Siemens CP 343-1 - User Manual

Siemens CP 343-1

Siemens CP 343-1 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
Page: / 56

Table of Contents:

  • Page 2 – Notes on the Product; Product Names; Note; Note; Compatibility with the Previous Version; Note; Address label: Unique MAC address preset for the CP
  • Page 3 – Contents; Contents
  • Page 4 – Web Diagnostics
  • Page 5 – Properties / Services; Application
  • Page 7 – Configuration; Version STEP 7; Programming; Notice; current blocks in our Customer Support area on the Internet:
  • Page 8 – Requirements for Use; General Operation
  • Page 11 – Installation and Commissioning
  • Page 12 – Ground/Chassis Ground Concept; When shipped: Slider pushed in
  • Page 13 – requirements of at least IP54 in compliance with EN 60529.; Warning
  • Page 14 – Displays; SF; The LEDs have the following meaning:
  • Page 15 – LEDs for displaying the mode; RUN
  • Page 16 – LEDs for displaying the CP communication status
  • Page 17 – Performance Data; Number of Possible Connections over Ethernet; S7 connections; Characteristic Data for S7 Communication
  • Page 18 – Characteristics of the SEND/RECEIVE Interface; 00 CPU is the decisive factor.
  • Page 19 – Characteristic Data for PROFINET IO; CP as PROFINET IO device
  • Page 20 – Configuring and Programming the CP as a PROFINET IO Device; Configuring and Programming the CP as a; “Intelligent” PROFINET IO Device; Lean can be configured so that the SIMATIC 300 station can be; Overview of the Preparatory Steps
  • Page 21 – Principle of Data Exchange over PROFINET IO; Data Exchange between controller and CP as PROFINET IO device; transferred as an; entire area
  • Page 22 – PROFINET IO device mode in the properties dialog.; Installing the CP and Specifying it as PROFINET IO Device; Follow the steps below in STEP 7 / HW Config:
  • Page 23 – This name may only be assigned once in the PROFINET IO line.; Download the configuration data to the SIMATIC 300 station.
  • Page 24 – PROFINET IO Controller; Step 1: Configuring the PROFINET IO controller
  • Page 25 – PROFINET IO controller.
  • Page 26 – Step 3: Configuring the properties of the CP as PROFINET IO device; Continue configuration in HW Config as follows:; Deselect the “Assign IP address by IO controller” option.
  • Page 27 – No further parameter assignment of the modules is necessary.; operated without exception at 100 Mbps full duplex.; Interface for Programming on the PROFINET IO Device; FCs
  • Page 28 – Data consistency; Initialization and Configuration; Initialization; Length of the input data (when FC11 is called)
  • Page 29 – Reasons for reinitialization; configuration change.; Watchdog
  • Page 30 – Example of Configuration and Programming
  • Page 31 – Transfer the process inputs (DB10) to the I addresses with PNIO_SEND; The call interface PNIO_SEND in the user program
  • Page 32 – The call interface PNIO_RECV in the user program
  • Page 33 – Requirements and Use; Settings for Access to Diagnostic Data; Starting and Working with Web Diagnostics
  • Page 34 – Diagnostics Pages of the CP; Layout of the Diagnostics Pages
  • Page 35 – Start Page; Parameter
  • Page 37 – Rack Configuration
  • Page 39 – Diagnostic Buffer
  • Page 40 – Industrial Ethernet; “Parameters” Tab
  • Page 41 – “Statistics” Tab; “TCP Connections” Tab; This page informs you about existing TCP connections.; “UDP Connections” Tab; This page informs you about existing UDP connections.
  • Page 42 – PROFINET IO; Parameters of a PROFINET IO Device
  • Page 44 – Compatibility with Predecessor Products; Extended Functionality; New: Enhanced functions compared with module 6GK7 343; Replacing Older Modules / Replacing Faulty Modules; Use as a Replacement:
  • Page 45 – Module Replacement
  • Page 46 – Further Notes on Operation; Memory Reset; Available Functions; The CP has a two-level function available for resetting memory:; How to Use the Function; You can start the memory reset functions in STEP 7.
  • Page 47 – Behavior after Memory Reset; The configuration data must then be reloaded.; Working with Fast Ethernet; How Automatic Switchover of the Network Settings Works; 00 Mbps full duplex.; Autocrossing
  • Page 48 – Automatic Setting or Individual Network Settings
  • Page 49 – SNMP Agent; SNMP
  • Page 50 – Access Permissions using Community Name; Influence of MPI on Connections via Industrial Ethernet; MPI
  • Page 51 – 40 bytes is being processed are aborted temporarily.; Special Features of IP Configuration; over DHCP; Reserved Port Numbers
  • Page 52 – Obtaining the IP Address over DHCP; When the lease expires the reaction of the CP is as follows:; Other information available about the CP; FAQ
  • Page 53 – 0 How to Load New Firmware; Requirements; Requirements for Downloading; How to Download New Firmware; What to do if a Download is Interrupted
  • Page 54 – 1 Technical Specifications
Loading the manual

SIMATIC NET

S7-CPs for Industrial Ethernet

Manual Part B3L

CP 343-1 Lean

6GK7 343

−

1CX10

−

0XE0

as of hardware version 2, as of firmware version V2.0

for SIMATIC S7

−

300 / C7

−

300

Release 03/2007

C79000-G8976-C198-04

TP port:

2 x 8

−

pin RJ

−

45 socket

(beneath the front panel)

LED displays

X = Placeholder for hardware

version

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Notes on the Product; Product Names; Note; Note; Compatibility with the Previous Version; Note; Address label: Unique MAC address preset for the CP

Notes on the Product B3L − 2 CP 343-1 Lean for Industrial Ethernet / Manual Part B3L Release 03/2007 C79000-G8976-C198-04 Notes on the Product Product Names This description contains information on the following product S CP 343 − 1 Lean Order number 6GK7 343 − 1CX10 − 0XE0 as of hardware version 2 ...

Page 3 - Contents; Contents

Contents B3L − 3 CP 343-1 Lean for Industrial Ethernet / Manual Part B3L Release 03/2007C79000-G8976-C198-04 Contents Contents − Part A Ethernet CPs − General information see general part . . . . . . . . . . . . . . . . . . . Note Please remember that Part A of the device manual also belongs to the ...

Page 4 - Web Diagnostics

Contents B3L − 4 CP 343-1 Lean for Industrial Ethernet / Manual Part B3L Release 03/2007 C79000-G8976-C198-04 6.4.2 Initialization and Configuration B3L − 28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 Example of Configuration and Programming B3L − 30 . . . . . . . . . . . ...

Other Siemens Models