Page 5 - STAR Command Specifications; GENERAL DESCRIPTION; • Dot impact printers
1-1 STAR Command Specifications Rev. 0.70 1. GENERAL DESCRIPTION This specifications document describes the command specifications for the STAR MODE on dot impact printers. Information contained herein applies to models with the following conditions. • Dot impact printers • Printer head: 72 DPI (ver...
Page 6 - COMMAND FUNCTION LIST; Class
2-1 STAR Command Specifications Rev. 0.70 2. COMMAND FUNCTION LIST • Standard Commands Class Commands Name Font Style and Character Set ESC GS t Specify code page ESC R Specify international character set ESC / Specify/cancel slash zero ESC 6 Switch to IBM character set #2 (only with standard specif...
Page 9 - -1 Explanation of Terms; This is an abbreviation of Most Significant Bit.
3-1 STAR Command Specifications Rev. 0.70 3. COMMAND DETAILS 3-1 Explanation of Terms • Reception bufferThe buffer for storing data (reception data) received from the host, as it is called the reception buffer.Reception data is temporarily stored in the reception buffer, then processed sequentially....
Page 10 - -2 Exception processing
3-2 STAR Command Specifications Rev. 0.70 3-2 Exception processing 1) Undefined codesCodes from <00>H to <1F>H are targeted.When codes not defined as commands in this region are received, they are discarded. (Ex.) If processing the data string of <30>H<31>H<03>H<32&g...
Page 11 - -3 Standard Command Details
3-3 STAR Command Specifications Rev. 0.70 3-3 Standard Command Details 3-3-1 Font style and character set ESC GS t n [Name] Select code page[Code] ASCII ESC GS t n Hexadecimal 1B 1D 74 n Decimal 27 29 116 n [Defined Area] n differs depending on the specifications. (See the table below.) [Initial Val...
Page 12 - ESC R n
3-4 STAR Command Specifications Rev. 0.70 ESC R n [Name] Specify international character set [Code] ASCII ESC R n Hexadecimal 1B 52 n Decimal 27 82 n [Defined Area] 0 ≤ n ≤ 14 n = 64 [Initial Value] Memory switch setting [Function] Specifies international characters according to the value of n. n In...
Page 14 - ESC M
3-6 STAR Command Specifications Rev. 0.70 ESC M [Name] Specify 7 x 9 font (half dots) (default) [Code] ASCII ESC M Hexadecimal 1B 4D Decimal 27 77 [Defined Area] --- [Initial Value] --- [Function] Specifies 7 x 9 (half) dot font. Sets the number of printable digits in one line to [total half dot cou...
Page 15 - ESC SP n
3-7 STAR Command Specifications Rev. 0.70 ESC : [Name] Specify 5 x 9 font (3P-1) [Code] ASCII ESC : Hexadecimal 1B 3A Decimal 27 58 [Defined Area] --- [Initial Value] --- [Function] Specifies 5 x 9 (3 pulse = 1) dot fonts. Sets the number of printable digits in one line to [total half dot count/(18 ...
Page 16 - SO
3-8 STAR Command Specifications Rev. 0.70 3-3-2 Character Expansion Settings SO [Name] Specify double-wide expanded characters [Code] ASCII SO Hexadecimal 0E Decimal 14 [Defined Area] --- [Initial Value] Cancel double-wide expanded characters [Function] Prints ANK characters and Kanji characters wit...
Page 17 - ESC W n
3-9 STAR Command Specifications Rev. 0.70 ESC W n [Name] Specify/cancel expanded double-wide printing [Code] ASCII ESC W n Hexadecimal 1B 57 n Decimal 27 87 n [Defined Area] n = 0, 1, 48, 49 [Initial Value] n = 0 (Horizontal double-wide printing cancelled) [Function] Specifies/cancels horizontal dou...
Page 18 - ESC E; ESC F
3-10 STAR Command Specifications Rev. 0.70 3-3-3 Print mode ESC E [Name] Select emphasized printing [Code] ASCII ESC E Hexadecimal 1B 45 Decimal 27 69 [Defined Area] --- [Initial Value] Emphasized printing cancelled. [Function] Specifies emphasized printing for subsequent data. When in emphasized pr...
