Page 3 - U Series 9 ce
Page 4 - ©2003– 2004, Seagate Technology LLC All rights reserved
©2003– 2004, Seagate Technology LLC All rights reserved Publication number: 100271705, Rev. F May 2004 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, and SeaTDD are either registered trademarks or trademarks of Seag...
Page 5 - Revision status summary sheet; Revision
Revision status summary sheet Revision Date Sheets Affected Rev. A 01/31/03 All. Rev. B 04/15/03 Page 24. Rev. C 05/07/03 Pages 6, 30-32, and 37-41 Rev. D 07/14/03 Pages 1, 4, 5, 7, 11, 12, and 13. Also new design and page size. Rev. E 12/01/03 Page 16. Rev. F 05/18/04 Page 3 - 5 and 7.
Page 7 - Contents
U Series 9 ce Product Manual, Rev. F v Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 9 - vii; List of Figures
U Series 9 ce Product Manual, Rev. F vii List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 10 - viii
Page 11 - Introduction; U Series 9
U Series 9 ce Product Manual, Rev. F 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® U Series 9 ® ce model drives: • ST3160022ACE• ST3120025ACE• ST380012ACE These drives provide the following key features:• High instantaneo...
Page 13 - Drive specifications; the drive; Specification summary table
U Series 9 ce Product Manual, Rev. F 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST3160022ACE, ST3120025ACE, ...
Page 15 - Formatted capacity; LBA mode; where; Default logical geometry; Interface
U Series 9 ce Product Manual, Rev. F 5 2.2 Formatted capacity 2.2.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above . See Section 4.1.2, "Identify Device command" (w...
Page 16 - Maximum height; Read; Average
6 U Series 9 ce Product Manual, Rev. F 2.6 Physical characteristics 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows:• Track-to-track seek time is an ...
Page 17 - Spinup
U Series 9 ce Product Manual, Rev. F 7 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 7. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup ...
Page 18 - Typical current profile; Typical 5V startup and operation current profile
8 U Series 9 ce Product Manual, Rev. F 2.9.1.1 Typical current profile Figure 1. Typical 5V startup and operation current profile Figure 1. Typical 12V startup and operation current profile 1 2 3 4 5 6 7 8 9 0.0 0.2 0.4 0.6 0.8 1.0 Amps Seconds +5 Volt Current during spindle start — Typical Amperes ...
Page 20 - Environmental specifications
10 U Series 9 ce Product Manual, Rev. F activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disc access is necessary. 2.10 Environmental specifications 2.10.1 Ambient temperature Ambient tem...
Page 21 - Acoustics
U Series 9 ce Product Manual, Rev. F 11 2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels spec...
Page 22 - Electromagnetic immunity; Fluid Dynamic Bearing (FDB) motor acoustics
12 U Series 9 ce Product Manual, Rev. F * During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels . 2.12 Electromagnetic immunity When properly installed in a representative host system, the ...
Page 23 - Agency certification; Safety certification
U Series 9 ce Product Manual, Rev. F 13 2.14 Agency certification 2.14.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.14.2 Electromagnetic compatibility Hard dri...
Page 24 - . This booklet is available from the Super-
14 U Series 9 ce Product Manual, Rev. F Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. This equipment is des...
Page 25 - Configuring and mounting the drive; Handling and static discharge precautions; • Handle the drive by its edges or frame
U Series 9 ce Product Manual, Rev. F 15 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potenti...
Page 26 - Breather filter hole precautions; Breather filter hole location
16 U Series 9 ce Product Manual, Rev. F 3.2 Breather filter hole precautions This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent p...
Page 27 - Jumper settings; Master/slave configuration; only; Alternate capacity jumper
U Series 9 ce Product Manual, Rev. F 17 3.3 Jumper settings 3.3.1 Master/slave configuration The options jumper block shown in Figure 1 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to con...
Page 28 - Ultra ATA cable connectors; Drive mounting
18 U Series 9 ce Product Manual, Rev. F Windows XP, Windows Me, Windows 98 or newer versions are needed to support drives with capacities greater than 32 Gbytes. 3.3.4 Ultra ATA/100 cable An 80-conductor 40-pin cable is required to run Ultra DMA mode 3, mode 4 and mode 5. This cable uses even-number...
Page 29 - Mounting dimensions—top, side and end view; Dimensions per SFF-8301 specification.
