South Bend SB1051 - Manual

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -5- I N T R O D U C T I O N Basic Controls Refer to Figures 2–7 and the following descriptions to become familiar with the basic controls of this lathe. Many of the controls will be explained in greater depth later in this manual. M...

-6- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe I N T R O D U C T I O N Control Panel L. 4-Way Tool Post: Mounts up to four cutting tools at once that can be individually indexed to the workpiece. M. Compound Rest Handwheel: Moves the tool toward and away from the workpiece a...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -7- I N T R O D U C T I O N Tailstock W. Quill: Moves toward and away from the spindle and holds centers and tooling. X. Quill Lock Lever: Secures the quill in position. Y. Tailstock Lock Lever: Secures the tailstock in position alo...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -11- S A F E T Y Understanding Risks of Machinery Operating all machinery and machining equipment can be dangerous or relatively safe depending on how it is installed and maintained, and the operator's experience, common sense, risk...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -13- S A F E T Y Additional Metal Lathe Safety Clearing Chips. Metal chips can easily cut bare skin—even through a piece of cloth. Avoid clearing chips by hand or with a rag. Use a brush or vacuum to clear metal chips. Stopping Spin...

-14- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe S A F E T Y Additional Chuck Safety Entanglement. Entanglement with a rotating chuck can lead to death, amputation, broken bones, or other serious injury. Never attempt to slow or stop the lathe chuck by hand, and always roll u...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -15- P R E P A R A T I O N Preparation Overview Things You'll Need To complete the preparation process, you will need the following items: For Lifting and Moving s !FORKLIFTOROTHERPOWERLIFTINGDEVICE rated for at least 25% more than ...

-16- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N Power Supply Requirements Availability The full-load current rating is the amperage a machine draws at 100% of the rated output power. On machines with multiple motors, this is the amperage drawn by the la...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -17- P R E P A R A T I O N Extension Cords Grounding Requirements Improper connection of the equipment-grounding wire can result in a risk of electric shock. The wire with green insulation (with or without yellow stripes) is the equ...

-18- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N Unpacking This item was carefully packaged to prevent damage during transport. If you discover any damage, please immediately call Customer Service at (360) 734-1540 for advice. You may need to file a frei...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -19- P R E P A R A T I O N The unpainted surfaces are coated at the factory with a heavy-duty rust preventative that prevents corrosion during shipment and storage. The benefit of this rust preventative is that it works very well. Th...

-20- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N Children or untrained people may be seriously injured by this machine. Install machine in an access restricted location. Space Allocation Consider the largest size of workpiece that will be processed throu...

-22- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N 8. Raise the lathe a couple of inches and check the balance of the load. — If the load is not safely balanced, immediately lower the lathe and resolve the issue before attempting to lift it again. 9. Raise...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -23- P R E P A R A T I O N Assembly With the exception of the handwheel handles, the lathe is shipped fully assembled. To install the handwheel handles, thread the large handle into the carriage handwheel and the small handle into t...

-24- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N Besides adding oil to the reservoirs, we also recommend that you lubricate other points on the lathe at this time. This can be accomplished by following the Lubrication section beginning on Page 64 . Note:...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -25- P R E P A R A T I O N Test Run After all preparation steps have been completed, the machine and its safety features must be tested to ensure correct operation. If you discover a problem with the operation of the machine or its ...

-30- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Operation Overview To complete a typical operation, the operator does the following: 1. Puts on safety glasses, rolls up sleeves, removes jewelry, and secures any clothing, jewelry, or hair that could get enta...

-32- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Chuck Installation Figure 27. Inserting camlock studs into spindle cam holes. INCORRECT CORRECT 5. Incrementally tighten the camlocks in a criss-cross or star pattern to ensure that the chuck seats evenly agai...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -33- O P E R A T I O N Figure 30. Registration mark locations. CamlockSpindle 2-Piece Direct Mount Camlock Chuck Marks for Chuck Reassembly ChuckHalves Spindle & Chuck Registration Marks Registration Marks Lightly stamp registra...

