Page 2 - Contents; Seagate; SeaBOARD
Contents Introduction ........................................................... 1Electromagnetic interference ................................ 1Before you begin .................................................. 3Installation overview ............................................. 8Product Repair ....
Page 3 - Hawk 1LP Family Installation Guide, Rev. D 1; Introduction
Hawk 1LP Family Installation Guide, Rev. D 1 Introduction This manual is organized to assist you in the installa-tion and operation of your Seagate Hawk 1LP Familydisc drive. Family models are listed in Hawk 1LP FamilyProduct Information section. It also provides informa-tion to aid in obtaining ser...
Page 4 - Hawk 1LP Family Installation Guide, Rev. D
2 Hawk 1LP Family Installation Guide, Rev. D and Regulations nor the Radio Interference Regula-tions of the Canadian Department of Communications.However, the unit has been tested using proper shield-ing and grounding and found to be compliant with theClass A limits of the FCC Rules and the Regulati...
Page 5 - Hawk 1LP Family Installation Guide, Rev. D 3; Before you begin; • Do not tamper with sealed top cover. Doing so voids
Hawk 1LP Family Installation Guide, Rev. D 3 Before you begin Verify that the system is switched off and discon-nected from main power before any installation isattempted. Protect yourself, the drive, and your valuable pro-grams and data by reading the following cautionsand warnings. • Do not tamper...
Page 6 - Caution. The circuit assemblies and components
4 Hawk 1LP Family Installation Guide, Rev. D • When transporting or shipping a drive or system, please ensure that they are correctly packed inoriginal Seagate approved (or equivalent) containerand shipped via an air-ride carrier experienced inhandling computer equipment. • Do not unpack drive from ...
Page 7 - Hawk 1LP Family Installation Guide, Rev. D 5
Hawk 1LP Family Installation Guide, Rev. D 5 Static electrical charges can accumulatequickly on personnel, clothing and syntheticmaterials. The electrostatic fields due tothese charges when brought in close prox-imity to susceptible circuit assemblies andcomponents, can result in degraded reliabil-i...
Page 8 - Hawk 1LP Family Installation Guide, Rev. D; Safety instructions; Power must be off when connecting or disconnecting.
6 Hawk 1LP Family Installation Guide, Rev. D Safety instructions 1. The disc drive(s) are to be installed in a customersupplied enclosure where the surrounding air doesnot exceed 50 o C. 2. Four (4) 6-32 UNC-2A screws are required forinstallation. Maximum screw length into side ofdrive is 0.15 inche...
Page 9 - Hawk 1LP Family Installation Guide, Rev. D 7; Sicherheitsanleitung
Hawk 1LP Family Installation Guide, Rev. D 7 Sicherheitsanleitung 1. Däs Gerät ist ein Einbaugerät, vorgesehen für einemaximale Umgebungstemperatur von 50 o C. 2. Zur Befestigung der Drive werden 4 Schraubenbenötigt (6-32 UNC-2A). Die maximale Länge derSchrauben in der unteren Seite des Chassis darf...
Page 10 - Hawk 1LP Family Installation Guide, Rev. D; Installation Overview; • Drive configuration: Select those drive features
8 Hawk 1LP Family Installation Guide, Rev. D Installation Overview Installation of the drive can be divided into distinctphases. Some of these may not be applicable to allsystem installation requirements. Refer to the indi-vidual drive installation sections for specific informationon your drive mode...
Page 11 - Hawk 1LP Family Installation Guide, Rev. D 9; • Low-Level formatting: All Hawk 1LP family drive
Hawk 1LP Family Installation Guide, Rev. D 9 • Low-Level formatting: All Hawk 1LP family drive models are low-level formatted at the factory and donot require this step during installation. If an installeddrive is low-level formatted, all user data will be lost. Note: Seagate Technology assumes no l...
Page 12 - 0 Hawk 1LP Family Installation Guide, Rev. D; Product repair information; Service requirements
10 Hawk 1LP Family Installation Guide, Rev. D Product repair information Service requirements The special facilities required for the manufacture ofthese drives generally prohibit repair in the field. Ifproblems occur during installation, please contact yoursupplier for assistance. Do not attempt to...
Page 13 - Product repair and return information
Hawk 1LP Family Installation Guide, Rev. D 11 • Place drive on a flat, static dissipative surface and handle with extreme care. Always follow all EOS/ESD precautions to avoid damage to the electricalassemblies. Shipping: When transporting or shipping a drive, aSeagate approved container must be used...
