Summit Appliance BIM271OS - User Manual

Page 2 - IMPORTANT SAFETY INSTRUCTIONS; qualified electrician replace the power cord.

IMPORTANT SAFETY INSTRUCTIONS DANGER – Risk of fire or explosion. FLAMMABLE REFRIGERANT USED. Do not use mechanical devices to defrost the refrigerator. Do not puncture refrigerant tubing. DANGER – Risk of fire or explosion. FLAMMABLE REFRIGERANT USED. To be repaired only by trained service personne...

Page 3 - bed and breakfast type environments; THE MANUFACTURER DISCLAIMS ANY RESPONSIBILITY IF THE ABOVE

OTHER PRECAUTIONS • To ensure proper ventilation for the appliance, keep obstructions away from the front of the unit. • Keep fingers out of the “pinch point” areas. Clearance between the door and cabinet are small. Be careful closing the door when children are in the area. • Do not touch the evapor...

Page 4 - TABLE OF CONTENTS; Installation

TABLE OF CONTENTS Product Overview and Specs ........................................................................... 1 - 2 Installation Before Using Your Ice Maker ...................................................................................................... 3 Installing the Ice Maker .....

Page 5 - Product Overview and Specs; Model; Yes; and shall not be exposed directly to rain.

1 Product Overview and Specs Model BIM26H32 / BIM26H34 / BIM27OSADA / BIM271OS Voltage/Frequency AC 115V 60Hz Rated Ice making current 1.9A Rated Ice harvest current 1.5A Refrigerant R600a, 1.58Oz. Indoor/Outdoor Indoor/Outdoor* IP Rating IPX4 ADA Yes Installation Type Free standing / Built-in Worki...

Page 6 - Front View; Ice Module

2 Front View Ice Module Ice Bucket Power Switch Front Vents

Page 7 - Rear View; Power

Page 8 - BEFORE USING YOUR ICE MAKER; Clean the interior surface with lukewarm water using a soft cloth.

Accessories Handle Ice Scoop Ice Bucket Left Latch Block & Hook In Line Filter Clips High Feet × 4 Lower Grill INSTALLATION BEFORE USING YOUR ICE MAKER • REMOVE THE EXTERIOR AND INTERIOR PACKAGING MATERIAL. • CHECK TO BE SURE YOU HAVE ALL OF THE FOLLOWING PARTS: • 1 DOOR HANDLE • 1 ICE BUCKET • ...

Page 9 - INSTALLING THE ICE MAKER; This appliance is designed to expel hot air through the front vent.

4 INSTALLING THE ICE MAKER CAUTIONS: • The appliance shall not be exposed to rain even for the model with ipx4. • This appliance is designed to expel hot air through the front vent. This allows for installation in a recessed or built-in application, if desired. • Place your ice maker on a level surf...

Page 10 - INSTALLING THE HANDLE; Phillips screwdriver

5 INSTALLING THE HANDLE This appliance comes with a stainless steel handle. To install the handle please follow the below instructions: Tools needed: Phillips screwdriver 1. Peel away the gasket from behind the door. There are two mounting holes covered by caps. Remove those caps and insert the scre...

Page 11 - REVERSING THE DOOR SWING; flathead screwdriver, Phillips screwdriver; REMOVING THE DOOR; that are in the in the opposite hinge.; REINSTALLING THE DOOR; on the opposite side.

6 REVERSING THE DOOR SWING NOTE: Some models may not be reversible in the field This appliance can have the door open from either the left or right side. The unit is delivered with the door opening from the left side (hinged on the right). Tools needed: flathead screwdriver, Phillips screwdriver IMP...

Page 12 - Filter Installation Instructions

Filter Installation Instructions Tools needed: Phillips screwdriver 1. Connecting the filter to the potable water supply Remove the blue clip to remove the filter’s plug, then connect the filter to portable water supply by inserting the water supply tube to the inlet end of the filter. Reinsert the ...

Page 13 - Built-in Installation; to the cabinet when installing the unit.

8 Built-in Installation This product is designed to seamlessly integrate into a space that must follow the specifications in the table below which require precise measurement. The opening must be square and plumb front to back. Although not required, you can increase the overall width of the cutout ...

Page 14 - Raising the Height of the Unit; height can be adjusted to 33 1⁄2” and up to 34 1⁄2”.; Changing the Feet; and replace it with the high feet.; Lower Grill Change

9 Raising the Height of the Unit This ice maker is ADA compliant, but by switching to the alternate feet provided, the default height can be adjusted to 33 ½” and up to 34 ½”. Tools needed: Phillips screwdriver Changing the Feet Using two or more people, lean the ice maker onto its back and unscrew ...

Page 16 - OPERATING THE ICE MAKER; off, remove cubes and keep door open at least two inches.; MAINTENANCE; CLEANING YOUR ICE MAKER

OPERATING THE ICE MAKER INITIAL SET-UP 1. Plug the appliance into a 115/120v polarized and grounded wall electrical outlet. 2. Place the on-off switch in the “I” position. 3. Make sure the water supply is on. As soon as the inner mechanism reaches the proper temperature, the icemaker mechanism will ...

Page 18 - TROUBLESHOOTING GUIDE; Problem

13 TROUBLESHOOTING GUIDE Before Calling for Service: If the unit is malfunctioning, read through the troubleshooting guide below. Some of the problems mentioned in the Troubleshooting Guide can be solved easily without a service call. Problem Possible Cause Possible Solution The ice maker does not o...

Page 20 - LIMITED WARRANTY; ONE-YEAR LIMITED WARRANTY; ITEMS WARRANTOR WILL NOT PAY FOR:; DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES

15 For parts and accessory ordering, troubleshooting and helpful hints, visit: www.summitappliance.com/support LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instru...

Summit Appliance BIM271OS - User Manual

Table of Contents:

Summary

Other Summit Appliance Ice Makers Models