-34- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Scroll Chuck Clamping This scroll-type chuck has an internal scroll-gear that moves all jaws in unison when adjusted with the chuck key. This chuck will hold cylindrical parts on-center with the axis of spindl...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -35- O P E R A T I O N Figure 33. 4-jaw tightening sequence. 1 2 3 4 Workpiece Center Point 5. Tighten each jaw in small increments. After you have adjusted the first jaw, continue tightening the remaining jaws in an opposing sequen...

-36- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N To mount a non-concentric workpiece to the faceplate: 1. DISCONNECT LATHE FROM POWER! 2. Protect the bedway with a piece of plywood. 3. With help from another person or a holding device to support the workpiec...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -37- O P E R A T I O N Installing Tooling This tailstock uses a quill with an MT#5 taper that has a lock slot in the back of the bore that accepts tang arbors and drill bits (see Figures 37–38 for examples). Figure 37. Types of tape...

-38- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Removing Tooling 1. Use a shop rag to hold the tool. 2. Rotate the quill handwheel counterclockwise until the tool is forced out of the quill. — If the tool does not come loose by retracting the quill, extend ...

-40- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Note: If necessary in the following step, refer to Offsetting Tailstock on Page 38 for detailed instructions. 8. Use calipers to measure both ends of the workpiece. — If the test stock is thicker at the tailst...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -41- O P E R A T I O N Live Centers A live center has bearings that allow the centertip and the workpiece to rotate together; it can beinstalled in the spindle and the tailstock quill forhigher speeds. However, a live center typical...

-42- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N 3. Use the quill handwheel to feed the quill out from the casting approximately 1". Note: Do not extend the quill more than 2" or stability and accuracy will be reduced. 4. Insert the center into the t...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -43- O P E R A T I O N The steady rest supports long shafts and can be mounted anywhere along the length of the bedway. Familiarize yourself with the steady rest components shown in Figure 51 to better understand its operation. Stea...

-44- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Follow Rest The follow rest mounts to the saddle with two cap screws (see Figure 53 ). It is used on long, slender parts to prevent workpiece deflection from the pressure of the cutting tool during operation. ...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -45- O P E R A T I O N The four-way tool post is mounted on top of the compound rest and allows a maximum of four tools to be loaded simultaneously. Each tool can be quickly indexed to the workpiece by loosening the top handle, rota...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -47- O P E R A T I O N Micrometer Stop 3. Move the micrometer stop up to the carriage, use the graduated dial to fine tune the position, then retighten the cap screws loosened in Step 2 . 4. Verify that tooling will not make contact...

-48- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Manual Feed The handwheels shown in Figure 62 allow the operator to manually move the cutting tool. Carriage Handwheel The carriage handwheel moves the carriage left or right along the bed. It has a graduated ...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -49- O P E R A T I O N Setting Spindle Speed Setting the spindle speed requires positioning the spindle speed range lever to either the high or low range, then using the spindle speed dial to set the speed, using the digital readout...

-50- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Power Feed Controls Use Figures 65–66 and the following descriptions to become familiar with the locations and functions of the power feed controls. Note: Before using power feed, you may have to re-configure ...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -51- O P E R A T I O N Figure 66. Apron power feed controls. E F E. Feed Selection Lever: Engages the power feed for either the cross slide or the carriage (see Figure 67 ). Setting Power Feed Rate The feed rate chart on the upper r...

-52- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Note: In the next step, use the chuck key to rock the spindle back-and-forth to help mesh the gears as you make adjustments. 4. Position the controls as directed by the configuration string as follows (see Fig...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -53- O P E R A T I O N Alternate Configuration Use the alternate end gear configuration for cutting modular or diametral threads. The 57T end gear is positioned on the outside so that it meshes with the 44T transposing gear instead o...

