Shop Fox D4031 - Manual
Shop Fox D4031 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – D4031 Mortising Kit Instructions; Mounting the Cone; Inventory; Mounting the Fence; Figure 4
- Page 3 – Making a Mortise; opening is positioned toward the operator and is; Figure 5; then; Figure 6; resulting in excessive heat and damage to the tool.; Figure 7; Proper drill bit depth.
- Page 4 – Cut Sequence; Cutting mortises that are wider than the chisel must be; Figure 8; one possible sequence that will produce good results.; Figure
Introduction
The Model D4031 (
Figure 1
) Mortising Kit provides every-
thing needed to produce mortises with your drill press.
Inventory
(Figure 2)
A.
Cone .........................................................1
B.
Fence Assembly ............................................1
C.
Alignment Tool .............................................1
D.
Mortising Chisels ...........................................4
E.
T-Nuts .......................................................4
F.
Mounting Sleeves:
2.945" OD x 2.600" ID ..................................1
2.600" OD x 2.366" ID ..................................1
2.366" OD x 2.170" ID ..................................1
G.
Mounting Bushings:
2.600" OD x 2.000" ID ..................................1
2.600" OD x 1.880" ID ..................................1
2.600" OD x 1.570" ID ..................................1
H.
Hold-Down Rods............................................2
I.
Hold-Down ..................................................1
J.
Adjustable Handle .........................................2
K.
Rod ...........................................................1
Figure 1.
Model D4031.
Figure 2
. Inventory.
COPYRIGHT © JULY, 2010 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in China
#13055JB
Unplug your drill press before installing this mortising
attachment. Failure to do so may result in serious
personal injury.
Model D4031
Mortising Kit
Instruction Sheet
Phone #: (360) 734-3482 • Online Tech Support: [email protected] • Web: www.shopfox.biz
A
B
C
F
G
D
E
I
K
H
J
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2- D4031 Mortising Kit Instructions Mounting the Cone 1. If the cone will not fit over the drill chuck, remove the chuck. Otherwise, secure the alignment tool in the drill chuck on your drill press. 2. Carefully measure the flange on the bottom of the quill on your drill press. 3. Compare the size ...
-3- D4031 Mortising Kit Instructions Making a Mortise Proper alignment of the workpiece and chisel is essential to making good mortise and tenon joints. The instructions below describe one method of creating square joints with an evenly-spaced mortise. Place a scrap board on top of the drill press t...
-4- D4031 Mortising Kit Instructions REF PART # DESCRIPTION 1 XD4031001 ALIGNMENT TOOL 2 XD4031002 CLAMP ROD 3 XD4031003 LARGE T-NUT 5/16-18 4 XD4031004 SMALL T-NUT 5/16 X 18 5 XD4031005 FENCE 6 XD4031006 HOLD-DOWN ROD 7 XPW07 FLAT WASHER 5/16 8 XD4031008 HANDLE MALE 5/16-18 X 2" 9 XD4031009 HOL...
