Page 3 - IMPORTANT INFORMATION; RISK OF ELECTRIC; CAUTION
3 E IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFI...
Page 5 - Especially for child safety
5 E SAFETY PRECAUTIONS (Continued) 19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below: • Use the specif...
Page 6 - TIPS AND SAFETY INSTRUCTIONS
6 E - The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness....
Page 7 - MOUNTING PRECAUTIONS
7 E MOUNTING PRECAUTIONS • This product is for use indoors.• A mounting bracket compliant with VESA specifications is required. • Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor. • Mounting the monitor on the wall requires special expertise and the w...
Page 8 - Supplied Components; Contents
8 E Supplied Components If any component should be missing, please contact your dealer. Liquid Crystal Display Monitor: 1 Remote control unit: 1 Cable clamp: 2 Cable clamp (stick-on): 2 Power cord: 1 R-6 battery (“AA” size): 2 CD-ROM (Utility Disk for Windows): 1 Setup Manual: 1 Ve...
Page 9 - Front view; Part Names; Rear view
9 E n Front view 2 3 4 5 1 Accessing the operation panel 1. LCD panel 2. Remote control sensor (See page 15. ) 3. Input switch (See page 18. ) 4. Power switch (See page 16. ) 5. Power LED (See page 16.) TIPS • Use a pointed object such as a pen tip to press the switches. Part Names n Rear view 2 1 3...
Page 11 - Connecting Peripheral Equipment; Input mode; Connection with a PC or AV equipment
11 E 8 1 2 9 6 7 13 11 1210 5 3 4 Connecting Peripheral Equipment Caution • Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected. • Be careful not to confuse the input t...
Page 13 - Connecting the Power Cord
13 E Connecting the Power Cord Caution • Use only the power cord supplied with the monitor. 1. Turn off the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the AC power outlet. 1 Main power switch 2 AC input terminal For power o...
Page 14 - Binding Cables
14 E Binding Cables The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp. Insert the cable clamp into the cable clamp attachment on the rear of the monitor and fasten the cables. Cable clamp Cable Cable clamp attachment * Do not cover the vents. (1) (...
Page 15 - Preparing the Remote Control Unit; Installing the batteries; Remote control operation range; Operation panel in; Operation panel out
15 E Preparing the Remote Control Unit Installing the batteries 1. Press the cover gently and slide it in the direction of the arrow. 2. See the instructions in the compartment and put in the supplied batteries (R-6 (“AA” size) x 2) with their plus (+) and minus (-) sides oriented correctly. 3. Clos...
Page 16 - Turning on the main power
16 E Caution • Turn on the monitor first before turning on the PC or playback device. Turning on the main power Main power switch Caution • The main power must be turned on/off with the main power switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch...
Page 17 - Disabling power on/off operations
17 E Turning Power On/Off n Date/time setting • If the time has yet to be set when the monitor is first turned on, the date/time setting screen appears. Set the date and time. DATE/TIME SETTING / / OK···[ENTER] CANCEL···[RETURN] : : 01 01 13 / 12 AM 00 : / 20 1. Press or to select the date and time,...
Page 18 - Basic Operation
18 E Basic Operation 1 2 34 5 8 9 10 7 6 1. INPUT (Input mode selection) The menu is displayed. Press or to select the input mode, and press ENTER to enter. * You can select the input terminal by pressing the input switch of the monitor. Input mode Video Audio DVI-I DVI-I input terminal *4 DisplayPo...
Page 20 - Menu Items; Displaying the menu screen; Example of operation; Menu screen display
20 E Menu Items Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 20 to 29 for details of each menu items. Caution • Do not turn the main power switch off while the menu items are being dis...
Page 21 - Menu item details
21 E Menu item details The menu will differ depending on the input mode. n SCREEN You can move the menu screen display position each time DISPLAY is pressed. AUTO (D-SUB[RGB]/DVI-I (analog)) The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted.Pressing ENTER performs adjustment. Use this au...