-54- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N The following subsections describe how to use the threading controls and charts to set up the lathe to cut threads. If you are unfamiliar with how to cut threads on a lathe, we strongly recommend that you read...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -55- O P E R A T I O N Apron Threading Controls The half nut lever (see Figure 74 ) engages the carriage with the leadscrew, which moves the carriage and cutting tool along the length of the workpiece for threading operations. Impor...

-56- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N Figure 78. Marks are selected on the dial for threading even TPI not divisible by 4. Non-Numbered Position 2,6,10,14,18,22,26,30,54 TPI Thread Dial Chart The thread dial chart (see Figure 76 ) can be found on ...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -57- O P E R A T I O N 1 ⁄ 4 or 3 ⁄ 4 Fractional TPI For TPI that have a 1 ⁄ 4 or 3 ⁄ 4 fraction, use position 1 on the thread dial (see Figure 81 ). 2 7 ⁄ 8 TPI The thread dial is not used for 2 7 ⁄ 8 threads (see Figure 82 ). For ...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -59- A C C E S S O R I E S Accessories This section includes the most common accessories available for your lathe, which may be available through your local South Bend Lathe Co. dealer. If you do not have a dealer in your area, plea...

-62- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E Maintenance Schedule Cleaning & Protecting Regular cleaning is one of the most important steps in taking care of this lathe. We recommend planning a cleaning routine into the workflow schedule, so that...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -63- M A I N T E N A N C E Once every year, or more often with heavy use, perform these service items. Keep track of when you last performed your annual service and when you’ll need to perform it again. Use this chart to keep track ...

-66- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E 9. Clean away grime and debris from the oil tank access cover (see Figure 100 ), then unthread the four cap screws to remove the cover. 10. Using mineral spirits and shop rags, thoroughly clean the inside ...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -67- M A I N T E N A N C E Adding Oil Use a 12mm wrench to remove the gearbox fill plug (see Figure 103 ). Add oil until the oil sight glass is approximately halfway full. Figure 103. Locations of the quick-change gearbox fill and d...

-68- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E One- Shot Oiler The one-shot oiler shown in Figure 107 lubricates the saddle ways with oil from the apron reservoir. To use the one-shot oiler, pull the pump knob out for two or three seconds and then push...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -69- M A I N T E N A N C E Ball Oilers & Oil Cup Oil Type .. Mobil DTE Light or ISO 32 EquivalentOil Amount ................................ 1 or 2 Squirts/FillLubrication Frequency ................................... Daily This...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -71- M A I N T E N A N C E Coolant System Service The coolant system consists of a fluid tank, pump, and flexible nozzle. The pump pulls fluid from the tank and sends it to the valve, which controls the flow of coolant to the nozzle...

-72- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E To change the coolant: 1. Position the coolant nozzle over the back of the backsplash so that it is pointing behind the lathe. 2. Place the 5-gallon bucket behind the lathe and under the coolant nozzle. If...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -73- M A I N T E N A N C E 9. Slide the tank partially into the base and re- connect the fluid hose. Tip: Leave one or more magnets at the bottom of the tank to collect metal chips and make cleanup easier next time. This will also h...

-74- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe S E R V I C E Cross Slide Tools Needed: Qty Hex Wrench 3mm ................................................. 1Hex Wrench 5mm ................................................ 1 The cross slide backlash is adjusted by loosening a...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -75- S E R V I C E Gib Adjustment The goal of adjusting the gib screws is to remove sloppiness or "play" from the ways without over-adjusting them to the point where they become stiff and difficult to move. In general, loose...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -77- S E R V I C E Half Nut Adjustment The clamping pressure of the half nut is fully adjustable with a gib that can be loosened or tightened by two set screws. Use this procedure to adjust the half nut if it becomes loose from wear...

-82- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe S E R V I C E 5. Install all fasteners and lightly snug them in place. 6. Mount a dial indicator with a magnetic base to the top of the saddle to indicate alignment. 7. First test the peak of the two prisms of the gap insert th...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -83- T R O U B L E S H O O T I N G If you need replacement parts, or if you are unsure how to do any of the solutions given here, feel free to call us at (360) 734-1540. Symptom Possible Cause Possible Solution Machine does not star...

