Shark AV2610WA - User Manual

Page 2 - WARNING; IMPORTANT SAFETY INSTRUCTIONS; PLEASE READ CAREFULLY BEFORE USE • FOR HOUSEHOLD USE ONLY; SAVE THESE INSTRUCTIONS; For the latest warnings and cautions, go to

WARNING To reduce the risk of fire, electric shock, injury, or property damage: IMPORTANT SAFETY INSTRUCTIONS PLEASE READ CAREFULLY BEFORE USE • FOR HOUSEHOLD USE ONLY If the charging cable plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified elect...

Page 6 - Sleep Mode; BASE SETUP; INSTALLING THE SIDE BRUSH; permanent; INDICATOR

ROBOT BATTERY INDICATOR LIGHTS BASE INDICATOR LIGHTS NOTE: If the low charge light is blinking red, there is not enough battery power for the robot to return to the base. Manually place the robot on the base. TIP: To preserve battery life, if the robot will not be used for a long time, turn off the ...

Page 8 - BUTTONS AND INDICATOR LIGHTS; against the base, the; to the base so that it; CHARGING

BUTTONS AND INDICATOR LIGHTS When the Vac & Mop 2-in-1 Dust Bin is installed and the robot is properly aligned on the base with the robot’s FRONT against the base, the Charging Symbol on the top right side of the base will illuminate. The robot will beep when charging begins. NOTE: If the robot ...

Page 10 - to; MANUAL CLEANING MODE; To manually start a cleaning cycle, press the

PREP YOUR HOME USING THE SHARK AI ULTRA™ 2-IN-1 ROBOT AI LASER NAVIGATION™ After setup is complete, follow instructions in the app to help your robot conduct an Explore Run to create an initial map of your home. Ensure the Self-Empty Dust Bin is inserted for the Explore Run. The robot will travel fr...

Page 12 - VACUUM-ONLY CLEANING MODES; Single-Room UltraClean

VAC & MOP 2-IN-1 CLEANING MODE VACUUM-ONLY CLEANING MODES Single-Room UltraClean Once the robot has a created map, you can select a specific room to be cleaned in UltraClean mode. Place the robot in the room to be cleaned, then press the CLEAN button. This function is also available through the ...

Page 14 - MUST

USING THE SHARK AI ULTRA™ 2-IN-1 ROBOT USING THE SHARK AI ULTRA™ 2-IN-1 ROBOT VAC & MOP 2-IN-1 SETUP VAC & MOP 2-IN-1 SETUP Secure the pad to the Vac & Mop 2-in 1 Dust Bin. Lift open the fill cap on the top of the reservoir. Fill with water to the WATER line, then add VACMOP™ cleaning so...

Page 16 - Base Dust Bin; MAINTENANCE

MAINTENANCE EMPTYING THE BASE DUST BIN The Base Dust Bin holds up to 60 days' worth of dust and debris. Empty the base dust bin when the debris level approaches the max fill line. To detach the bin, press the Dust Bin Release button on top right side of the base, then slide out the bin. To empty the...

Page 18 - CLEAN POST-MOTOR FILTER EVERY YEAR; CLEANING AND REPLACING THE BASE FILTERS

MAINTENANCE CLEAN POST-MOTOR FILTER EVERY YEAR Press the button at the top of the Filter Door and slide the latch down to lift Filter Door off. Remove the Post-Motor Filter from the base by pulling the tab down. Tap the filters clean over the trash. Do not use water or soap to clean filters as this ...

Page 20 - CLEANING AND REPLACING THE ROBOT'S FILTERS; See sharkclean.com for replacement parts and accessories.

MAINTENANCE MAINTENANCE CLEANING AND REPLACING THE ROBOT'S FILTERS Remove and empty the Self-Empty Dust Bin. Pull filter out of the dust bin by the tabs. Lightly tap the filter to remove debris every time you empty the dust bin. Replace the filter every 6-12 months or as needed. Reinsert the filter ...

Page 22 - The; Self- Cleaning Brushroll; Lift out the brushroll and remove any debris.; CLEANING SENSORS AND CHARGING CONTACTS; CLEAN SENSORS AND CHARGING CONTACTS AS NEEDED.; With a dry cloth, gently dust off the sensors; CLEAN SIDE BRUSH AS NEEDED.; CLEANING THE LIDAR NAVIGATION MODULE

CLEANING THE SELF-CLEANING BRUSHROLL MAINTENANCE The Self- Cleaning Brushroll actively removes hair wrap while your robot cleans. If some debris remains wrapped around the brushroll, continue to run the robot to give the brushroll time to clean itself. If some hair wrap or debris remains after conti...

Page 24 - ERROR CODE; USING THE SHARKCLEAN® APP AND VOICE CONTROLS; WI-FI TROUBLESHOOTING; What should I do if my Wi-Fi randomly disconnects?

USING THE SHARK AI ULTRA™ 2-IN-1 ROBOT WI-FI TROUBLESHOOTING ERROR CODE PROBLEM ! (RED) + Wi-Fi indicator (RED Flashing) Wrong password for Wi-Fi ! (Flashing red) + Wi-Fi (RED) SSID cannot be found, try connecting again ! + Wi-Fi (Flashing RED at the same time) Cannot connect to Wi-Fi USING THE SHAR...

Page 26 - REPLACEMENT PARTS; REPLACEMENT PARTS: ROBOT; ERROR CODES

REPLACEMENT PARTS NOT E: To o rd e r rep lacement p arts a n d f i lte rs , v is it s h a rka cce ss orie s .com . Ro b ot F i l ter Br u sh roll Side Br u sh Cha rg i n g B as e Se l f-Empty Dust Bin Base D u st Bin Br ush rol l Do o r Base P re-Motor Foam & Fe l t F i l te r Kit B a se Post - ...

Page 28 - You hereby acknowledge that SN APPS may contain software that is; END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE; SharkNinja Operating; . DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.

END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE 5.6 You will not use the Ayla Application Libraries or Ayla Embedded Software to attempt to gain unauthorized access to or use of the systems/services of SharkNinja’s other licensors; nor will You transmit viruses, worms, Trojan horses, time bombs, ...

Page 30 - REGISTER YOUR PURCHASE; registeryourshark.com; SharkNinja; What is covered by this warranty?

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE . This Owner's Guide is designed to help you keep your Shark AI Ultra™ 2-In-1 Robot running at peak performance. SharkNinja Operating LLC US: Needham, MA 02494 CAN: Ville St-Laurent, QC H4S 1A71-888-228-5531 sharkclean.comIllustrations may differ f...

Shark AV2610WA - User Manual

Table of Contents:

Summary

Other Shark Models