Page 2 - COPYRIGHT & TRADEMARKS; Specifications are subject to change without notice.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form ...
Page 3 - FCC STATEMENT; Reorient or relocate the receiving antenna.; FCC RF Radiation Exposure Statement
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses a...
Page 4 - which case the user may be required to take adequate measures.; National Restrictions; Country; Note: Please don’t use the product outdoors in France.; Canadian Compliance Statement; successful communication.
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive...
Page 6 - Safety Information
Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make r...
Page 7 - DE CLA R AT ION OF CONFOR M IT Y; Arche r; The product carries the CE Mark:
TP-LINK TECHNOLOGIES CO., LTD DE CLA R AT ION OF CONFOR M IT Y For the following equipment: Product Description: AC1900 Wireless Dual Band Gigabit ADSL2+ Modem Router Model No.: Arche r D9 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical re...
Page 8 - CONTENTS
CONTENTS Package Contents ................................................................................................................ 1 Chapter 1. Product Overview ............................................................................................ 2 1.1 Overview of the Modem Router ......
Page 12 - Package Contents
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Package Contents The following contents should be found in your package: One Archer D9 AC1900 Wireless Dual Band Gigabit ADSL2+ Modem Router One Power Adapter for Archer D9 AC1900 Wireless Dual Band Gigabit ADSL2+ M...
Page 13 - Chapter 1. Product Overview; Thank you for choosing the; Overview of the Modem Router; modem router’s functions.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Chapter 1. Product Overview Thank you for choosing the Arche r D9 AC1900 Wire less Dual Band Gigabit ADSL2+ M ode m Route r . 1.1 Overview of the Modem Router The Archer D9 AC1900 Wireless Dual Band Gigabit ADSL2+ Modem...
Page 16 - service is available now.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide (Internet) On The network is available with a successful Internet connection. Off There is no successful Internet connection or the modem router is operating in Bridge mode. Please refer to Note 2 for troubleshooting. (...
Page 17 - AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide; Modem Router
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide 1.3.2 The Back Panel Figure 1-2 The following parts are located on the rear panel (View from left to right). ADSL : Through the port, you can connect the telephone to the modem router. Or you can connect them by an ex...
Page 18 - : Restore the default setting from
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Method one : With the modem router powered on, use a pin to press and hold the RESET button for at least 8-10 seconds. And the modem router will reboot to its factory default settings. Method two : Restore the default s...
Page 19 - Chapter 2. Connecting the Modem Router; System Requirements; Method two; • LINE: Connect to the
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Chapter 2. Connecting the Modem Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet). PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. TCP/IP protoco...
Page 21 - Chapter 3. Quick Installation Guide; Troubleshooting
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Chapter 3. Quick Installation Guide This chapter will show you ho w to configure the basic functions of your Archer D9 AC1900 Wireless Dual Band Gigabit ADSL2+ Modem Router using Quick Se tup Wizard within minutes. 3.1 ...
Page 22 - Quick Installation Guide; which are needed for PPP connections.; Tools; menu; Internet Options; , in the screen that; OK
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC corre ct? If the router's IP address is 192.168.1.1, your PC's IP address mus...
Page 24 - On this page, please confirm all parameters. Click; Save; and wait a moment for your
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 3-7 Step 7. Configure the basic parameters for 2.4GHz wireless network, and then click Ne xt . Figure 3-8 Step 8. Configure the basic parameters for 5GHz wireless network and then click Ne xt . Figure 3-9 Step 9....
Page 25 - You will see the; Comple te; screen below. Click; Finish; to complete these settings.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 3-10 Step 10. You will see the Comple te screen below. Click Finish to complete these settings. Figure 3-11 The basic settings for your modem router are completed. Please open the web browser and try to log on to...
Page 26 - Chapter 4. Configuring the Modem Router
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Chapter 4. Configuring the Modem Router This chapter will show configuration for the key functions on the Web-based management page. 4.1 Login After your successful login, you will see the twenty-three main menus on the...