Page 19 - ESC – n; Underlines are applied to the 9; ESC n; Upperlines are applied to the 1st dot of the character.
3-11 STAR Command Specifications Rev. 0.70 ESC – n [Name] Specify/cancel underling mode [Code] ASCII ESC - n Hexadecimal 1B 2D n Decimal 27 45 n [Defined Area] n = 0, 1, 48, 49 [Initial Value] n = 0 (Underline cancelled) [Function] Specifies underline according to the value of n. n Function 0, 48 Ca...
Page 21 - ESC GS 4 m n; white line to appear between characters.)
3-13 STAR Command Specifications Rev. 0.70 ESC GS 4 m n [Name] Select red/black substitute function [ESC 4/5 setting] [Code] ASCII ESC GS 4 m n Hexadecimal 1B 1D 34 m n Decimal 27 29 52 m n [Defined Area] m = 1, 2, 49, 50 When m = 1, 49 n = 0 to 3, 255 When m = 2, 50 n = 0, 2 to 5 When m = 83 n = 0,...
Page 22 - character, 7FHex is a target for this setting.
3-14 STAR Command Specifications Rev. 0.70 When m = 83 (“S”) Red/black adornment of ANK space characters (20H). m n Red adornment of ANK space characters (20H). 83 0 Adorn 83 1 Do not adorn This parameter specifies whether to adorn red/black for ANK space characters in red printing mode (black/white...
Page 24 - ESC RS i n
3-16 STAR Command Specifications Rev. 0.70 ESC RS i n [Name] Specify/cancel character rotated mode [Code] ASCII ESC RS i n Hexadecimal 1B 1E 69 n Decimal 27 30 105 n [Defined Area] 0 ≤ n ≤ 2 48 ≤ n ≤ 50 (“0” ≤ n ≤ “2”) [Initial Value] Character rotation cancelled (n = 0) [Function] Specifies directi...
Page 25 - LF
3-17 STAR Command Specifications Rev. 0.70 3-3-4 Line Spacing LF [Name] Line feed[Code] ASCII LF Hexadecimal 0A Decimal 10 [Defined Area] --- [Initial Value] Set line feed to 1/6 inch [Function] After printing data in the line buffer, paper is fed according to the currently set line feed amount. CR ...
Page 26 - ESC a n
3-18 STAR Command Specifications Rev. 0.70 ESC a n [Name] Feed paper n lines [Code] ASCII ESC a n Hexadecimal 1B 61 n Decimal 27 97 n [Defined Area] 1 ≤ n ≤ 127 [Initial Value] --- [Function] After printing data in the line buffer, paper is fed according to (currently set line feed amount x n). This...
Page 27 - ESC z 0; ESC z 1
3-19 STAR Command Specifications Rev. 0.70 ESC z 0 [Name] Set line feed to 1/12 inch[Code] ASCII ESC z 0 Or ESC z “0” Hexadecimal 1B 7A 00 1B 7A 30 Decimal 27 122 0 27 122 48 [Defined Area] --- [Initial Value] 1/6 inch [Function] Sets subsequent line feed amounts to 1/12 inch. ESC z 1 [Name] Set lin...
Page 28 - ESC A n
3-20 STAR Command Specifications Rev. 0.70 ESC A n [Name] Define n/72 inch pitch line feed [Code] ASCII ESC A n Hexadecimal 1B 41 n Decimal 27 65 n [Defined Area] 0 ≤ n ≤ 85 [Initial Value] n = 12 (1/6 inch line feed) [Function] Defines line feed amount for one line as n/72 inch. To enable this code...
Page 29 - ESC 3 n
3-21 STAR Command Specifications Rev. 0.70 ESC 3 n [Name] Set line feed to n/216 inch line feed pitch (approximate value) [Code] ASCII ESC 3 n Hexadecimal 1B 33 n Decimal 27 51 n [Defined Area] 0 ≤ n ≤ 255 [Initial Value] n = 36 (1/6 inch) [Function] Sets subsequent line feed amounts to a value appr...