Page 14 - 2 Hawk 1LP Family Installation Guide, Rev. D; Technical support services
12 Hawk 1LP Family Installation Guide, Rev. D Warranty: Contact your Seagate Authorized Distribu-tor, Dealer or other purchase source for warrantyinformation. If the drive is no longer under warranty contact pur-chase source for repair information or refer to numberslisted in section Technical Suppo...
Page 15 - Hawk 1LP Family Installation Guide, Rev. D 13
Hawk 1LP Family Installation Guide, Rev. D 13 SeaFONE telephone number: 408/438-8222 The enhanced phone system provides recorded tech-nical information on selected Seagate products whileyou are on hold. Technical support specialists areavailable to answer questions from 8:00 AM to 5:00PMPST, Monday ...
Page 17 - Hawk 1LP Family Installation Guide, Rev. D 15; Hawk 1LP Family product information; Legend for table column meanings:; Model
Hawk 1LP Family Installation Guide, Rev. D 15 Hawk 1LP Family product information Characteristics of the various drives covered by thismanual are listed in the following table. Legend for table column meanings: A = capacity, unformatted megabytes B = capacity, formatted megabytes [1] C = number of c...
Page 19 - Hawk 1LP Family Installation Guide, Rev. D 17; Initial set-up information; SCSI interface cable connection
Hawk 1LP Family Installation Guide, Rev. D 17 Initial set-up information For the initial setup connect the cables or plug into amounted connector (if applicable), set the drive ID onthe bus and enable or disable the I/O line terminatorresistor packs ("N" and some "NC" models). Thesep...
Page 20 - 8 Hawk 1LP Family Installation Guide, Rev. D; DC Power connection; connector; SCSI address selection
18 Hawk 1LP Family Installation Guide, Rev. D DC Power connection "N" and "ND" model family drives receive DC powerthrough a 4 pin connector mounted on the PCB next tothe SCSI I/O connector. See figure below. Figure 1. DC power connection, 50 pin SCSI I/O connector "NC" model...
Page 21 - Hawk 1LP Family Installation Guide, Rev. D 19; Terminator resistor packs
Hawk 1LP Family Installation Guide, Rev. D 19 order. Bus addresses 0 through 6 should be used (thehost adapter usually uses address 7). If the drive LEDshows no on/off activity when the host is trying tocommunicate with it, an incorrect bus address selec-tion at the drive should be suspected. On ...
Page 22 - 0 Hawk 1LP Family Installation Guide, Rev. D; Optional parity bit enable
20 Hawk 1LP Family Installation Guide, Rev. D Model numbers that end in "ND" have differential I/Ocircuits and these drives and some "NC" model driveshave no provisions for terminators on the drive PCB.The system manufacturer must provide some externalmeans of I/O line termination. T...
Page 23 - Hawk 1LP Family Installation Guide, Rev. D 21; Figure 2a. Hawk 1LP family N/ND model drives
80 Pin SCSI I/O and Power Connector J4 J6 J2 Pin 1 U5 Terminator Module Pin 1 50 Pin SCSI I/O Connector J6 J5 J2 Hawk 1LP Family Installation Guide, Rev. D 21 Figure 2a. Hawk 1LP family N/ND model drives I/O connection (50 pin SCSI I/O connector)."N" model drive terminators (not visible)are ...
Page 24 - 2 Hawk 1LP Family Installation Guide, Rev. D; Drive configuration
22 Hawk 1LP Family Installation Guide, Rev. D Drive configuration Each disc drive has one or more option select headerconnectors on the back, side or front where jumperplugs are installed to select the way that the drive is tobe configured or to select its ID on the I/O bus. Seenotes following Figur...
Page 25 - Hawk 1LP Family Installation Guide, Rev. D 23
Hawk 1LP Family Installation Guide, Rev. D 23 Hawk 1LP family NC models (80 pin SCSI I/O) On Model NC drives there is no J5. J6 can be used toset drive ID, but the host probably does it over the 80 pininterface. J6 is used to select other configuration op-tions as has previously been described, or i...
Page 26 - 4 Hawk 1LP Family Installation Guide, Rev. D; Figure 3a. Drive configurator, Hawk 1LP family
Pin 1 End Pin 1 SCSI I/O Connector Pin 1 J2 See Figure 3b Drive with HDA up,PCB down, viewed from front A 2 A 1 A 0 SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 Sync Spindle Remote LED Delay Motor Start Enable Motor Start Write Protect Parity Option...
