Smeg PGA64 - Manual - manualsarea.com

Page 2 - Contents

21 Contents THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS MAN-UAL. INSTRUCTIONS FOR THE USER: these instructions contain userrecommendations, a description of the controls and the correctprocedures for cleaning and mainten...

Page 3 - General instructions; INSTRUCTIONS FOR USE

General instructions 22 1. INSTRUCTIONS FOR USE THIS MANUAL CONSTITUTES AN INTEGRAL PART OF THE APPLIANCE. THISMANUAL CONSTITUTES AN INTEGRAL PART OF THE APPLIANCE. IT SHOULD BEKEPT INTACT AND AT HAND FOR THE APPLIANCE’S ENTIRE LIFE CYCLE.IT IS IMPORTANT TO CAREFULLY READ THIS MANUAL AND ALL THEINST...

Page 5 - SAFETY PRECAUTIONS

General instructions 24 2. SAFETY PRECAUTIONS REFER TO THE INSTALLATION INSTRUCTIONS FOR THE SAFETY REGULATIONSFOR ELECTRIC OR GAS APPLIANCES AND VENTILATION FUNCTIONS.IN YOUR INTERESTS AND FOR YOUR SAFETY THE LAW REQUIRES THAT THEINSTALLATION AND SERVICING OF ALL ELECTRICAL APPLIANCES IS CARRIEDOUT...

Page 7 - Instructions for disposal; ENVIRONMENTAL RESPONSIBILITY; Our environmental responsibility; Your old appliance also needs to be disposed of correctly.; Important; : hand over your appliance to the local agency authorised for the

Instructions for disposal 26 3. ENVIRONMENTAL RESPONSIBILITY 3.1 Our environmental responsibility Pursuant to Directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating tothe reduction of the use of hazardous substances in electrical and electronicappliances, as well as to the disposal of refuse, th...

Page 8 - Instructions for the user; Lighting the hob burners; maximum flame symbol

Instructions for the user 27 4. USING THE HOB 4.1 Lighting the hob burners Before lighting the hob burners, check that the flame-spreader crowns arecorrectly in place with their respective burner caps, making sure that the holes A in the flame-spreaders are aligned with the igniters and thermocouple...

Page 9 - Practical tips for using the burners; HOB BURNER

Instructions for the user 28 4.2 Practical tips for using the burners For better burner efficiency and to minimise gas consumption, use pans with aflat, smooth base and a lid that have a suitable size for the burner, thuspreventing the flames reaching the sides of the pan (see paragraph “4.3 PanDiam...

Page 10 - CLEANING AND MAINTENANCE; NEVER USE A STEAM JET FOR CLEANING THE APPLIANCE.; Cleaning stainless steel; only; Cleaning the cooking hob parts; completely

Instructions for the user 29 5. CLEANING AND MAINTENANCE Before performing any operations requiring access to powered parts,switch off the power supply to the appliance. NEVER USE A STEAM JET FOR CLEANING THE APPLIANCE. 5.1 Cleaning stainless steel To keep stainless steel in good condition it should...

Page 11 - Instructions for the installer; POSITION NEAR THE COUNTER TOP; Fixing to a support structure model with traditional casing; mm; from the rear edge. This appliance can

Instructions for the installer 30 6. POSITION NEAR THE COUNTER TOP The following operation requires building and/or carpentry work so must be carried out bya competent tradesman.Installation can be carried out on various materials such as masonry, metal, solid wood orplastic laminated wood as long a...

Page 12 - Fixing to the electric model support structure

Instructions for the installer 31 6.2 Fixing to the electric model support structure Create an opening with the dimensionsshown in the figure in the top surface of thecounter, keeping a minimum distance of 50mm from the rear edge.The lower part of the casing must be fullyaccessible after the applian...

Page 14 - Electrical connection; Avoid the use of adapters and shunts.

Instructions for the installer 33 6.3 Electrical connection Make sure that the voltage and capacity of the power line conform to the datashown on the plate located under the casing. Do not remove this plate for anyreason. The plug at the end of the supply cable and the wall socket must be of the sam...

Page 15 - Ventilation in the premises.

Instructions for the installer 34 6.4 Ventilation in the premises. The room containing the appliance should have a permanent air supply inaccordance with the standards in force. The room where the appliance isinstalled must have enough air flow needed for the regular combustion of gasand the necessa...

Page 16 - Gas connection

Instructions for the installer 35 6.6 Gas connection Connection to the gas supply network can be made using a rigid copper hose ora flexible steel hose with a continuous wall and in compliance with the guidelinesestablished by the applicable standard. Once the operation is complete, check the hose f...

Page 17 - ADAPTATION TO DIFFERENT TYPES OF GAS; Replacement of the cooking hob nozzles; Unscrew the burner nozzles with a 7 mm socket spanner

Instructions for the installer 36 7. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from thepower supply. The appliance is preset for natural gas G20 (2H) at a pressure of 20 mbar. In thecase of operation with other types of gas, the burne...

Page 18 - Burner and nozzle characteristics table; HOB

Instructions for the installer 37 7.2 Burner and nozzle characteristics table Burner Rated heating capacity (kW) LPG – G30/G31 28/37 mbar Nozzle diameter 1/100 mm By-pass mm 1/100 Rated capacity (W) Rated g/h G30 Rated g/h G31 Auxiliary (1) 1.05 50 28 400 76 75 Rapid (2) 2.50 79 42 800 182 179 Ultra...

Page 19 - Adjusting the minimum for town and natural gas; This procedure must be carried

Instructions for the installer 38 8. FINAL OPERATIONS After making the adjustments described above, reassemble the appliance byfollowing in reverse the instructions reported in paragraph "7.1 Replacement ofthe cooking hob nozzles". After adjustment with a gas other than the preset one, repla...

Smeg PGA64 - Manual

Table of Contents:

Other Manuals for Smeg PGA64

Summary

Other Smeg Hobs Models