Page 30 - ESC J n
3-22 STAR Command Specifications Rev. 0.70 ESC J n [Name] Execute n/72 inch paper feed one time[Code] ASCII ESC J n Hexadecimal 1B 4A n Decimal 27 74 n [Defined Area] 1 ≤ n ≤ 255 [Initial Value] --- [Function] After printing data in the line buffer, paper is fed n/72 of an inch in the forward paper ...
Page 31 - FF; Executes a 1 inch paper feed.
3-23 STAR Command Specifications Rev. 0.70 3-3-5 Page Control Commands FF [Name] Form feed[Code] ASCII FF Hexadecimal 0C Decimal 12 [Defined Area] --- [Initial Value] --- [Function] This command performs the following operations after the printer prints the printing data in the line buffer. Operatio...
Page 32 - ESC C n; ESC C NUL n
3-24 STAR Command Specifications Rev. 0.70 ESC C n [Name] Set page length to n lines [Code] ASCII ESC C n Hexadecimal 1B 43 n Decimal 27 67 n [Defined Area] 1 ≤ n ≤ 255 [Initial Value] 1/6 inch x 42 [Function] This command sets the length of one page to [currently set line feed amount x n] lines The...
Page 33 - VT; ESC B n1 n2 ... nk NUL
3-25 STAR Command Specifications Rev. 0.70 VT [Name] Feed paper to vertical tab position [Code] ASCII VT Hexadecimal 0BDecimal 11 [Defined Area] --- [Initial Value] --- [Function] This command performs paper feeds up to the next vertical tab position after the printer prints the data in the line buf...
Page 34 - ESC N n; ESC O; Page Length
3-26 STAR Command Specifications Rev. 0.70 ESC N n [Name] Set bottom margin to n lines [Code] ASCII ESC N n Hexadecimal 1B 4E n Decimal 27 78 n [Defined Area] 0 ≤ n ≤ 255 (Not full page length) [Initial Value] n = 0 [Function] This command sets the bottom margin position to (current line feed amount...
Page 35 - -3-6 Horizontal Direction Printing Position; Print Region
3-27 STAR Command Specifications Rev. 0.70 3-3-6 Horizontal Direction Printing Position ESC RS A n [Name] Set print region [Code] ASCII ESC RS A n Hexadecimal 1B 1E 41 n Decimal 27 30 65 n [Defined Area] Specification 1 0 ≤ n ≤ 3 Specification 2 0 ≤ n ≤ 5 [Initial Value] MSW Setting [Function] After...
Page 36 - ESC l n; Printable Region
3-28 STAR Command Specifications Rev. 0.70 ESC l n [Name] Set left margin [Code] ASCII ESC l n Hexadecimal 1B 6C n Decimal 27 108 n [Defined Area] 0 ≤ n ≤ (right margin -2) ≤ 255 [Initial Setting] n = 0 [Function] This command sets the left margin (current ANK character pitch x n) using the left edg...
Page 37 - ESC Q n
3-29 STAR Command Specifications Rev. 0.70 ESC Q n [Name] Set right margin[Code] ASCII ESC Q n Hexadecimal 1B 51 n Decimal 27 81 n [Defined Area] 2 ≤ n ≤ maximum printable digits ≤ 255 [Initial Value] Maximum printable digits [Function] This command sets the printable region (current ANK character p...
Page 38 - HT
3-30 STAR Command Specifications Rev. 0.70 HT [Name] Move horizontal tab [Code] ASCII HT Hexadecimal 09 Decimal 9 [Defined Area] --- [Initial Value] --- [Function] Move print position to next horizontal tab position. The current position moves to the next tab position when at the horizontal tab posi...
Page 39 - ESC GS a n
3-31 STAR Command Specifications Rev. 0.70 ESC GS a n [Name] Specify position alignment[Code] ASCII ESC GS a n Hexadecimal 1B 1D 61 n Decimal 27 29 97 n [Defined Area] 0 ≤ n ≤ 2 48 ≤ n ≤ 50 (“0” ≤ n ≤ “2”) [Initial Value] n = 0 [Function] This specifies position alignment for all data in one line, i...