Page 27 - Hawk 1LP Family Installation Guide, Rev. D 25; Figure 3b. Drive configurator, Hawk 1LP family
Pin 1 SCSI I/O Connector Pin 1 HDA Side View of Drive J1 SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 J5 A 0 A1 A2 DC PowerConnector J2 Drive Front J6 J5 J1 50 pin SCSI connector [2] Hawk 1LP Family Installation Guide, Rev. D 25 Figure 3b. Drive con...
Page 28 - 6 Hawk 1LP Family Installation Guide, Rev. D; Figure 3c. Drive configurator for Hawk 1LP family
J2 Drive Front Pin 1 End J6 80 PinSCSI I/O Connector Pin 1 J2 Pin 1 HDA Drive with HDA up, PCB down, viewed from front J6 A 2 A 1 A 0 SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 Sync Spindle Remote LED Delay Motor Start Enable Motor Start Write Pro...
Page 30 - 8 Hawk 1LP Family Installation Guide, Rev. D; Jumper Function Description
28 Hawk 1LP Family Installation Guide, Rev. D J2JumperPosition Jumper Function Description RESOff/On Reserved. Default is no jumper installed. DS MEOff Off Spindle starts immediately after power up - De-fault setting. Off On Drive spindle does not start until Start Unit com-mand received from host. ...
Page 31 - Hawk 1LP Family Installation Guide, Rev. D 29; TP TP
Hawk 1LP Family Installation Guide, Rev. D 29 continued from previous page PEOn Parity checking and parity error reporting by thedrive is enabled. Off Drive does not report result of parity checking tohost. Default is no PE jumper installed. TE (Applies to "N" and some "NC" models on...
Page 32 - 0 Hawk 1LP Family Installation Guide, Rev. D; continued from previous page; See above explanations for TP jumpers.; position A
30 Hawk 1LP Family Installation Guide, Rev. D continued from previous page TP Position A ("N" family models only)On This horizontally positioned jumper across thetwo TP positions nearest PCB edge, connectsterminator power from SCSI bus I/O pin 26 to thedrive's internal terminators. Off See a...
Page 33 - Hawk 1LP Family Installation Guide, Rev. D 31; RES; Reserved position. No jumper to be installed.
Hawk 1LP Family Installation Guide, Rev. D 31 continued from previous page SSP* Used only as a cable connection for the refer-ence index signal (REFIND+) (J6 Pin 6, bot-tom) for sync spindle feature. J6 pin 5 is GRD.Install a jumper when no cable is attached.Default is a jumper installed (not applic...
Page 34 - 2 Hawk 1LP Family Installation Guide, Rev. D; Drive installation; Disc drive mounting; The drive may be mounted in any orientation.
32 Hawk 1LP Family Installation Guide, Rev. D Drive installation This section describes the physical mounting of thedrive in the host cabinet and the logical installation asa system member, which is called drive setup. Disc drive mounting Do not touch the connector pins or any PCB compo-nents withou...
Page 36 - 4 Hawk 1LP Family Installation Guide, Rev. D; Figure 4. Hawk 1LP family N/ND model mounting
A F D E C [1] [3] B G [1] Mounting holes three on each side, 6-32 UNC. Max screw length into side of drive 0.15 in. (3.81 mm). Maximum torque 8 in-lb (.90 NM). Min. thread engagement 0.12 in. (3.0 mm). [2] Mounting holes four on bottom, 6-32 UNC. Max screw length into bottom of drive 0.20 in. (5.08 ...
Page 37 - Hawk 1LP Family Installation Guide, Rev. D 35; Figure 5. Hawk 1LP family NC model mounting
A F D E L [1] [3] B G [1] Mounting holes three on each side, 6-32 UNC. Max screw length into side of drive 0.15 in. (3.81 mm). Maximum torque 8 in-lb (.90 NM). Min. thread engagement 0.12 in. (3.0 mm). [2] Mounting holes four on bottom, 6-32 UNC. Max screw length into bottom of drive 0.20 in. (5.08 ...
Page 38 - Grounding
36 Hawk 1LP Family Installation Guide, Rev. D Do not power up the host system until the drive ismounted and the system cover is replaced. • Connect DC power connector to the drive.• Replace the Host System cover.• Turn on DC power.• Boot the system from the floppy drive or from a previously installe...
Page 39 - Hawk 1LP Family Installation Guide, Rev. D 37; SCSI interface drives
Hawk 1LP Family Installation Guide, Rev. D 37 SCSI interface drives The SCSI interface handles both drive geometry anddefect management internally. The "no drive installed"option is selected for systems with SCSI drives. All SCSI interface drives are low-level formatted at thefactory. You ma...
