the network. IP address conflict When you see the message box prompted for IP address conflict, this mea...
Page 42 - Can not access the Internet; Identification
- 38 - F. Press Save. Wait 30 seconds for the device to reboot and then try the application again. It may be necessary to restart your application or your computer for the application to recognize the change. Can not access the Internet For Cable Modem users, find the workstation’s “Computer” name a...
Page 44 - Diagnosis; TCP/IP Network Diagnosis; Execute; and click; Click the; More Info; button to get detailed configuration information.
- 40 - Diagnosis TCP/IP Network Diagnosis Execute WINIPCFG.EXE or PING.EXE for TCP/IP network diagnosis. WINIPCFG The WINIPCFG program (for Win 95, 98, and 98Me) is used to gather information about the TCP/IP connections that are active on your system. It cannot be used to dynamically adjust TCP/IP ...
Page 45 - Figure 35: IP Configuration; ) The Client should have an IP address within the pres cribed range.
- 41 - Figure 35: IP Configuration On the top, the “Host Name” and “DNS server” of the computer are configured to call when it is looking for a named resource. The default gateway is the server through which the client connects to the Internet. The DHCP Server identifies the network server that assi...
Page 46 - and; ISP Connectivity Checkup; these settings via the Windows GUI.; Internet Connectivity Checkup
- 42 - For example, to find the server 168.95.192.1, type the following command at the MS-DOS prompt: C:\>ping 168.95.192.1 . PING can be executed in Windows as shown below: 1. Go to the Start menu. 2. Click Run . 3. Type ping 168.95.192.1 and click OK . 4. The server (IP address) is online if th...
Page 47 - Getting Technical Support; You can also contact us for technical support.
- 43 - Getting Technical Support You can also contact us for technical support. TRENDware www.trendware.com E-mail: [email protected] Phone: 310-891-1100
Page 48 - APPENDIX A SPECIFICATIONS; via direct serial cable connection through Console port
- 44 - APPENDIX A SPECIFICATIONS Protocols IP, NAT, ARP, ICMP, DHCP Management/Setup Locally, via direct serial cable connection through Console port Options Locally, via GUI for Windows 95/98/NT Remotely via Telnet (needs to enabled this function via GUI ) Local Port RJ-45, 10/100 Dual Speed Ethern...
Page 49 - APPENDIX B SUPPORTED INTERNET APPLICATIO NS; Application
- 45 - APPENDIX B SUPPORTED INTERNET APPLICATIO NS Application Setti ngs for Outgoing Connection Setting for Incoming connection ICQ98a,99b None None Netmeeting 2.1 & 3.0 None 1503(tcp) 1720(tcp) AOE 2300-2400(tcp) 2300-2400(udp) 47624(tcp) 2300-2400(tcp) 2300-2400(udp) 47624(tcp) VDO Live None ...