Page 40 - ESC GS A n1 n2; ESC GS R n1 n2
3-32 STAR Command Specifications Rev. 0.70 ESC GS A n1 n2 [Name] Specify absolute position [Code] ASCII ESC GS A n1 n2 Hexadecimal 1B 1D 41 n1 n2 Decimal 27 29 65 n1 n2 [Defined Area] 0 ≤ n1 ≤ 255 0 ≤ n2 ≤ 255 [Initial Value] --- [Function] Moves the printing position to the (n1 + n2 x 256) position...
Page 41 - Relationship of character pattern data and print head.; x 9 font characters are always printed.
3-33 STAR Command Specifications Rev. 0.70 3-3-7 Download ESC & NUL n1 n2 [m d1 d2 d3 d4 d5 (d6 d7)] n2 - n1 + 1 [Name] Register download characters (vertical 1 byte font) [Code] ASCII ESC & NUL n1 n2 [m d1 d2 d3 d4 d5 (d6 d7)] n2 - n1 + 1 Hexadecimal 1B 26 00 n1 n2 [m d1 d2 d3 d4 d5 (d6 d7)...
Page 45 - MSB
3-37 STAR Command Specifications Rev. 0.70 Relationship of character pattern data and print head. [Ex.] When selecting 7 x 9 fonts, and defining the character to 21H: ESC & m c1 c2 d1 d2 d3 d4 d5 d6 d7 d8 d9 d10 d11 d12 d13 d14 Code (Hexadecimal) 1B 26 02 21 21 1F 00 20 00 44 00 00 00 44 00 20 0...
Page 48 - ESC K n NUL d1 d2 ... dn; Pin Used
3-40 STAR Command Specifications Rev. 0.70 3-3-8 Bit Image Graphics ESC K n NUL d1 d2 … dn [Name] Standard density bit image [Code] ASCII ESC K n NUL d1 d2 .. dn Hexadecimal 1B 4B n 00 d1 d2 .. dn Decimal 27 75 n 0 d1 d2 .. dn [Defined Area] 1 ≤n ≤total dot count 0 ≤ d ≤ 255 [Initial Value] --- [F...
Page 50 - • When m is outside the defined area, the following process occurs.
3-42 STAR Command Specifications Rev. 0.70 ESC �� m n1 n2 d1 d2 … dk �� m n1 n2 d1 d2 … dk m n1 n2 d1 d2 … dk [Name] 9/16/18 bit image graphics [Code] ASCII ESC ^ m n1 n2 d1 d2 .. dk Hexadecimal 1B 5E m n1 n2 d1 d2 .. dk Decimal 27 94 m n1 n2 d1 d2 .. dk [Defined Area] Spec. 1 0 ≤ m ≤ 1 (“0” ≤ m ≤ “...
Page 55 - ESC FS p n m
3-47 STAR Command Specifications Rev. 0.70 ESC FS p n m [Name] Print logo[Code] ASCII ESC FS p n m Hexadecimal 1B 1C 70 n m Decimal 27 28 112 n m [Defined Area] 1 ≤ n ≤ 255 (When printing normally) 0 ≤ m ≤ 3 48 ≤ m ≤ 51 (“0” ≤ m ≤ “3”) [Initial Value] --- [Function] Prints the logo of the number n r...
Page 56 - ESC d n
3-48 STAR Command Specifications Rev. 0.70 3-3-11 Cutter Control ESC d n [Name] Paper cut instruction [Code] ASCII ESC d n Hexadecimal 1B 64 n Decimal 27 100 n [Defined Area] 0 ≤ n ≤ 3 48 ≤ n ≤ 51 (“0” ≤ n ≤ “3”) [Initial Value] --- [Function] This command executes the auto-cut according to the n sp...
Page 57 - Prohibit Printing, Paper Feed; Print Operation
3-49 STAR Command Specifications Rev. 0.70 3-3-12 External Device Drive ESC BEL n1 n2 [Name] Set external drive device 1 pulse width [Code] ASCII ESC BEL n1 n2 Hexadecimal 1B 07 n1 n2 Decimal 27 7 n1 n2 [Defined Area] 1 ≤ n1 ≤ 127 1 ≤ n2 ≤ 127 [Initial Value] n1 = 20 (Energizing time: 200 msec) n2 =...
