Toshiba LF654 - Manual
This Installation Manual covers Toshiba’s electromagnetic flowmeter systems, including the LF654/LF620 series, focusing on their Mount-Anywhere design for versatile fluid measurement. The guide addresses technical specifications such as measurement accuracy, pressure limits, and communication protocols (HART, PROFIBUS, MODBUS), along with installation dimensions, grounding requirements, and environmental safety standards like ASME B16.5 or EN 1092-1. It also details wiring configurations for power, signals, and grounding, emphasizing proper cable management based on fluid conductivity to ensure reliable operation.
Table of Contents:
- Page 1 – Electromagnetic Flowmeter Operation and Specifications
- Page 2 – LF654 Detector Technical Specifications
- Page 3 – Converter Signal and Communication Specifications
- Page 4 – TIC-LF654L Device Features and Reliability
- Page 5 – Combined Flowmeter Installation Dimensions
- Page 6 – TIC-LF654L Dimensional Specifications
- Page 7 – Separate-Type Detector Dimensional Specifications
- Page 8 – TIC-LF654L Flowmeter Dimensional Data
- Page 9 – Flowmeter External Connections and Wiring
- Page 10 – Separate-Type Flowmeter Wiring Terminal Specifications
- Page 11 – Electromagnetic Flowmeter Wiring Guidelines
- Page 12 – TIC-LF654L Installation and Ordering Information
- Page 13 – Flange-Type Detector Specification Codes
- Page 14 – TIC-LF654L Converter Communication Specifications
TIC-LF654L
Introduction
The electromagnetic flowmeter uses Faraday’s Law of
electromagnetic induction to measure the process flow.
The device consists of two units: a detector, through
which the fluid to be measured flows and in which
low-level signals proportional to flow rates are
obtained; and a converter, which supplies excitation
current to the detector, and amplifies the signals from
the detector and then processes and converts the signals
into the 4–20 mAdc current signal or communication
signal. The meter features a
Mount-Anywhere
magnetic field distribution technology, the meter is
highly immune to upstream flow disturbances.
Combined with a multi-functional converter LF620
(combined type) or LF622 (separate type) equipped
with its patented
Noise-Sentry
original noise-
suppression circuit and advanced algorithms. The
LF654 has a very high tolerance to noise, giving the unit
a very stable output even for slurry fluid measurement.
IR (Infrared) switches enable parameter setting of the
converter without removing the cover. Flow direction
can be set in either way, and its unique 128 x 128 dot
matrix LCD display allows the LCD to be rotated
electronically to 90, 180 and 270 degrees without
opening the cover.
* HART protocol (Highway Addressable Remote Transducer) is
a communication protocol for industrial sensors recommended
by the HCF (HART Communication Foundation).
** DevComm2000 Smart Device Communicator available
through TIC for performing HART device configurations on
PC or laptop .
* PROFIBUS is the communications protocol for factory and
process automation that the PROFIBUS Organization
recommends. Instead of analog control with a conventional
analog signal (4-20 mA), it is fieldbus which digitizes all
signals. Flowmeters support PROFIBUS-PA.
* Modbus is the communication protocol that Modicon Inc.
developed. Physical layer is RS485.
C om b ine d t yp e
Se par at e t yp e
Figure1. Configuration
LF654/LF620F LF654 LF622F
Figure2. LF654 Mount-Anywhere Series
Flowmeters
Specifications
Overall Specifications
Measurement range in terms of flow velocity:
0 –1.0 ft/s to 0 – 39.4ft/s (0 – 0.3 m/s to 0 –12 m/s).
0 – 0.3 ft/s to 0 – 1.0 ft/s (0 – 0.1 m/s to 0 – 0.3 m/s)
range is available optionally.
Accuracy:
< 1/2" to 18" ( 15mm to 450mm) >
±0.2 % of Rate
*
* This pulse output error result is established under standard
operating conditions at Toshiba admitted flow calibration
facility. (NIST Traceable)
* Individual meter measurement error may vary up to ±0.5% of
Rate at 1.64 ft/s (0.5m/s) or more and ±0.3% of rate ±0.039
inch/s (1mm/s) at 1.64 ft/s or less.
* Current output: plus ± 8µA (0.05% of span.)
* Refer to individual calibration data for each individual meter's
measurement error.
Field Intelligent Device – Mount Anywhere Series - Flanged
Electromagnetic Flowmeter
LF654 /LF620
LF654 /LF622
1/2" to 18" (15 to 450 mm)
Certification
No. Z01207
For PU and
HR lined flowmeter
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Was this manual helpful?
About this manual
- Brand
- Toshiba
- Model
- LF654
- Document type
- Manual
- Language(s)
- English
- Pages
- 14
- File size
- 334.7 KB
- Format
Summary
Details on the operation based on Faraday’s Law, Mount-Anywhere design for immune flow measurement, communication protocols, and product specifications including measurement range and accuracy.
Technical requirements for the LF654 Detector, covering fluid conductivity, temperature ranges, mounting style, pressure limits, connection flange standards, materials, and hazardous location certifications.
Input/output signal specifications for LF620 and LF622 converters, including analog and digital inputs, totalizer control, zero adjustment, and communication protocols like HART, PROFIBUS, and MODBUS parameters.