U Series 9 ce Product Manual, Rev. F 19 Figure 1. Mounting dimensions—top, side and end view Notes:1. Dimensions are shown in inches (mm). 2 Dimensions per SFF-8301 specification. 3 x 6-32 UNC-2B0.225 (5.72) max. fastenerpenetration both sides. 3 threadsminimum engagement. Recommended case temperatu...
Page 31 - ATA interface; subsequently referred to as the; ATA interface signals and connector pins
U Series 9 ce Product Manual, Rev. F 21 4.0 ATA interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The drive also supports the use of ...
Page 32 - I/O pins and supported ATA signals
22 U Series 9 ce Product Manual, Rev. F Figure 1. I/O pins and supported ATA signals Reset– Ground DD7DD8DD6DD9DD5 DD10 DD4 DD11 DD3 DD12 DD2 DD13 DD1 DD14 DD0 DD15 Ground (removed) DMARQ Ground DIOW– STOP Ground DIOR– HDMARDY– HSTROBE Ground IORDY DDMARDY– DSTROBE CSEL DMACK– Ground INTRQ IOCS16– D...
Page 33 - Supported ATA commands; Command name
U Series 9 ce Product Manual, Rev. F 23 4.1.1 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Draft ATA-6 Standard. See “S.M.A.R.T. commands” on page 29 for details and sub- commands used in ...
Page 35 - Identify Device command; The Identify Device command (command code EC; xxxx
U Series 9 ce Product Manual, Rev. F 25 4.1.2 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 27. All...
Page 36 - Word
26 U Series 9 ce Product Manual, Rev. F 59 Number of sectors transferred during a Read Multiple or Write Multiple command xxxx H 60–61 Total number of user-addressable LBA sectors available(see Section 2.2 for related information)*Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,...
Page 37 - Bit
U Series 9 ce Product Manual, Rev. F 27 Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data: 128 Security status 0001 H 129–159 Seagate-reserved xxxx H 160–25...
Page 38 - Set Features command
28 U Series 9 ce Product Manual, Rev. F 4.1.3 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-rupt. If the val...
Page 41 - Seagate Technology support services; Online Services; Internet; hours daily by e-mail for your questions.; mySeagate; Automated Phone Services; SeaFONE; Presales, Technical Support and Warranty Service; Presales Support; SeaTDD; is a
U Series 9 ce Product Manual, Rev. F 31 5.0 Seagate Technology support services Online Services Internet www.seagate.com for information about Seagate products and services. Worldwide support is available 24 hours daily by e-mail for your questions. Presales Support: www.seagate.com/support/email/em...
Page 43 - USA/Canada/Latin America Support Services; Technical Support; Americas; Warranty Service; Memofix; Hours of operation are 8:00
U Series 9 ce Product Manual, Rev. F 33 USA/Canada/Latin America Support Services Presales Support Call Center Toll-free Direct dial FAX Americas 1-877-271-3285 1 +1-405-324-4730 1 +1-405-324-4704 Technical Support Call Center Toll-free Direct dial FAX Americas 1-800-SEAGATE 2 +1-405-324-4700 3 +1-4...
Page 44 - European Support Services; Toll-Free Support Numbers; Call Center; Africa/Middle East Support Services
34 U Series 9 ce Product Manual, Rev. F European Support Services For presales and technical support in Europe, dial the toll-free number for your specific location. If your location is not listed here, dial our presales and technical support call center at +1-405-324-4714 from 8:00 A . M . to 11:45...
Page 45 - Asia/Pacific Support Services; Hours of operation are 8:30
U Series 9 ce Product Manual, Rev. F 35 Asia/Pacific Support Services For Asia/Pacific presales and technical support, dial the toll-free number for your specific location. The Asia/Pacific toll-free numbers are available from 6:00 A . M . to 10:45 A . M . and 12:00 P . M . to 6:00 P . M . (Australi...
Page 47 - Index; Numerics
U Series 9 ce Product Manual, Rev. F 37 Index Numerics 3D Defense System 1 A acoustics 11 Active mode 9 agency certification (regulatory) 13 alternate capacity jumper 17 altitude 10 ambient conditions 3 ambient temperature 6 , 10 areal density 1 , 5 ATA interface 21 ATA-standard commands 23 Australi...
Page 52 - Seagate Technology LLC
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100271705, Rev. F, Printed in USA