Page 58 - BEL
3-50 STAR Command Specifications Rev. 0.70 BEL [Name] External device 1 drive instruction [Code] ASCII BEL Hexadecimal 07 Decimal 7 [Defined Area] --- [Initial Value] --- [Function] Executes the external device drive conditions set according to the ESC BEL (external device drive pulse width setting ...
Page 59 - SUB
3-51 STAR Command Specifications Rev. 0.70 SUB [Name] External device 2 drive instruction (real time) [Code] ASCII SUB Hexadecimal 1A Decimal 26 [Defined Area] --- [Initial Value] --- [Function] Drives external device 2.The energizing time and delay time are fixed at 200 ms each. The printer execute...
Page 60 - ESC GS EM DC1 m n1 n2
3-52 STAR Command Specifications Rev. 0.70 ESC GS EM DC1 m n1 n2 [Name] Set external buzzer drive pulse condition [Code] ASCII ESC GS EM DC1 m n1 n2 Hexadecimal 1B 1D 19 11 m n1 n2 Decimal 27 29 25 17 m n1 n2 [Defined Area] 1 ≤ m ≤ 2 49 ≤ m ≤ 50 0 ≤ n1 ≤ 255 0 ≤ n2 ≤ 255 [Initial Value] n1 = 0, n2 =...
Page 61 - ESC GS EM DC2 m n1 n2
3-53 STAR Command Specifications Rev. 0.70 ESC GS EM DC2 m n1 n2 [Name] Execute external buzzer drive [Code] ASCII ESC GS EM DC2 m n1 n2 Hexadecimal 1B 1D 19 12 m n1 n2 Decimal 27 29 25 18 m n1 n2 [Defined Area] 1 ≤ m ≤ 2 49 ≤ m ≤ 50 1 ≤ n1 ≤ 20 n2 = 0 [Initial Value] --- [Function] Repeatedly drive...
Page 62 - ENQ; EOT
3-54 STAR Command Specifications Rev. 0.70 3-3-13 Status ENQ [Name] Inquire ENQ status [Code] ASCII ENQ Hexadecimal 05 Decimal 5 [Defined Area] --- [Initial Value] --- [Function] This command is effective only when using an interface capable of bi-directional data communications. When this command i...
Page 63 - ESC ACK SOH; ESC RS a n
3-55 STAR Command Specifications Rev. 0.70 ESC ACK SOH [Name] Inquire status [Code] ASCII ESC ACK SOH Hexadecimal 1B 06 01 Decimal 27 6 1 [Defined Area] --- [Initial Value] --- [Function] This command is effective only when using an interface capable of bi-directional data communications. When this ...
Page 64 - ETB
3-56 STAR Command Specifications Rev. 0.70 ETB [Name] Update ETB status (check after printing) [Code] ASCII ETB Hexadecimal 17 Decimal 23 [Defined Area] --- [Initial Value] Spec. 1 --- Spec. 2 ETB countr = 0 [Function] This command is effective only when using an interface capable of bi-directional ...
Page 65 - ESC RS E n
3-57 STAR Command Specifications Rev. 0.70 ESC RS E n [Name] Initialize ASB ETB counter, and ETB status. [Code] ASCII ESC RS E n Hexadecimal 1B 1E 45 n Decimal 27 30 69 n [Defined Area] n = 0 n = 48 (“0”) [Initial Value] --- [Function] Clears the ASB ETB counter to zero and clears the ETB status of ...
Page 66 - ESC p; ESC q
3-58 STAR Command Specifications Rev. 0.70 3-3-14 Kanji Characters (only on models that carry Kanji characters) ESC p [Name] Specify JIS Japanese character mode (Japanese specifications only) [Code] ASCII ESC p Hexadecimal 1B 70 Decimal 27 112 [Defined Area] --- [Initial Value] Select JIS Japanese c...
Page 70 - Horizontal 16 Dots
3-62 STAR Command Specifications Rev. 0.70 They are designed as shown below and data is sent sequentially. The font of Chinese download characters is composed of 16 x 16 dot patterns. Bits that correspond to the dots to print are “1,” and the bits that correspond to the dots that are not printed are...
