Sunrise Medical Ti Titanium - Manual

Page 2 - I . I n t r o d u c t i o n; SUNRISE LISTENS; Customer Service Department; FOR ANSWERS TO YOUR QUESTIONS

930487 Rev. A I . I n t r o d u c t i o n 3 SUNRISE LISTENS Thank you for choosing a Quickie wheelchair. We want to hear your questions or com-ments about this manual, the safety and reliability of your chair, and the service youreceive from your supplier. Please feel free to write or call us at the...

Page 3 - XII. SUNRISE LIMITED WARRANTY; I I . T a b l e o f C o n t e n t s; II. TABLE OF CONTENTS

930487 Rev. A I I . T a b l e o f C o n t e n t s 5 VIII. WARNINGS: COMPONENTS & OPTIONS ..................................................... 22 A. Anti-Tip Tubes................................................................................... 22B. Armrests ......................................

Page 4 - Bead finished Titanium; I I I . Y o u r C h a i r & I t s P a r t s

930487 Rev. A I I I . Y o u r C h a i r & I t s P a r t s 7 Weight 16.9 lbs. (16 x 16 spoke wheels) (Chair weight will vary per component options) Adjustments Caster, CG, rear seat height, backangle, footrest length Color Bead finished Titanium Frame Dimensions Frame width: Std 13"-18"Se...

Page 6 - J. MOTOR VEHICLE SAFETY; V . G e n e r a l W a r n i n g s; NOTE–

930487 Rev. A V . G e n e r a l W a r n i n g s 11 H. TERRAIN 1. Your chair is designed for use on firm, even surfaces such as concrete, asphalt and indoor floors and carpeting. 2. Do not operate your chair in sand, loose soil or over rough terrain. This may damage wheels or axles, or loosen fastene...

Page 7 - B. DRESSING OR CHANGING CLOTHES; K. WHEN YOU NEED HELP

930487 Rev. A V I . W a r n i n g s : F a l l s & T i p - O v e r s 13 A. CENTER OF BALANCE The point where this chair will tip forward, back, or to the side depends on its centerof balance and stability. How your chair is set up, the options you select and thechanges you make may affect the ris...

Page 10 - V I I . W a r n i n g s : F o r S a f e U s e; A. LEARNING TO DO A “WHEELIE”; Follow these steps to help the rider learn to do a “wheelie”:; B. DESCENDING A CURB OR SINGLE STEP; around and pull it backward.

930487 Rev. A V I I . W a r n i n g s : F o r S a f e U s e 19 Before you assist a rider, be sure to read the warnings “For Attendants” (p. 12) andfollow all instructions that apply. Be aware that you will need to learn safe methodsbest suited to your abilities. A. LEARNING TO DO A “WHEELIE” Follow ...

Page 11 - C. CLIMBING A CURB OR SINGLE STEP

930487 Rev. A V I I . W a r n i n g s : F o r S a f e U s e 21 E. DESCENDING STAIRS 1. Use at least two attendants to move a chair and rider down stairs.2. Move the chair and rider FORWARD down the stairs.3. The person at the rear is in control. He or she tilts the chair to the balance point of the ...

Page 14 - release tension on ball bearings at other end.; V I I I . W a r n i n g s : C o m p o n e n t s & O p t i o n s; M. MODIFIED SEAT SYSTEMS; stretching of fabrics at rivet holes.; Button

930487 Rev. A I X . S e t - U p & A d j u s t m e n t 27 A. TO MOUNT & REMOVE REAR WHEELS (OPTIONAL) Do not use this chair UNLESS you are sure bothquick-release axles are locked. An unlockedaxle may come off during use and cause a fall. NOTE– The axle is not locked until the quick-releasebut...

Page 15 - A torque setting is the

930487 Rev. A I X . S e t - U p & A d j u s t m e n t 29 I X . S e t - U p & A d j u s t m e n t 930487 Rev. A 28 F. ADJUSTING REAR SEAT HEIGHT Prior to adjusting rear seat height, follow the instruc-tions in Section H-4. To adjust rear seat height, loosenand remove the 8 cap screws (A) (4 p...

Page 16 - able

930487 Rev. A I X . S e t - U p & A d j u s t m e n t 31 Once the axle and back plates are secured, attach therear wheels, occupy the chair and maneuver it with aspotter to get a feel for the new adjustment. 2. Wheel Camber The wheel camber adjustment provides greater side-to-side stability due ...

Page 17 - Adjusting Caster Angle

930487 Rev. A I X . S e t - U p & A d j u s t m e n t 33 I X . S e t - U p & A d j u s t m e n t 930487 Rev. A 32 I. CASTERS NOTE– Setting the wheelchair on a flat surface table ora workbench helps make these procedures easier. NOTE ON TORQUE SETTING– A torque setting is the optimum tighteni...

Page 19 - X . T r o u b l e s h o o t i n g; To keep track of your progress, make only ONE change at a time.; SOLUTIONS

930487 Rev. A X . T r o u b l e s h o o t i n g 37 I X . S e t - U p & A d j u s t m e n t 930487 Rev. A 36 You will need to adjust your chair from time to time for best performance (especially ifyou alter the original settings). This chart gives you a first solution, then a second and athird if...

Page 20 - Axles and Moving Parts

930487 Rev. A X I . M a i n t e n a n c e 39 X I . M a i n t e n a n c e 930487 Rev. A 38 C. MAINTENANCE TIPS 1. Axles & Axle Sleeves Check axles and axle sleeves every six months to make sure they are tight. Loosesleeves will damage the camber tube and will affect performance. 2. Tire Air Press...

Page 21 - The expected life of this frame is five years.; F. NOTICE TO CONSUMER; vary from state to state.

930487 Rev. A N o t e s 41 X I I . S u n r i s e L i m i t e d W a r r a n t y 930487 Rev. A 40 A. FOR LIFETIME Sunrise warrants the frame and quick-release axles of this wheelchair against defectsin materials and workmanship for the life of the original purchaser. The expected life of this frame is...

Page 23 - Sunrise Medical; 477 East Dry Creek Parkway

©2002, Sunrise Medical 8.02 930487 Rev. A Sunrise Medical 7477 East Dry Creek Parkway Longmont, Colorado 80503 USA 303-218-4600 (800) 333-4000 In Canada (800) 263-3390 This product is manufacturedto comply with the ‘MedicalDevice Directive’ 93/42/EEC.

Sunrise Medical Ti Titanium - Manual

Table of Contents:

Summary

Other Sunrise Medical Models