Page 27 - Choose “
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide 4.2 Status Choose “ Status ”, you can see the corresponding information about Device Information , DSL , WAN , LAN and Wire le ss . 16
Page 29 - Quick Installation Guide
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide . 4.4 Operation Mode Choose “ Operation M ode ”, and you will see the screen as shown in Figure 4-2. Select your desired mode and then click Sav e . Figure 4-...
Page 30 - Network; ”, and you will see the WAN Port Information Table in the; Add
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide 4.5.1 WAN Settings Choose “ Network ” “ WAN Se ttings ”, and you will see the WAN Port Information Table in the screen similar to Figure 4-3. There are six different configurations for the connection types, which are ...
Page 37 - If your ISP provides an IPoA connection, select; IPoA; option for the; Conne ction Type; on the
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-8 4.5.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the Conne ction Type on the screen. 26
Page 38 - Enter the IP Address and Subnet Mask provided by ISP.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-9 IP Addre ss/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. DNS Se rv e r/Secondary DNS Se rv er: Type in your preferred DNS server. De fault Gate way: Select a WAN Interface from the...
Page 39 - After you finish the Internet configuration, please click; Sav e; to make the settings take effect.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Note : After you finish the Internet configuration, please click Sav e to make the settings take effect. 4.5.2 Interface Grouping Choose “ Network ” “ Interface Grouping ”, you can view all the current groups on thi...
Page 40 - Click; to make the entry effective immediately; ” menu, and you will see the LAN screen (shown in Figure
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-12 Click Sav e to make the entry effective immediately 4.5.3 LAN Settings Choose “ Network ” “ LAN Se ttings ” menu, and you will see the LAN screen (shown in Figure 4-13). Please configure the parameters for...
Page 43 - WAN Settings
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide 4.5.5 MAC Clone Choose menu “ Ne twork ” “ M AC Clone ”, you can configure the MAC address of the WAN Interface as shown below. The WAN Interface List displays the WAN Interfaces you have configured on the section 4.5...
Page 45 - D9 supports up; Add Ne w Conne ction; in Figure 4-21 and then you will enter the screen shown in Figure
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-21 This section will guide you to configure a VPN tunnel between two Archer D9s. The topology is as follows. Note : You could also use other VPN Routers to set VPN tunnels with Archer D9. Archer D9 supports u...
Page 47 - If you want to change the default settings of; Adv anced Se ttings; , please make sure that both VPN; phase 1; and
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Click Show Advanced Se ttings and then you can configure the Advanced Settings. We re comme nd you le ave the Adv anced Se ttings as de fault v alue. Figure 4-23 Mode : Select M ain Mode to configure the standard nego...
Page 49 - Interface Grouping
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-25 Group/ IP Address/ Subne t M ask: Displays group name, IP address and subnet mask. The parameters can be configured on the Interface Grouping page and LAN Settings page. DHCP Se rver: If enabled, the mod...
Page 50 - , the DHCP function will not take effect.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Note : 1) To use the DHCP server function of the modem router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 2) You have to disable NAT of the WAN connections, or the DHC...
Page 52 - in the entry you want to modify the entry.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-29 To add a v e ndor class: 1. Click the Add Ne w button. Then Figure 4-30 will pop up. 2. Enter parameters for the vendor class. Click the Sav e button. Figure 4-30 To modify or de le te an e xisting e ntry: 1...
Page 54 - If; Mode; selecting; Enable SSID Broadcast:
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide 11g only: Select if all of your wireless clients are 802.11g. 11n only: Select only if all of your wireless clients are 802.11n. 11bg mixe d: Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixe...
Page 57 - successfully added to the network.; Wire le ss Se curity
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Step 2: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 3: When the WPS LED is on, the client device has successfully connected to the modem router. Step 4: Refer bac...
Page 59 - The time you set is the period you need the wireless off.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide • Ke y Type : You can select the WEP key length (64-bit, or 128-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit: You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F...