Page 71 - ESC u 1; ESC u 0
3-63 STAR Command Specifications Rev. 0.70 ESC u 1 [Name] Specify 16 x 16 dot [single density] Kanji characters. [Code] ASCII ESC u 1 Or ESC u “1” Hexadecimal 1B 75 01 1B 75 31 Decimal 27 117 1 27 117 149 [Defined Area] --- [Initial Value] Specify two-byte 16 x 16 dot (single density) Kanji characte...
Page 72 - ESC x 1; ESC x 0
3-64 STAR Command Specifications Rev. 0.70 ESC x 1 [Name] Specify two byte Kanji characters (cancel expanded Kanji characters) [Code] ASCII ESC x 1 Or ESC x “1” Hexadecimal 1B 78 01 1B 78 31 Decimal 27 120 1 27 120 49 [Defined Area] --- [Initial Value] Specify two-byte 16 x 16 dot (single density) K...
Page 73 - ESC w 1; ESC w 0
3-65 STAR Command Specifications Rev. 0.70 ESC w 1 [Name] Specify two-byte 16 x 16 dot Kanji characters [Single Density] (Default) [Code] ASCII ESC w 1 Or ESC w “1” Hexadecimal 1B 77 01 1B 77 31 Decimal 27 119 1 27 119 49 [Defined Area] --- [Initial Value] Specify two-byte 16 x 16 dot (single densit...
Page 75 - RS; CAN
3-67 STAR Command Specifications Rev. 0.70 3-3-15 Others RS [Name] Ring buzzer [Code] ASCII RS Hexadecimal 1E Decimal 30 [Defined Area] --- [Initial Value] --- [Function] Issues a short buzzer sound from the printer. CAN [Name] Cancel print data and initialize commands [Code] ASCII CAN Hexadecimal 1...
Page 77 - ESC U n
3-69 STAR Command Specifications Rev. 0.70 ESC @ [Name] Command initialization [Code] ASCII ESC @ Hexadecimal 1B 40 Decimal 27 64 [Defined Area] --- [Initial Value] --- [Function] Initializes each command after printing data in the line buffer. DIPSW and memory switch re-read is not performed. The f...
Page 78 - ESC GS # m N n1 n2 n3 n4 LF NUL
3-70 STAR Command Specifications Rev. 0.70 ESC GS # m N n1 n2 n3 n4 LF NUL [Name] Set memory switch [Code] ASCII ESC GS # m N n1 n2 n3 n4 LF NUL Hexadecimal 1B 1D 23 m N n1 n2 n3 n4 0A 00 Decimal 27 29 35 m N n1 n2 n3 n4 10 0 [Defined Area] m = 87, 84, 44, 43, 45 (m = “W”, “T”, “,”, “+”, “-”) 48 ≤ N...
Page 79 - ESC # N m n1 n2 n3 n4 LF NUL
3-71 STAR Command Specifications Rev. 0.70 ESC # N m n1 n2 n3 n4 LF NUL [Name] Set memory switch [Code] ASCII ESC # N m n1 n2 n3 n4 LF NUL Hexadecimal 1B 23 N m n1 n2 n3 n4 0A 00 Decimal 27 35 N m n1 n2 n3 n4 10 0 [Defined Area] m = 44, 43, 45 (m = “,”, “+”, “-“) 48 ≤ N ≤ 57 (”0” ≤ N ≤ “9”), 65 ≤ N ...
Page 81 - -4 Black Mark Related Commands; Top of form (black mark detection) operation
3-73 STAR Command Specifications Rev. 0.70 3-4 Black Mark Related Commands The Star black mark related commands are to control the top of form (black mark) functions.This commands are effective only when black mark function is valid. <Black mark specifications> 1. Top of form (black mark detec...
Page 86 - ESC RS m n
3-78 STAR Command Specifications Rev. 0.70 ESC RS m n [Name] Enable, disable black mark detection [Code] ASCII ESC RS m n Hexadecimal 1B 1E 6D n Decimal 27 30 109 n [Defined Area] n = 0, 1, 2, 48, 49, 50 [Initial Value] Memory SW [Function] Switchest to enable/disable black mark (BM) detection contr...
