Sharp LC-52HD1E - Manual

Supplied accessories Preparation Attaching the speaker unit • Before attaching (or detaching) the speaker unit, unplug the AC cord from the AC INPUT terminal.• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged. Connect the ends of t...

Attaching the stand unit • Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged. CAUTION• Attach the stand in the correct direction.• Be sure to...

Setting the TV Preparation Antenna Connect the antenna cable from your antenna-/cable socket or the (room-/roof) antenna for antenna input terminal on the back of your TV set to receive digitally/terrestrially broadcast stations.An indoor antenna can also be used under good reception conditions. Pas...

Preparation TV (Front view) TV (Rear view) 5 1 2 3 4 6 7 16 17 18 8 9 10 11 12 13 15 19 14 1 EXT 4 terminals* Do not connect S-VIDEO and VIDEO at the same time. 2 USB terminal 3 Headphones 4 COMMON INTERFACE slot ( g 2) ** Remove the cover when inserting the CI Module. 5 ANT IN terminals 6 AUDIO OUT...

Preparation Inserting the batteries Before using the TV for the first time, insert two “AAA” size batteries (supplied). When the batteries become depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries. Open the battery cover. Insert two supplied “A...

Preparation Remote control unit NOTE • The symbols 8 , 9 and 0 indicate that the buttons become available in respective operating mode when using as a universal remote control. 1 4 5 678 9 10 11 12 13 14 151617 1819 20 21 22 2 3 1 B (TV Standby/On) (Page 12) 2 LIGHT D 8 9 0 When pressed, buttons tha...

Initial installation Initial installation overview Follow the below steps one by one when using the TV for the first time. Some steps may not be necessary depending on your TV installation and connection. 9 n Connect the AC cord (Page 5) o Connect antenna (Page 5) Analogue/DVB-C/DVB-T antenna: Plug ...

Initial installation Initial installation wizard When the TV powers on for the first time after purchase, the initial auto installation wizard appears. Follow the menus and make the necessary settings one after another. Proceed Initial installation -> Language NOTE • You can repeat this installat...

Switching on/off Turning on/off the power Press a on the TV. Switch it off by pressing a on the TV. • However, please bear in mind that EPG data (electronic programme guide) will be lost, and programmed timer recordings will not be performed by the TV. Standby mode If the TV set is switched on, you ...

With the favourites lists: You can save and select your favourite stations in 6 favourites lists (e.g. for multiple users). Each favourites list can contain up to 99 stations. After initial installation, 10 stations from the station list are already stored in the first list. Change the favourites li...

Connecting external devices The TV’s integrated Connection wizard helps you connect new external devices and make cable changes. Before actually connecting the external device, run the Connection wizard and register the equipment to be connected. E Before connecting ... Carefully read the operation ...

Connection wizard The integrated Connection wizard shows you which terminal you should connect your equipment to. Connect the equipment according to the diagram and follow the messages one after the other. NOTE • New devices should not be connected until they have been registered in the connection w...

Connecting external devices HDMI connection The HDMI connections (High Definition Multimedia Interface) permit digital video and audio transmission via a connection cable from a player.The digital picture and sound data are transmitted without data compression and therefore lose none of their qualit...

Connecting external devices Audio connection Analogue audio: Connect the analogue audio signal from the PC or the SetTopBox via stereo cable to the AUDIO IN (L/R) jack on the TV set. • The sound is played via the speakers connected to the TV set or a speaker system. Digital audio: • An external digi...

Connecting external devices PC compatibility chart Resolution Horizontal Frequency Vertical Frequency Analogue (D- Sub) Digital (HDMI) VESA Standard VGA 640 g 480 31.5 kHz 60 Hz ✔ ✔ g SVGA 800 g 600 37.9 kHz 60 Hz ✔ ✔ g XGA 1024 g 768 48.4 kHz 60 Hz ✔ ✔ g SXGA 1280 g 1024 64.0 kHz 60 Hz ✔ ✔ g FULL H...

Connecting external devices Connecting HDMI device to TV Controlling HDMI devices using AQUOS LINK What is AQUOS LINK? Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you can interactively operate compatible system devices (AV amplifier, DVD, Blu-ray Disc device) using a ...

Connecting external devices AQUOS LINK setup E AQUOS LINK Auto power on If this is activated, the One Touch Play function is enabled.While the TV is in standby mode, it automatically turns on and plays back the image from the HDMI source. Press MENU and the TV menu screen displays. Press c / d to se...

Connecting external devices Operating an AQUOS LINK device AQUOS LINK allows you to operate the HDMI-connected device with one remote control. NOTE • The AQUOS LINK buttons such as B , REV G , PLAY I , FWD J , STOP H inside the flip cover should not be confused with the buttons used for HDD operatio...

Using AV Link function This TV incorporates four typical AV Link functions for smooth connections between the TV and other audiovisual equipment. One Touch Play While the TV is in standby mode, it automatically turns on and plays back the image from the audiovisual source (e.g. VCR, DVD). TV Standby...