Page 64 - exceed 32 characters.; M ode; Select the desired mode.; below. Make sure the following settings are correct.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-41 SSID: Wireless network name. Enter a desired SSID which is case-sensitive and must not exceed 32 characters. Region: Select your region from the drop-down list. This field specifies the region where the ...
Page 67 - click
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-44 Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then click Conne ct button. Step 3: “ Conne ct succe ssfully ” will appear on the screen of Figure 4-44, which means ...
Page 81 - the changes take effect.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-60 2. Click the Browse button, and then select the Se le ct Volume from the drop-down list. 3. Enter the display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. Yo...
Page 84 - reached to be 6, you can delete a share folder and then add a new one.; Route Settings
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide b) Enter the name of the share folder in Share Name field. c) Click the Apply button to apply the configuration. Figure 4-64 Click the Scan now to scan all the share folders immediately. You can also select the Auto-sca...
Page 90 - page to be any other value except 80 such as 8080.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Syste m Tools –> Manage Control page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. 4.14.2 Port Triggering Choose menu “ Forwarding ” → “ Port Triggeri...
Page 92 - hosts on the LAN will be refused.; Ope n Ports; ranges cannot overlap each other.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Note : 1. When the trigger connection is released, the corresponding opened ports will be closed. 2. Each rule can only be used by one host on the LAN at a time. The trigger connection of other hosts on the LAN will b...
Page 93 - Parental Control
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Current UPnP Status: UPnP can be enabled or disabled by clicking the Enable or Disable button. This feature is enabled by default. Curre nt UPnP Se ttings List: This table displays the current UPnP information. • Ap...
Page 106 - the page will prompt you to delete all the IPv6 WAN connections.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Figure 4-99 WAN Connection: Select a WAN connection from the drop-down list. Only the connected WAN connections can be shown in the drop-down list. Configuration Type : Select a configuration type for this tunnel. A...
Page 107 - Bandwidth Control
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide 4.19 Bandwidth Control Choose menu “ Bandwidth Control ”, and then you can configure the Upstream Band width and Downstream Bandwidth in the next screen. The values you configure should be less than 1000000Kbps. For opt...
Page 118 - Loss of power during the upgrade could damage the modem router.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide 2) When upgrade the modem router's firmware, you may lose its current configurations, so please write down some of your customized settings before upgrading the firmware. 3) Do not turn off the modem router or press the...
Page 120 - Reset the value of the entry to zero.; De le te; Delete the existing entry in the table.; Logout; ”, and you will back to the login screen as shown in Figure 4-119.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Ope ration Re se t Reset the value of the entry to zero. De le te Delete the existing entry in the table. 4.24 Logout Choose “ Logout ”, and you will back to the login screen as shown in Figure 4-119. Figure 4-119 109
Page 121 - Appendix A: Specifications; Ge ne ral; Power
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Appendix A: Specifications Ge ne ral Standards and Protocols ANSI T1.413, ITU G.992.1, ITU G.992.3, ITU G.992.5, IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.11ac, IEEE 802.3, IEEE 802.3u, IEEE802.3a...
Page 122 - Appendix B: Troubleshooting; Note; T2. What can I do if I don’t know or forget my password?
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Appendix B: Troubleshooting T1. How do I restore my modem router’s configuration to its factory default settings? With the modem router powered on, press and hold the RESET button on the side panel for 8 to 10 seconds b...
Page 124 - T4. What can I do if I cannot access the Internet?; cables and power adapter.
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your modem router’s factory default settings ...
Page 125 - Appendix C: Technical Support; Technical Support
Arche r D9 AC1900 Wire le ss Dual Band Gigabit ADSL2+ M ode m Router Use r Guide Appendix C: Technical Support Technical Support For m ore troubles hooting help, go to: http://www.tp-link.com/en/support/faq To download the lates t Firm ware, Driver, Utility and Us er Guide, go to: http://www.tp-...
