Toshiba B-8204-QM-R - Manual
Toshiba B-8204-QM-R – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 4 – Free
- Page 7 – Installing the Rotary Cutter Unit on the B-SX5T Series; Remove the two black screws to detach the front plate.; Front Plate
- Page 9 – Operation Panel Ass’y
- Page 15 – 万一、不足しているものがある場合は、お買い上げの販売店までご連絡ください。; カッターモジュール; ●本書の手順に従って組み込むこと; 注意事項
- Page 16 – ■組込手順; 補足; 目隠し板および化粧ネジは、紛失しないよう大切に保管してください。
- Page 17 – ) 印字ヘッド機構部を持ち上げてロックします。
- Page 19 – Main PC
- Page 20 – ケーブル類をかまないように、カッター機構部を固定してください。; 7) カッターカバーを取り付け、カバーに付いている2本の化粧ネジで固定します。; ・カッターカバーを取り付けたとき、カバー内側の突起部がカッターカバースイッチを ON にしていることを確認してくだ
- Page 21 – ケーブル類をかまないように、左サイドカバーを確実に取り付けてください。
- Page 22 – Printed in Japan; C東芝テック株式会社
- 1 -
Rotary Cutter Module
B-8204-QM-R Installation Manual
1. APPLICABLE MODEL
This optional kit is the rotary cutter module, which is intended for the following models:
B-SX4T Series, B-SX5T Series
NOTE:
When using the Rotary Cutter to the B-SX4T Series, be sure to install the Ribbon Saving Module
(B-9904-R/R2-QM). Failure to do this may cause a paper jam or ribbon error.
2. PACKING LIST
All the following parts are supplied with the kit. Make sure you have all items shown below.
Cutter Unit (1 pc.)
Cutter Cover (1 pc.)
Cutter Drive Unit (1 pc.)
Harness Ass’y
(2-pin & 9-pin) (1 pc.)
Cord Bush (1 pc.)
(For B-SX4 only)
Print Head Cleaner (1 pc.)
(P/No.: FMQB0051601)
•
Installation Manual (1 copy)
•
SM-4x8 Screw (6 pcs.)
3. INSTALLATION PROCEDURE
3.1 Installing the Rotary Cutter Unit on the B-SX4T Series
1) Turn the power off and disconnect the power cord.
2)
Remove the two black screws to detach the front plate.
NOTE:
Retain the two black screws and front plate.
WARNING!
1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or
electrocution.
•
Manual instructions must be followed when installing option kits or adding cables to avoid
system failures and to insure proper performance and operation
•
Failure to follow manual instructions or any unauthorized modifications, substitution or change
to this product will void the limited product warranty.
2. Turn the power off and disconnect the power cord before installing the rotary cutter module.
3. Be careful not to injure your fingers when installing the swing cutter module.
4. Be careful not to pinch your fingers or hands with the covers.
Front Plate
Black Screws
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
- 4 - 11) Fix the harness ass’y with the clamp. 12) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the Main PC board, respectively. 13) Turn the head lever counterclockwise to Free position. 14) Open the ribbon shaft holder plate. 15) Raise the print head bl...
- 7 - 3.2 Installing the Rotary Cutter Unit on the B-SX5T Series Since the strip module is standard on the B-SX5T series, it is necessary to remove the rewinder guide plate, strip sensor, etc. before installing the cutter module. 1) Turn the power off and disconnect the power cord. 2) When the print...
- 9 - 10) Disconnect the operation panel harness from the operation panel ass’y. 11) Turn the head lever clockwise to Free position. 12) Open the ribbon shaft holder plate. Operation Panel Ass’y Ribbon Shaft Holder Plate Operation Panel Harness Hook Head Lever Free position Lock position(Label) Lock...