Other features Picture in Picture (PIP) Using the PIP menu Here you can set the PIP type (split screen or small picture) and the position of the small picture. Press PIP to activate the PIP screen. Make sure the picture you want to operate is surrounded in a green frame. Press MENU to display the PI...

Other features Using PhotoViewer This TV is equipped with PhotoViewer, allowing you to view pictures in the standard JPEG format via a USB stick or a memory card in a card reader. In addition you can arrange the pictures into a Slideshow. E Connecting Insert a card reader (with a USB cable) or a USB...

Watching Slide show Starting Slide show Press I to start/resume Slide show. NOTE • If no pictures is selected for Slide show, all the pictures in the memory device are played in Slide show. While Slide show is in progress (or paused), you can: ✔ Press OK to display Photo Overview. ✔ Press F to pause...

Other features EPG (Electronic Programme Guide) EPG stands for Electronic Programme Guide and provides you with on-screen programme details. With this system, as with a printed programme guide, you can learn about the current programme. In addition, programmes can be sorted according to certain topi...

Other features Using EPG menu Press EPG . Press MENU . EPG menu Station selection Data capture on (for DVB + analogue) Items Description Select provider In analogue TV reception, there are possibly different providers who broadcast the EPG data for certain station packages. To get another range of s...

Conditional Access Module (CI Module) In order to receive coded digital stations, a Conditional Access Module (CI Module) and a CA Card must be inserted in the CI slot of your TV set. (Page 6)The CI Module and the CA Card are not supplied accessories. They are usually available from your dealer. Ins...

Watching DVB broadcasts Software update TV base software and DVB software To ensure that your TV set is always up to date, from time to time SHARP will make updated TV base software and DVB software versions available. These updates are broadcast via satellite (only via ASTRA1). • This function is n...

Watching DVB broadcasts Radio mode You can only receive radio stations via DVB.If you do not have DVB radio reception then you can play audio from an external device via the TV set using the audio/AV inputs. Press RADIO to activate the DVB radio mode. 18:00 - 18:10 Nachrichten Radio: Stereo EXT6EXT5...

Info display and index feature We have designed the TV with integrated content-based information text for each item so that you do not have to worry about reading the operation manual each time. In conjunction with the index feature, this makes a convenient control system. Using info text Press INFO...

Sound menu Various sound-related settings can be optimised. Sound TV menu DYNAMIC Treble Bass Loudness Dolby Virtual Speaker Auto volume 0 0 off on off off Balance 0 AV output signal Sound 1+2 Headphone volume 50 Switch on volume 30 Volume adjustment for current station 0 Reset Recording Connections...

Recording menu You can set timer programmed recordings with the integrated HDD Digital Recorder or other connected recording devices. Further information on HDD recording is provided in the chapter “ HDD Digital Recorder operation ”. • The internal HDD DIGITAL Recorder cannot record signals from the...

E Manual You may enter the necessary information for recording manually. Select “Manual” instead of “Via EPG” in step 4 in Via EPG . • The station selection screen displays.• You may be routed to the “Time and date” entry screen if the TV does not recognise the current time. Press a / b / c / d to s...

Connections menu Use this menu when connecting recorders, DVD recorder, etc. There is a wizard which will guide you through the individual steps. TV menu AV setup Sound components Antenna DVB AV-Link Miscellaneous Setup Εxtended functions Picture Connections ✔ Connections menu items Items AV setup C...

Menu operation Setup menu You can search for stations automatically or manually as well as set the menu language, timer functions, child lock, etc. Setup Εxtended functions Picture Sound TV menu AQUOS LINK setup Stations Child lock Timer functions Language Miscellaneous Items AQUOS LINK setup Auto p...

Menu operation E Manual tune Use the manual tune option when receiving TV signals whose TV/Colour standard deviate from the one specified. However, this requires detailed knowledge. E Change stations You can move stations, enter or change station names, and delete stations. The operation is the same...

Menu operation Geometry menu In this menu you can set the geometry values of your connected PC. First connect PC to EXT7 (ANALOG RGB) or to EXT5/6 using HDMI/DVI conversion cable. Recording TV menu Picture horizontal Picture vertical Phase position 0 0 0 Geometry Picture Sound Conn Items Picture hor...

Wide modes You can select the picture size. Selectable picture size varies with the type of signal received. Basically, if you set Auto format to “on” in the Setup menu, the optimum Wide mode is automatically chosen for every broadcast. You can however, change the screen format manually as explained...

Menu operation Using teletext menu While in the teletext mode, press MENU to display the Teletext menu. Newsflash Reveal Recording wizard Setup Teletext menu Items Newsflash Reveal/Conceal Recording wizard Setup Preview pages Sub-title pages Character set HiText Buttons for teletext operation Button...

