Smeg CIR60X3- User Manual

Page 2 - Introduction; INSTRUCTIONS FOR SAFE AND PROPER USE

Introduction 1. INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE C...

Page 4 - Instructions for the installer; POSITIONING OF HOB; It is the law that all gas appliances are installed by; Attachment to support structure

Instructions for the installer 6 2. POSITIONING OF HOB It is the law that all gas appliances are installed by authorised persons . Clearance around the appliance must comply with the requirements of AS5601. The following operation requires building and/or carpentry work so must be carried out by a c...

Page 6 - Clearance above and around domestic appliances; REQUIREMENTS

Instructions for the installer 8 2.2 Clearance above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measurement A) Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance bet...

Page 7 - 0 mm or more, or the horizontal surface shall be above the

Instructions for the installer Where B, measured from the periphery of the nearest burner to any vertical combustible surface , is less than 200 mm, the surface shall be protected in accordance with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for the full dimension (width or ...

Page 8 - Room ventilation; for appliances not equipped with gas safety; Discharge of combustion products

Instructions for the installer 10 2.3 Room ventilation Caution – This hob may only be installed and operated in rooms permanently ventilated in accordance with current regulations. For proper operation of a gas appliance it is essential for the air necessary for combustion of the gas to be able to f...

Page 9 - GAS CONNECTION; annealed copper pipe or

Instructions for the installer 3. GAS CONNECTION This appliance is suitable for installation with Natural Gas or LPG (propane). Refer to page 12 for the relevant burner pressure and appropriate injector sizes. When the appliance is to be connected to Natural Gas then the pressure regulator supplied ...

Page 10 - ELECTRICAL CONNECTION; Do not use reducers, adapters or shunts.; The manufacturer will not be liable; for any damage to persons or

Instructions for the installer 12 4. ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same ...

Page 11 - ADAPTATION TO DIFFERENT TYPES OF GAS; Removing the hob; remove the screws and the nuts A that secure the burner supports; lift the hob from its seat

Instructions for the installer 5. ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspected for NG natural gas at a pressure of 1.0 kPa. For functioning with other types of gas the nozzles must...

Page 12 - Regulation for LPG

Instructions for the installer 14 5.2 Regulation for LPG Loosen screw A and push support B all the way. Use a double head wrench to remove nozzle C and assemble the suitable one, following the instructions indicated in the reference charts, with respect to the type of gas to use. The screwing torque...

Page 13 - Regulation for natural gas

Instructions for the installer 5.3 Regulation for natural gas The hob has been adjusted for natural gas at a pressure of 1.0kPa. To allow the unit to work back with this type of gas, after it has been adjusted for LPG, perform the same operations described in paragraph “6.2 Regulation for LPG”, but ...

Page 14 - FINAL OPERATIONS; Regulation of minimum for natural gas

Instructions for the installer 16 6. FINAL OPERATIONS Having carried out the above adjustments, reassemble the appliance following, backwards, the instructions in paragraph “6.1 Removing the hob”. 6.1 Regulation of minimum for natural gas Replace the components on the burner and slide the knobs on t...

Page 15 - Arrangement of burners on hob; Lubrification of gas taps

Instructions for the installer 6.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Rapid 4 Rapid 5 WOK 6.4 Lubrification of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-greased. This must be done by a qualif...

Page 16 - Instructions for the user; USING THE HOB; Ignition of the burners

Instructions for the user 18 7. USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted correctly. In the ultrarapid burner, notch A must be aligned with pin B . Grid C provided is intended for use with woks (Chinese pans). Adapter D comes only w...

Page 17 - Practical advice for using the burners; Electric elements; Turning on electric elements

Instructions for the user 7.2 Practical advice for using the burners For better burner performance and minimum gas consumption, flat bottomed, even recipients must be used, with covers and proportional in size to the burners (see paragraph “7.3 Diameter of containers”). To avoid overcooking or damag...

Page 18 - Using the electric elements; WARNING; To use correctly remember to:

Instructions for the user 20 7.4.2 Using the electric elements The electric elements are ideal for ultrarapid cooking. The settings shown in the table are merely indicative. POSITION HEAT INTENSITY POSSIBLE COOKING - 0 Off To melt butter, chocolate, etc. 1 Weak To heat small amounts of liquid. 2 Sof...

Page 19 - CLEANING AND MAINTENANCE; Cleaning; Never use a steam jet to clean the appliance.; Regular daily cleaning of the hob; Rinse thoroughly and dry with a soft cloth or deerskin.

Instructions for the user 8. CLEANING AND MAINTENANCE Before any intervention, disconnect the power supply of the device. 8.1 Cleaning Clean the cooking top regularly every time you use it, obviously after it has cooled. Never use a steam jet to clean the appliance. 8.1.1 Regular daily cleaning of t...

Page 20 - Cleaning of cooking hob components; CAUTION: do not wash these components in a dishwasher.; Ignition plugs and safety devices

Instructions for the user 22 8.2 Cleaning of cooking hob components CAUTION: do not wash these components in a dishwasher. In normal use of the hob, the stainless steel burner caps and pan-stands tend to be burnished by the high temperature. Clean these parts using very fine abrasive sponges or simi...

Page 21 - Preventive maintenance

Instructions for the user 8.3 Preventive maintenance This appliance does not need any special maintenance. However, a few simple operations have to be carried out periodically to prevent malfunctioning: Burners: the burners must be cleaned after every use to ensure correct combustion; make sure that...

Page 22 - PROBLEMS AND CAUSES; PROBLEM; Call Service Center.

Instructions for the user 24 9. PROBLEMS AND CAUSES Each of the following cases is caused by an abnormal operation of the appliance and should be dealt with by a authorised persons: please contact your local dealer or Service Center in case you detect any of these malfunctioning. PROBLEM CAUSE WHAT ...

Table of Contents:

Summary

Other Smeg Models