-86- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this secti...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -87- E L E C T R I C A L Machine Electrical Overview Work Light (Page 97) Spindle Motor (Page 95) Coolant Pump Motor (Page 95) Oil Pump Motor (Page 96) Oil Pressure Sensor (Page 96) Resistor (Page 90) RPM Display (Page 90) Electrica...

-88- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L Electrical Component Location Index Work Light (Page 97) Control Panel (Page 94) Brake Switch (Page 97) RPM Display & Resistor (Page 90) Spindle Switches (Page 96, Behind Splash Guard) Oil Pressure Senso...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -89- E L E C T R I C A L Electrical Cabinet Overview F1 Circuit Breaker 24V ( Page 91 ) F2 Spindle Motor Overload Relay ( Page 91 ) F3 Oil Pump Motor Overload Relay ( Page 91 ) F4 Circuit Breaker 6A ( Page 91 ) F5 Fuse 4A ( Page 91 ...

-90- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L RPM Display Cabinet Overview RPM Display Cabinet Wiring Diagram (RPM & RES) RPM N1 B2 TB K TB L13 TB L11 TB L TB COM N1 B1 1 2 3 4 5 6 7 8 9 RES RPM Display Resistor RT LT Figure 140. RPM cabinet compone...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -91- E L E C T R I C A L Upper Electrical Cabinet Wiring Diagram 97 .25 .3 .35 .4 98 NO NC 1L1 5L3 7L4 8T4 3L2 95 96 2T1 4T2 6T3 A1 A2 O R 97 .25 .3 .35 .4 2T1 6T3 98 NO NC 4T2 1L1 5L3 7L4 8T4 3L2 95 96 2T1 4T2 6T3 A1 A2 O R Q1 K1 K...

-94- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L Control Panel Overview Control Panel Wiring Diagram TB 3 TB TB 4 TB 1 PCB 1 PCB PCB 20 PCB JOG PCB 2 PCB 3 Control Panel (Viewed from Behind) Spindle Speed Dial Power Light Coolant Pump Switch Jog Button STO...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -95- E L E C T R I C A L Spindle Motor Wiring Ground L11 L13 W5 W2 U5 U2 V2 V5 V6 W1 U6 V1 U1 W6 W V U Ground Ground V1 U1 W1 6 4 5 3 2 1 Coolant Pump Motor Wiring Figure 143. Coolant pump junction box. Figure 142. Spindle motor jun...

-96- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L Ground U2 U2 U5 U1 V1 V5 W1 W5 W2 W2 V2 V2 Bk Wt 2 11 Oil Pressure Sensor Spindle Switch Wiring Oil Pump Motor & Pressure Sensor Wiring Figure 144. Spindle switch wiring. 7 6 6 8 9 COM COM NO NO NC NC Fi...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -97- E L E C T R I C A L Work Light Chuck Guard Safety Switch End Cover Safety Switch Brake Switch 9 0 1 A1 0 2 COM NO NC NC NO 3 NC 14 22 13 21 NO 4 5 3 A1 Additional Component Wiring Power Supply Connection (PS) Ground Hot Hot Hot...

-98- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Headstock Cover 1 2 3 4 REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 1 PSB10 5 10001 OIL C A P 3 PSB10 5 10003 HE A DSTOCK TOP COVER 2 PC A P29M C A P SCREW M6-1 X 40 4 PSB10 5 10004 TOP COVER G A SKET

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -99- P A R T S Headstock Controls 5 6 7 9 9 9 10 11 12 20 20 21 21 22 23 24 25 26 27 28 28 28 28 39 29 30 30 30 30 31 34 35 36 37 38 40 41 42 42 43 43 44 44 45 46 47 47 48 48 49 49 49 49 50 50 51 51 52 52 53 53 54 54 54 54 55 56 57 ...