Important information Hard disk (HDD) This TV set records programmes onto a hard disk drive (HDD). The hard disk is equipped with a safety mechanism to protect data from impact, vibration and dust. However, to prevent loss of recorded data, you should be particularly careful of the following points:...

Features About the Digital Recorder system Your SHARP TV set is equipped with a Digital Recorder that includes a hard disk. You can use this to record and playback picture and sound from TV programmes, like with a VCR or DVD recorder. HDTV programmes can also be recorded and played back. However, th...

About time shift viewing and archive recording/playback HDD Digital Recorder operation 43 Always recording... Storing time shift recording into an archive: You can convert the programme you are currently recording with a time shift into an archive. (Page 46) Archive recording You can choose to store...

HDD Digital Recorder operation Recording with the HDD Time shift recording and archive recording There are 2 ways of recording a TV programme with the HDD. One is Time shift recording and the other is Archive recording. E Time shift recording The TV automatically records the programme currently tune...

Recording Press E . • If time shift is enabled this operation initiates the conversion of time shifted recording into the archive. current programme 30 60 90 120 180 Recording duration (min.) Select “current programme” (only if EPG or teletext data is available) or select one of the given minutes, o...

Timer recording You can programme the timer using the EPG, teletext or manually. You can programme up to 50 timer recordings. If you have programmed timer recordings, the TV set may only be switched off into the stand-by mode. NOTE • Do not switch the TV set off with the main power switch ( a ) and ...

HDD Digital Recorder operation E Deleting programmed timer entries In the TV mode, press MENU to display the TV menu. Select “Recording” with c / d and press b to move down. Select “Timer list” with a / b , and then press OK . Select the entry to delete with a / b . Press YELLOW (Delete), and confir...

HDD Digital Recorder operation E Fast forward and rewind You can fast forward and rewind at 3 different speeds during time shifted TV viewing or archive playback. No sound is audible during winding. (When viewing HDTV, rewind is not possible.) Press Fast Forward J or Rewind G briefly. Press Fast For...

HDD Digital Recorder operation E Copying recordings to an external device This is simple with a VCR or DVD recorder equipped with AV Link. Press RED to display the DR archive menu. Press YELLOW (Delete/copy). 31.08. Das Erste da capo 14.09 Phoenix Bon(n) jour Berlin 29.09. 3sat AVO-Session Basel 06....

HDD Digital Recorder operation Bookmark For example, you want to flag interesting scenes and goals of sports programmes in order to watch them again when playing the recording. You can set bookmarks while you are watching the live picture with time shift, while recording into the archive or playing ...

Appendix Troubleshooting Problem Possible Solution • No power. • Check if you pressed B on the remote control unit. If the indicator on the TV lights up red, press B . • Is the AC cord disconnected?• Check if you pressed a on the TV. • Unit cannot be operated. • External influences such as lightning...

C1 C2 C3 C4 P1 P2 P3 P4 0 0 5 5 1 0 0 – 3 0 0 0 0 9 0 ? ? ? ? ? O K E R R RS-232C port specifications PC Control of the TV • When a programme is set, the TV can be controlled from the PC using the RS-232C terminal. The input signal (PC/video) can be selected, the volume can be adjusted and various o...

CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS POWER SETTING P O W R 0 _ _ _ POWER OFF INPUT SELECTION A I T V D _ _ _ _ TV (CHANNEL FIXED) I A V D * _ _ _ EXT1 – 7 (1 – 7) I A V D ? ? ? ? 1 to 7, 0 (TV/DTV) CHANNEL D C C H * * * _ TV DIRECT CHANNEL (0 – 999) D C C H ? ? ? ? 0 to 999 C H U P _ _ _ ...

Appendix Using the universal remote control You can operate the connected AV products (DVD player/recorder, SetTopBox, VCR and others) by setting up your remote control as a universal remote control unit. NOTE • Some manufacturer code indicated in the operational manual and the universal remote cont...

Appendix Specifications Item 46 o LCD COLOUR TV, Model: LC-46HD1E 52 o LCD COLOUR TV, Model: LC-52HD1E LCD panel 46 o Advanced Super View & BLACK TFT LCD 52 o Advanced Super View & BLACK TFT LCD Number of dots 6,220,800 dots (1920 g 1080 g 3 dots) Video Colour System PAL/SECAM/NTSC 3.58/NTSC...

LC-46HD1ELC-52HD1E LCD COLOUR TELEVISIONLCD-FARBFERNSEHGERÄTTÉLÉVISION COULEUR À ÉCRAN À CRISTAUX LIQUIDES (LCD) TELEVISORE A COLORI LCD ENGLISH DEUTSCH FRANÇAIS SHARP ELECTRÓNICA ESPAÑA S.A. Polígono Industrial Can Sant Joan Calle Sena s/n 08174 SANT CUGAT DEL VALLÉS BARCELONA (ESPAÑA) SHARP CORPOR...