Page 22 - PICTURE
22 E n PICTURE You can move the menu screen display position each time DISPLAY is pressed. BRIGHT Adjusts the backlight brightness. (In PIP mode, the main side setting is reflected in the image.) CONTRAST Adjusts the difference between the bright and dark portions of the image. BLACK LEVEL Adjusts t...
Page 24 - SETUP
24 E Menu Items n AUDIO TREBLE Adjusts the volume of treble-level sound. BASS Adjusts the volume of bass-level sound. BALANCE Adjusts the balance of the audio sound between right and left. RESET Resets the values of the AUDIO menu items to the factory preset values. Select “ON” and then press ENTER ...
Page 29 - Dual screen display; ZOOM2 SPECIAL SETTING
29 E n Dual screen display You can display two screens simultaneously. Set this function with PIP MODES of PIP/PbyP in the MULTI/ PIP menu. PIP Main screen Sub screen A sub screen is displayed inside a main screen. PbyP Main screen Sub screen A main screen and a sub screen are displayed in a line. P...
Page 31 - Adjustments for PC screen display; Automatic adjustment; Screen display for adjustment
31 E Adjustments for PC screen display n Automatic adjustment When you use the D-SUB[RGB] or DVI-I (analog) to display a PC screen for the first time, or when you change the setting of the PC, use the automatic screen adjustment. 1. Switch the input to D-SUB[RGB] or DVI-I (analog) and display the ad...
Page 33 - PC connection; Daisy chain connection...; Communication conditions; Command format
33 E Controlling the Monitor with a PC (RS-232C) You can control this monitor from a PC via RS-232C (COM port) on the PC. You can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 34), you can make input mode selection/adjustment or can...
Page 34 - Response code format; Communication interval; ID numbers
34 E Controlling the Monitor with a PC (RS-232C) n Response code format When a command has been executed correctly O K Return code (0D H , 0A H ) A response is returned after a command is executed. * If an ID number has been assigned O K SPC 0 0 1 ID number of responding monitor Space (20 H ) Return...
Page 35 - Commands for ID control
35 E Controlling the Monitor with a PC (RS-232C) n Commands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST ......... A monitor receiving this command sets its own ID number in the p...
Page 36 - Setting of the GAMMA user data
36 E Controlling the Monitor with a PC (RS-232C) n Repeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater control function without assigning ID numbers. [Examp...
Page 37 - RS-232C command table; Power control/Input mode selection
37 E RS-232C command table How to read the command table Command: Command field (See page 33.) Direction: W When the “Parameter” is set in the parameter field (see page 33), the command functions as described under “Control/Response Contents”. R The returned value indicated under “Reply” can be obta...
Page 39 - AUDIO menu
39 E Function Command Direction Parameter Reply Control/Response contents * ADVANCED AUTO AGIN W 1 When the input mode is D-SUB[RGB], DVI-I (analog). - ANALOG GAIN ANGA WR 0-127 0-127 When the input mode is D-SUB[RGB], DVI-I (analog). ○ ANALOG OFFSET ANOF WR 0-127 0-127 When the input mode is D-SUB[...
Page 40 - SETUP menu
40 E SETUP menu Function Command Direction Parameter Reply Control/Response contents * DATE/TIME SETTING DATE WR AABBCCDDEE AABBCCDDEE AA: Year, BB: Month, CC: Day, DD: Hour, EE: Minute ○ DATE DISPLAY FORMAT DTFT WR 0-2 0-2 0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY YYYY: Year, MM: Month, DD: Day T...
Page 41 - MONITOR menu
41 E Controlling the Monitor with a PC (RS-232C) MONITOR menu Function Command Direction Parameter Reply Control/Response contents * MONITOR STDR WR 0-1 0-1 0: LANDSCAPE, 1: PORTRAIT ○ OSD H-POSITION OSDH WR 0-100 0-100 OSD V-POSITION OSDV WR 0-100 0-100 STANDBY MODE STBM WR 0-1 0-1 0: STANDARD, 1: ...
