TANDBERG RJ45RJ11 - Manual
TANDBERG RJ45RJ11 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Installation of the Video Switch
- Page 4 – Important; Communicating with the Video Switch
- Page 5 – Configuration Commands; Switch control commands; Set; Inquiries
- Page 6 – 㑻ໄᯢ; Position of the Declaration
116467.05
Page 1 of 6
3
1
Unpack the unit.
2
Mount the rack ears
and/or rubber feet
and mount it in the
rack, if applicable.
Connecting the Video Switch
Put the Video Switch power
supply here when rack
mounting.
Rubber feet
(rubber pads)
Audio out
Data
Net
PC Card
1. Single
2. Single
Video out
Video in
3. Dual
2. Aux
3. Doc
4. VCR
VCR
Ethernet
PC DVI-I in
DVI-I out
1
2
4
Audio in
1
Mic.1
2
Mic.2
3
USB
USB
DC in
I
O
Camera
Connect TANDBERG Video Switch
power supply here.
Connect camera power supply
here.
TANDBERG Video Switch
TANDBERG 6000
MXP
Codec
TANDBERG 3000
MXP
Codec
Connecting up to four
TANDBERG Precision
HD cameras:
RJ1
1
–
RJ45
RJ1
1
–
RJ45
RJ1
1
–
RJ45
DVI – HDMI
DB 9 – RJ 45
RJ 45 – DB 9
DB
9–RJ
45
DVI – HDMI
DVI – HDMI
Camera 2
Camera 3
Camera 4
The Video Switch set contains:
1 Video Switch Unit
4 Rubber Feet
1 HD Camera cable (1 m) for 6000MXP Codec
1 HD Camera cable (1 m) for 3000MXP Codec
1 Power supply kit incl. cables for Video Switch
1 Power supply kit incl. cables for existing camera
1 Rack ear set (left and right)
1 Control cable (6.5 m) for Video Switch to Precision HD camera
1 HDMI cable (6.5 m) for Video Switch to precision HD camera
1 TRC4 TANDBERG Remote Control
Please report any discrepancies immediately.
Primary chain
The Codec must be equipped with
software version F6.1 or higher to
support the use of the Video Switch.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
116467.05 Page 3 of 6 Basic Functionality Physical inputs refer to explicit codec input and explicit switch input. These can only be controlled from the command interface. xconfiguration MainVideoSource, vidin and xconfiguration Switch Source always control the inputs directly. Example: To select ph...
116467.05 Page 4 of 6 VISCA Standard Commands Command Set Command Packet Comments CAM_IF_Clear 8x 01 00 01 ff Clear command buffer. Stop any current operation in progress. CAM_ Address_Set 8x 30 0p ff p = address for this device. If x=8 (broadcast), increase p with 1 before sending to chain. CAM_Com...
116467.05 Page 5 of 6 Configuration Commands Messages starting with 8x-01-40-<00..1f> are configuration commands. Command Command Packet Comments SW_Port_0_Cfg 8x 01 40 00 ... ff Currently not in use. SW_Port_1_Cfg 8x 01 40 01 ... ff Currently not in use. SW_Port_2_Cfg 8x 01 40 02 0p ff p=0: D...
