SEAGATE U Series 9 CE - Manuals

U Series 9 ce Product Manual, Rev. F v Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

U Series 9 ce Product Manual, Rev. F vii List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . ...

U Series 9 ce Product Manual, Rev. F 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® U Series 9 ® ce model drives: • ST3160022ACE• ST3120025ACE• ST380012ACE These drives provide the following key features:• High instantaneo...

U Series 9 ce Product Manual, Rev. F 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST3160022ACE, ST3120025ACE, ...

U Series 9 ce Product Manual, Rev. F 5 2.2 Formatted capacity 2.2.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above . See Section 4.1.2, "Identify Device command" (w...

6 U Series 9 ce Product Manual, Rev. F 2.6 Physical characteristics 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows:• Track-to-track seek time is an ...

U Series 9 ce Product Manual, Rev. F 7 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 7. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup ...

8 U Series 9 ce Product Manual, Rev. F 2.9.1.1 Typical current profile Figure 1. Typical 5V startup and operation current profile Figure 1. Typical 12V startup and operation current profile 1 2 3 4 5 6 7 8 9 0.0 0.2 0.4 0.6 0.8 1.0 Amps Seconds +5 Volt Current during spindle start — Typical Amperes ...

10 U Series 9 ce Product Manual, Rev. F activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disc access is necessary. 2.10 Environmental specifications 2.10.1 Ambient temperature Ambient tem...

U Series 9 ce Product Manual, Rev. F 11 2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels spec...

12 U Series 9 ce Product Manual, Rev. F * During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels . 2.12 Electromagnetic immunity When properly installed in a representative host system, the ...

U Series 9 ce Product Manual, Rev. F 13 2.14 Agency certification 2.14.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.14.2 Electromagnetic compatibility Hard dri...

14 U Series 9 ce Product Manual, Rev. F Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. This equipment is des...

U Series 9 ce Product Manual, Rev. F 15 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potenti...

16 U Series 9 ce Product Manual, Rev. F 3.2 Breather filter hole precautions This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent p...

U Series 9 ce Product Manual, Rev. F 17 3.3 Jumper settings 3.3.1 Master/slave configuration The options jumper block shown in Figure 1 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to con...

18 U Series 9 ce Product Manual, Rev. F Windows XP, Windows Me, Windows 98 or newer versions are needed to support drives with capacities greater than 32 Gbytes. 3.3.4 Ultra ATA/100 cable An 80-conductor 40-pin cable is required to run Ultra DMA mode 3, mode 4 and mode 5. This cable uses even-number...

U Series 9 ce Product Manual, Rev. F 19 Figure 1. Mounting dimensions—top, side and end view Notes:1. Dimensions are shown in inches (mm). 2 Dimensions per SFF-8301 specification. 3 x 6-32 UNC-2B0.225 (5.72) max. fastenerpenetration both sides. 3 threadsminimum engagement. Recommended case temperatu...

U Series 9 ce Product Manual, Rev. F 21 4.0 ATA interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The drive also supports the use of ...

22 U Series 9 ce Product Manual, Rev. F Figure 1. I/O pins and supported ATA signals Reset– Ground DD7DD8DD6DD9DD5 DD10 DD4 DD11 DD3 DD12 DD2 DD13 DD1 DD14 DD0 DD15 Ground (removed) DMARQ Ground DIOW– STOP Ground DIOR– HDMARDY– HSTROBE Ground IORDY DDMARDY– DSTROBE CSEL DMACK– Ground INTRQ IOCS16– D...

U Series 9 ce Product Manual, Rev. F 23 4.1.1 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Draft ATA-6 Standard. See “S.M.A.R.T. commands” on page 29 for details and sub- commands used in ...

U Series 9 ce Product Manual, Rev. F 25 4.1.2 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 27. All...

26 U Series 9 ce Product Manual, Rev. F 59 Number of sectors transferred during a Read Multiple or Write Multiple command xxxx H 60–61 Total number of user-addressable LBA sectors available(see Section 2.2 for related information)*Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,...

U Series 9 ce Product Manual, Rev. F 27 Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data: 128 Security status 0001 H 129–159 Seagate-reserved xxxx H 160–25...

28 U Series 9 ce Product Manual, Rev. F 4.1.3 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-rupt. If the val...

U Series 9 ce Product Manual, Rev. F 31 5.0 Seagate Technology support services Online Services Internet www.seagate.com for information about Seagate products and services. Worldwide support is available 24 hours daily by e-mail for your questions. Presales Support: www.seagate.com/support/email/em...

U Series 9 ce Product Manual, Rev. F 33 USA/Canada/Latin America Support Services Presales Support Call Center Toll-free Direct dial FAX Americas 1-877-271-3285 1 +1-405-324-4730 1 +1-405-324-4704 Technical Support Call Center Toll-free Direct dial FAX Americas 1-800-SEAGATE 2 +1-405-324-4700 3 +1-4...

34 U Series 9 ce Product Manual, Rev. F European Support Services For presales and technical support in Europe, dial the toll-free number for your specific location. If your location is not listed here, dial our presales and technical support call center at +1-405-324-4714 from 8:00 A . M . to 11:45...

U Series 9 ce Product Manual, Rev. F 35 Asia/Pacific Support Services For Asia/Pacific presales and technical support, dial the toll-free number for your specific location. The Asia/Pacific toll-free numbers are available from 6:00 A . M . to 10:45 A . M . and 12:00 P . M . to 6:00 P . M . (Australi...

U Series 9 ce Product Manual, Rev. F 37 Index Numerics 3D Defense System 1 A acoustics 11 Active mode 9 agency certification (regulatory) 13 alternate capacity jumper 17 altitude 10 ambient conditions 3 ambient temperature 6 , 10 areal density 1 , 5 ATA interface 21 ATA-standard commands 23 Australi...

Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100271705, Rev. F, Printed in USA