Page 43 - OTHERS menu
43 E Function Command Direction Parameter Reply Control/Response contents * PIP MODES MWIN WR 0-3 0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2 ○ PIP SIZE MPSZ WR 1-64 1-64 PIP POS THE LONGEST DIRECTION MHPS W 0-100 R 0-100 THE SHORTEST DIRECTION MVPS W 0-100 R 0-100 PIP POS LD+SD BATCH MPOS W 0-100,0-100 S...
Page 45 - Initializing personal information; Settings to connect to a LAN; ■ To set on the monitor
45 E Your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. You can also configure the monitor to send e-mail notification when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through). Hub Network (LAN) L...
Page 46 - ■ To set from a PC; Set up process; (3) Configuring the monitor’s LAN settings
46 E ■ To set from a PC When the monitor is connected to a PC, LAN settings can be configured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC’s IP address (3) Configure the monitor’s LAN settings (1) Connecting your monitor to a PC Connect a commercially available crossove...
Page 47 - Controlling with a PC; ■ Basic operation
47 E 5. Click on “LAN SETUP” under NETWORK. 6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”. To set the address manually, set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set to ...
Page 48 - ■ INFORMATION; ■ CONTROL; ■ ADJUSTMENT
48 E ■ INFORMATION Information about this monitor appears. ■ CONTROL You can control the operations corresponding to the buttons ( POWER INPUT SIZE ) on the remote control unit. (See page 18.) TIPS • In standby mode, Power ON is the operation available. ■ ADJUSTMENT You can adjust these settings whi...
Page 52 - ■ SNMP; ■ SERVICE & SUPPORT
52 E Controlling the Monitor with a PC (LAN) ■ SNMP You can configure settings related to SNMP. SNMP SETTING Set whether to enable or disable SNMP. VERSION Set the version of the SNMP to be supported. COMMUNITY NAME 1 to 3 Set the name of the community required for the access. USER 1 to 3 Set the us...
Page 53 - (3) Disconnect the connection with the monitor and
53 E Controlling the Monitor with a PC (LAN) [Advanced operation] Command-based control You can control the monitor using RS-232C commands (see page 36) via terminal software and other appropriate applications. In order to use this function, enable a connection to the monitor through Internet Explor...
Page 54 - Troubleshooting
54 E Troubleshooting If you are experiencing any problem with your display, before calling for service, please review the following troubleshooting tips. There is no picture or sound. • Is the power cord disconnected? (See page 13.)• Is the main power switch off? (See page 16.)• Is the monitor in st...
Page 56 - Product Specifications
56 E Specifications n Product Specifications Model PN-R703 PN-R603 LCD component 70" Class [69-1/2 inch (176.6cm) diagonal] TFT LCD 60" Class [60-1/16 inch (152.5cm) diagonal] TFT LCD Max. resolution (pixels) 1920 x 1080 Max. colors Approx. 1.06 billion colors Pixel pitch 0.802 mm (H) × 0.80...
Page 58 - Power management
58 E n Power management This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in order for the monitor’s power management function to work. DPMS: Display Power Management Signaling DPMS Screen Power consumption *1 Hsync Vsync ON STATE Displ...
Page 60 - RS-232C input terminal pins
60 E Specifications n DVI-I input terminal pins (DVI-I 29 pin) No. Function No. Function 1 TMDS data 2- 16 Hot-plug detection 2 TMDS data 2+ 17 TMDS data 0- 3 TMDS data 2/4 shield 18 TMDS data 0+ 4 N.C. 19 TMDS data 0/5 shield 5 N.C. 20 N.C. 6 DDC clock 21 N.C. 7 DDC data 22 TMDS clock shield 8 Anal...
Page 62 - Mounting Precautions
62 E • When installing, removing or moving the monitor, ensure that this is carried out by at least 3 people. (PN-R603: at least 2 people.) • Be sure to use a wall-mount bracket designed or designated for mounting the monitor.• This monitor is designed to be installed on a concrete wall or pillar. R...