-100- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Headstock Controls Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 5 PSB10 5 1000 5 OIL TUBE 6 X 2 7 0MM 38 PC A P01M C A P SCREW M6-1 X 16 6 PW04M FL A T W A SHER 10MM 39 PSB10 5 10039 END PLUG 7 PSB10 ...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -101- P A R T S Headstock Internal Gears 38 38 38 61 62 63 64 71 72 73 74 74 75 75 75 76 77 81 82 83 83 84 85 86 88 90 91 92 93 94 95 96 97 98 99 100 101 102 103 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117

-102- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Headstock Internal Gears Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 38 PC A P01M C A P SCREW M6-1 X 16 9 5 PR38M INT RET A INING RING 62MM 61 PSB10 5 10061 OIL SE A L 30 X 62 X 12MM 96 PSB10 5 10096...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -103- P A R T S Headstock Transfer Gears 10 10 10 24 30 33 38 38 38 83 83 85 121 122 123 124 125 126 126 127 130 130 130 131 132 132 132 133 136 136 136 137 138 139 141 142 142 143 144 145 147 149 148 REF P A RT # DESCRIPTION REF P ...

-104- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Gearbox Gears 201 202 203 203 204 205 206 206 206 206 206 206 207 208 209 210 211 211 212 213 214 215 216 217 218 219 220 221 221 221 222 223 224 224 224 225 225 225 225 225 225 226 226 226 227 228 229 230 231 232 23...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -105- P A R T S Gearbox Gears Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 201 PSB10 5 10201 SPLINE SH A FT 232 PSB10 5 10232 GE A R 19T 202 PSB10 5 10202 OIL SE A L 20 X 32 X 5 233 PSB10 5 10233 GE A R 20T 203 PSB10...

-106- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Gearbox Controls 262 263 264 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 282 283 284 288 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -107- P A R T S Gearbox Controls Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 262 PSB10 5 10262 FRONT COVER G A SKET 301 PSB10 5 10289 WOODRUFF KEY 4 X 13 263 PSB10 5 10263 J A CKSCREW 302 PSB10 5 10302 SHIFT SH A FT...

-108- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Apron Front View 401 402 402 403 404 405 406 407 408 409 410 411 412 413 414 414 414 415 416 417 418 419 420 421 422 422 423 424 425 426 427 428 429 430 431 432 434 435 437 438 439 440 441 442 444 445 446 447 448 449...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -109- P A R T S Apron Front View Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 401 PSB10 5 10401 COMBO GE A R 18T/60T 429 PORP026 O-RING 2 5 . 7 X 3. 5 P26 402 PSB10 5 10402 THRUST W A SHER A S304 7 430 PSB10 5 10430 ...

-110- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Apron Rear View REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 414 PSTB001 STEEL B A LL 1/4" 4 7 0 PSB10 5 104 7 0 COMPRESSION SPRING 6 X 2 7 422 PSB10 5 10422 GE A R 18T 4 7 2 PRP04M ROLL PIN 4 X 24 434 PORP0...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -111- P A R T S REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 5 01 PSB10 5 10 5 01 LEVER 5 1 7 PSB10 5 10 5 1 7 INDIC A TOR PL A TE 5 02 PSB10 5 10 5 02 TOOL POST NUT 5 18 PSB10 5 10 5 18 LE A DSCREW BR A CKET 5 03 PSB10 5 10 5 ...

-112- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Saddle Top View 601 601 601 601 602 603 604 605 606 607 608 608 609 609 610 611 612 613A 613 614 615 616 617 618 619 620 620 621 621 622 623 624 624 625 625 626 627 628 628 629 629 630 630 631 632 633 634 635 636 637...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -113- P A R T S Saddle Top View Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 601 PSB10 5 10601 GIB A DJUSTMENT SCREW 628 PSTB001 STEEL B A LL 1/4" 602 PSB10 5 10602 CROSS SLIDE 629 PSB10 5 10629 COMPRESSION SPRIN...

