Transition Networks SISTM10XX-162-LR - Manual

2 Package Contents Please refer to the package content list below to verify them against the checklist. • SISTM10xx-162-LRx Managed Industrial Switch • DC Jack 2.0/150mm RoHS • User manual CD • DIN-Rail Bracket (attached on the switch) • One wall mount plate and six screws SISTM10xx-162-LRx DC Jack ...

3 Hardware Description In this paragraph, it will describe the Industrial switch’s hardware spec, port, cabling information, and wiring installation. Physical Dimension 54mm (w) x 135mm (h) x 105mm (d) Front Panel The Front Panel of the SISTM10xx-162-LRx Managed Industrial Switch is shown below: Res...

4 set all configurations back to default setting Bottom View The bottom view of the switch is shown below: DIP-switch The switch provides the 9 DIP-switch for configuring the relay alarm operation mode and the master ring operation mode. The default value of Dipswitch is OFF . DIP Switch No Status D...

6 Off No power inputs Yellow Power failure or UTP port failure or Fiber port failure Fault Off No Power failure or UTP port failure or Fiber port failure occurs Green The industrial switch is the master of X-Ring group R.M. (Ring Master) Off The industrial switch is not a ring master in X- Ring grou...

7 All ports on this industrial switch support automatic MDI/MDI-X operation, user can use straight- through cables (See figure below) for all network connections to PCs or servers, or to other switches or hubs. In straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are connected st...

9 Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as below figure shows. By inserting the wires and set the DIP switch at “ ON ” status, it will detect the fault status which the power is failure or port link failure and form an open circuit. And, ...

10 Mounting Installation DIN-Rail Mounting The DIN-Rail is screwed on the industrial switch when out of factory. 1. First, insert the top of DIN-Rail into the track. 2. Then, lightly push the DIN-Rail into the track.

11 3. Check the DIN-Rail is tightly on the track. 4. To remove the industrial switch from the track, reverse steps above. Wall Mount Plate Mounting Follow the below steps to mount the industrial switch with wall mount plate. 1. Remove the DIN-Rail from the industrial switch; loose the screws to remo...

12 Hardware Installation Installation Steps 1. Unpacking the Industrial switch 2. Check the DIN-Rail is screwed on the Industrial switch. If the DIN-Rail is not screwed on the Industrial switch. Please refer to DIN-Rail Mounting section for DIN-Rail installation. If user want to wall mount the Indus...

13 Network Application This chapter provides some sample applications to help user to have more actual idea of industrial switch function application. A sample application of the industrial switch is as below:

17 Home Interface Port status View every port status that depended on user’s setting and the negotiation result • Port: The port number • Type: The speed mode, ex: 100TX = 100Mbps • Link: “Down” means “No Link”. “UP” is for “Link” • State: Display port statuses “disable” or “enable”. “Unlink” will b...

18 Single Port Information Click the port on the Panel figure on the web interface directly. Then, the single port information window will show up and display the port current information. Port information interface Port Statistics The following information provides the current port statistic inform...

19 Port Control Change the port status • Select the port by scroll the Port column • State: Disable or enable control of this port • Negotiation: Set auto negotiation mode is Auto, Nway (specify the speed/duplex on this port and enable auto-negotiation), or Force • Speed: Set the speed of the port •...

20 • Hardware version: Display the switch hardware version • MAC Address: Display the unique hardware address assigned by manufacturer (default) Switch settings interface [NOTE] Remember to execute the “Save Configuration” action, otherwise the new configuration will lose when switch power off. Port...

21 Port Mirroring interface [NOTE] 1. Select the monitor mode as disable to disable the mirroring 2. Remember to execute the “Save Configuration” action, otherwise the new configuration will lose when switch power off. VLAN configuration A Virtual LAN (VLAN) is a logical network grouping that limits...

22 VLAN Configuration interface Port-based VLAN Packets can go among only members of the same VLAN group. Note all unselected ports are treated as belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is ignored. In order for an end station to send packets to different V...

24 802.1Q VLAN Tagged-based VLAN is an IEEE 802.1Q specification standard which it allows to create a VLAN across devices from different switch venders. IEEE 802.1Q VLAN uses a technique to insert a “tag” into the Ethernet frames. Tag contains a VLAN Identifier (VID) that indicates the VLAN numbers....

25 • Grouping the ports and click Add button 802.1q VLAN –Add interface • And then, click Next then follow interface as below.

26 Click Apply to set the outgoing frames are VLAN-Tagged frames or untagged Tag: Outgoing frames with VLAN-Tagged Untag: Outgoing frames without VLAN-Tagged Port VLAN ID • Configure port VID settings • Port VLAN ID: Enter the port VLAN ID • And then, click Apply • To reset back to default value, cl...

27 Alert There are three kinds of alert – e-mail, event, and power alarm for user to configure. Email Alert Configuration When the specific events occur, the system will send the alert to the email account that is assigned by user. User can set up the mail server IP, mail account, and forwarded emai...

29 Power Alarm Configuration Power alarm function enables the Relay alarm action. Without enabling power alarm function, the Relay alarm action will not work even the Relay alarm is set. • Mark the check box and click Apply button Power Alarm interface IP Configuration User can configure the IP Sett...

30 IP configuration interface SNTP Configuration User can configure the SNTP (Simple Network Time Protocol) settings. The SNTP allows user to synchronize switch clocks in the Internet. • SNTP Client: To enable or disable SNTP function to get the time from the SNTP server • Daylight Saving Time: To e...

32 IP Security IP security function allows user to assign 10 specific IP addresses that have permission to access the switch through the web browser for the securing switch management. • Enable the IP Security: Mark the check box to enable the IP security function • Security IP 1 ~ 10: Assign up to ...

34 RSTP– System Configuration Interface Per Port Configuration Configure path cost and priority of every port • Select the port in Port column • Path Cost: The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200000000 • Priority: Dec...

35 RSTP – Per Port Configuration interface X-Ring X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is similar with STP or RSTP, but the algorithms not the same. In the X-Ring topology, every switch should enable X-Ring function and assign two member ports in the ri...

37 QoS Configuration Configure Qos setting of the every port • Oos Policy: Select the Qos policy rule Using the 8,4,2,1 weight fair queue scheme: The switch will follow 8:4:2:1 rate to process priority queue from Hi to lowest queue. For example: the system will process 8 high queue packets, 4 middle...

38 QoS configuration Interface IGMP The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect IGMP queries and report packet...

39 Message Description Query A message sent from the querier (IGMP router or switch) asking for a response from each host belonging to the multicast group. Report A message sent by a host to the querier to indicate that the host wants to be or is a member of a given group indicated in the report mes...

40 4. And then, click Apply Security Manager interface [NOTE] Remember to execute the “Save Configuration” action, otherwise the new configuration will lose when switch power off. SNMP Configuration The SNMP is a Protocol that governs the transfer of information between management and agent. The swi...

41 System Options • Name: Enter a name for the switch • Location: Enter the switch physical location • Contact: Enter the name of contact person or organization Community strings Serve as a password. • Strings: Key in the name of string • RO: Read only. Enables requests accompanied by this string to...

42 TFTP Restore Configuration interface TFTP Backup Configuration User can save current flash ROM value from the industrial switch to the TFTP server, then go to the TFTP restore configuration page to restore the image value back to the industrial switch. • TFTP Server IP Address: Key in the TFTP se...

44 Save Configuration Save the industrial switch configuration to the flash memory. Power off the industrial switch without the saving, all changed configuration will lost. • Click the Save Flas h button the save the configuration Save Configuration Interface Rate Control Set up every port’s bandwid...

45 Rate Control Interface [NOTE] 1. Remember to execute the “Save Configuration” action, otherwise the new configuration will lose when switch power off. 2. Qos and Rate control cannot be existed at the same. System Log Set up system log events and view the system log events System Log Configuration...

46 System Log Configuration interface Event Configuration User can select the system log events. W hen selected events occur, the system will send out the log information. Also, per port log events can be selected. • System event selection: 4 selections – Device cold start, Power status, SNMP Authen...

48 Troubles shooting • Verify that is using the right power cord/adapter (DC 12-48V), please don’t use the power adapter with DC output bigger than 48V, or it will burn this converter down. • Select the proper UTP cable to construct user network. Please check that is using the right cable. use unshi...

49 Technical Specification Standard IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX and 100Base-FX Fast Ethernet IEEE802.3x Flow Control and Back-pressure IEEE802.1d spanning tree / IEEE802.1w rapid spanning tree IEEE802.1p class of service IEEE802.1Q VLAN Tag Protocol CSMA/CD Management SNMP ma...