Page 87 - -5 USB Related Commands; The following commands control USB interface functions.
3-79 STAR Command Specifications Rev. 0.70 3-5 USB Related Commands The following commands control USB interface functions.
Page 88 - ESC RS C n
3-80 STAR Command Specifications Rev. 0.70 3-6 2-Color Printing Command Details ESC RS C n [Name] Select/cancel 2-color printing mode [Code] ASCII ESC RS C n Hexadecimal 1B 1E 43 n Decimal 27 30 67 n [Defined Area] 0 ≤ n ≤ 1 48 ≤ n ≤ 49 (“0” ≤ n ≤ “1”) [Initial Value] DIP switch [Function] n Select/...
Page 90 - CHARACTER CODE TABLE; See the character code specifications
4-1 STAR Command Specifications Rev. 0.70 4. CHARACTER CODE TABLE See the character code specifications
Page 91 - -1 Status Specifications
5-1 STAR Command Specifications Rev. 0.70 5. APPENDIX 5-1 Status Specifications This function is effective only when using an interface capable of bi-directional data communications.Refer to your printer’s product specification manual to verify if the interface cable on the printer you use is capabl...
Page 97 - Interfaces; Printer Status
5-7 STAR Command Specifications Rev. 0.70 5-1-4 Printer Status Transmission Specification when using Ethernet and Wireless LAN Interfaces The following explains the printer status transmission specification when using Ethernet and wireless LAN interfaces. 1) Transmission Format: • When transmitting ...
Page 99 - -2 Expansion Position; Normal Dot
5-9 STAR Command Specifications Rev. 0.70 5-2 Expansion Position 5-2-1 7 x 9 Fonts 5-2-2 5 x 9 (2P-1) Fonts 㩷 㩷 㩷 Head Pin No. Head Pin No. Normal Dot Normal 7 x 9 Double high 7 x 9 Bit Image Half Dot #1#2#3 #4#5#6 #7#8 #9 #1#2#3 #4#5#6 #7#8 #9#1#2#3 #4#5#6 #7#8 #9 Head Pin No. 㩷 Head Pin No. Normal...
Page 101 - SPECIAL APPENDIX COMMAND LIST BY MODEL
6-1 STAR Command Specifications Rev. 0.70 6. SPECIAL APPENDIX COMMAND LIST BY MODEL • Standard Commands Class Commands Model Name BD100 SP2000 BD500 SP500 SP700 Font Styleand Character Set ESC GS t ○ Spec. 1 ○ Spec. 1 ○ Spec. 1 ○ Spec. 1 ○ Spec. 2 ESC R ○ ○ ○ ○ ○ ESC / ○ ○ ○ ○ ○ ESC 6 ○ ○ ○ ○ ○ ESC ...
Page 103 - Model Name
6-3 STAR Command Specifications Rev. 0.70 Class Commands Model Name BD100 SP2000 BD500 SP500 SP700 Others RS ○ ○ ○ ○ ○ CAN ○ ○ ○ ○ ○ DC3 ○ ○ ○ ○ ○ DC1 ○ ○ ○ ○ ○ ESC @ ○ ○ ○ ○ ○ ESC U ○ ○ ○ ○ ○ ESC GS # - - ○ ○ ○ ESC # ○ ○ Ignored Ignored Ignored ESC ? ○ ○ ○ ○ ○ • Black Mark Related Commands Class Co...
Page 104 - ELECTRONIC PRODUCTS DIVISION; OVERSEAS SUBSIDIARY COMPANIES
200 8 . 01 . 10 Printed in Japan , 8087 4545 ELECTRONIC PRODUCTS DIVISION STAR MICRONICS CO., LTD. 536 Nanatsushinya, Shimizu-ku, Shizuoka, 424-0066 Japan Tel: (int+81)-54-347-0112, Fax: (int+81)-54-347-0709 Please access the following URL http://www.star-m.jp/eng/dl/dl02.htm for the latest revision...