-114- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 641 PSB10 5 10641 SP A CER 6. 5 X 1 5 X 3 649 PSB10 5 10649 OIL TUBE 6 X 160MM 642 PSB10 5 10642 GE A R 16T 6 5 0 PSB10 5 106 5 0 STR A IGHT A D A PTER 1/8"PT X 6...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -115- P A R T S Micrometer Stop 701 702 700 703 704 705 706 707 708 709 710 711 712 REF P A RT # DESCRIPTION 7 00 PSB10 5 10 7 00 MICROMETER STOP A SSEMBLY 7 01 PC A P 7 1M C A P SCREW M10-1. 5 X 60 7 02 PRIV009M STEEL FLUTED RIVET ...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -117- P A R T S Bed & Shafts Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 801 PSB10 5 10801 BED 83 7 PSB10 5 10836 A T A PERED BUSHING 802 PSB10 5 10802 C A RRI A GE STOP BOLT 838 PSB10 5 10836 A T A PER PIN #4 X...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -119- P A R T S Motor 1001 1002 1003 1004 1005 1005 1006 1007 1008 1008 1008 1009 1010 1011 1012 1013 1014 1014 1015 1015 1016 1017 1018 1019 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1028 1029 1030 1030 1031 1031 1032 1033 ...

-120- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Motor Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 1001 PSB10 5 11001 END GE A R COVER 102 5 PSB1039102 5 T A PER PIN #4 X 1-3/4 1002 PSB10 5 11002 KNURLED KNOB M10-1. 5 1026 PSB10 5 11026 BR A KE BR ...

-122- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Cabinets & Panels Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 1101 PSB10 5 11101 BR A KE PED A L ROD 112 7 PS6 5 M PHLP HD SCR M4-. 7 X 40 1102 PSB10 5 11102 BR A KE PED A L 1128 PN03M HEX NUT M8...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -123- P A R T S Headstock Lubrication System D D B B A A C C E E 1201 1202 1203 1204 1205 1206 1204 1206 1207 1208 1209 1210 1214 1215 1216 1217 1218 1219 1220 1221 1201 1222 1223 1224 1225 1225-1 1225-4 1225-2 1225-5 1225-3 1226 12...

-124- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Headstock Lubrication System Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 1201 PSB10 5 11201 OIL TUBE ELBOW A D A P A TER 3/8"PT X M6-1 122 5 PSB10 5 1122 5 LUBRIC A TION MOTOR 1/4HP 220V 3PH 1202...

-126- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Tailstock Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 1301 PSB10 5 11301 T A ILSTOCK LE A DSCREW 1332 PSB10 5 11332 V-W A Y WIPER 1302 PSB10 5 11302 LE A DSCREW NUT 1333 PSB10 5 11333 V-W A Y WIPER P...

-128- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Electrical Cabinets & Control Panel 1500 1501 1502 1503 1504 1504-1 1505 1505-1 1506 1507 1508 1509 1509 1510 1511 1512 1513 1514 1514 1514 1515 1516 1517 1518 1519 1520 1521 1522

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -129- P A R T S Electrical Cabinets & Control Panel Parts List REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 1 5 00 PSB10 5 11 5 00 RPM DISPL A Y NEWC A L SPP1406 1 5 11 PSB10 5 11 5 11 OL REL A Y A B 193T1 AA 40 2. 5 -0.4 A...

For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -131- P A R T S Front Machine Labels The safety labels provided with your machine are used to make the operator aware of the machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location a...

-132- For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe P A R T S Rear & Side Machine Labels 1619 1620 1620 1620 1621 1621 1624 1622 1622 1623 REF P A RT # DESCRIPTION REF P A RT # DESCRIPTION 1600 PSB10 5 11600 MODEL NUMBER BR A SS PL A TE 1613 PSB10 5 11613 M A CHINE ID L A B...

W A R R A N T Y This quality product is warranted by South Bend Lathe Company to the original buyer for one year from the date of purchase. This warranty does not apply to consumable parts, or defects due to any kind of misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenanc...