SEAGATE ST31200N/ND/NC - Manuals

Hawk 1LP Family Installation Guide, Rev. D 3 Before you begin Verify that the system is switched off and discon-nected from main power before any installation isattempted. Protect yourself, the drive, and your valuable pro-grams and data by reading the following cautionsand warnings. • Do not tamper...

4 Hawk 1LP Family Installation Guide, Rev. D • When transporting or shipping a drive or system, please ensure that they are correctly packed inoriginal Seagate approved (or equivalent) containerand shipped via an air-ride carrier experienced inhandling computer equipment. • Do not unpack drive from ...

Hawk 1LP Family Installation Guide, Rev. D 5 Static electrical charges can accumulatequickly on personnel, clothing and syntheticmaterials. The electrostatic fields due tothese charges when brought in close prox-imity to susceptible circuit assemblies andcomponents, can result in degraded reliabil-i...

6 Hawk 1LP Family Installation Guide, Rev. D Safety instructions 1. The disc drive(s) are to be installed in a customersupplied enclosure where the surrounding air doesnot exceed 50 o C. 2. Four (4) 6-32 UNC-2A screws are required forinstallation. Maximum screw length into side ofdrive is 0.15 inche...

Hawk 1LP Family Installation Guide, Rev. D 7 Sicherheitsanleitung 1. Däs Gerät ist ein Einbaugerät, vorgesehen für einemaximale Umgebungstemperatur von 50 o C. 2. Zur Befestigung der Drive werden 4 Schraubenbenötigt (6-32 UNC-2A). Die maximale Länge derSchrauben in der unteren Seite des Chassis darf...

8 Hawk 1LP Family Installation Guide, Rev. D Installation Overview Installation of the drive can be divided into distinctphases. Some of these may not be applicable to allsystem installation requirements. Refer to the indi-vidual drive installation sections for specific informationon your drive mode...

Hawk 1LP Family Installation Guide, Rev. D 9 • Low-Level formatting: All Hawk 1LP family drive models are low-level formatted at the factory and donot require this step during installation. If an installeddrive is low-level formatted, all user data will be lost. Note: Seagate Technology assumes no l...

10 Hawk 1LP Family Installation Guide, Rev. D Product repair information Service requirements The special facilities required for the manufacture ofthese drives generally prohibit repair in the field. Ifproblems occur during installation, please contact yoursupplier for assistance. Do not attempt to...

Hawk 1LP Family Installation Guide, Rev. D 11 • Place drive on a flat, static dissipative surface and handle with extreme care. Always follow all EOS/ESD precautions to avoid damage to the electricalassemblies. Shipping: When transporting or shipping a drive, aSeagate approved container must be used...

12 Hawk 1LP Family Installation Guide, Rev. D Warranty: Contact your Seagate Authorized Distribu-tor, Dealer or other purchase source for warrantyinformation. If the drive is no longer under warranty contact pur-chase source for repair information or refer to numberslisted in section Technical Suppo...

Hawk 1LP Family Installation Guide, Rev. D 13 SeaFONE telephone number: 408/438-8222 The enhanced phone system provides recorded tech-nical information on selected Seagate products whileyou are on hold. Technical support specialists areavailable to answer questions from 8:00 AM to 5:00PMPST, Monday ...

Hawk 1LP Family Installation Guide, Rev. D 15 Hawk 1LP Family product information Characteristics of the various drives covered by thismanual are listed in the following table. Legend for table column meanings: A = capacity, unformatted megabytes B = capacity, formatted megabytes [1] C = number of c...

Hawk 1LP Family Installation Guide, Rev. D 17 Initial set-up information For the initial setup connect the cables or plug into amounted connector (if applicable), set the drive ID onthe bus and enable or disable the I/O line terminatorresistor packs ("N" and some "NC" models). Thesep...

18 Hawk 1LP Family Installation Guide, Rev. D DC Power connection "N" and "ND" model family drives receive DC powerthrough a 4 pin connector mounted on the PCB next tothe SCSI I/O connector. See figure below. Figure 1. DC power connection, 50 pin SCSI I/O connector "NC" model...

Hawk 1LP Family Installation Guide, Rev. D 19 order. Bus addresses 0 through 6 should be used (thehost adapter usually uses address 7). If the drive LEDshows no on/off activity when the host is trying tocommunicate with it, an incorrect bus address selec-tion at the drive should be suspected. On ...

20 Hawk 1LP Family Installation Guide, Rev. D Model numbers that end in "ND" have differential I/Ocircuits and these drives and some "NC" model driveshave no provisions for terminators on the drive PCB.The system manufacturer must provide some externalmeans of I/O line termination. T...

80 Pin SCSI I/O and Power Connector J4 J6 J2 Pin 1 U5 Terminator Module Pin 1 50 Pin SCSI I/O Connector J6 J5 J2 Hawk 1LP Family Installation Guide, Rev. D 21 Figure 2a. Hawk 1LP family N/ND model drives I/O connection (50 pin SCSI I/O connector)."N" model drive terminators (not visible)are ...

22 Hawk 1LP Family Installation Guide, Rev. D Drive configuration Each disc drive has one or more option select headerconnectors on the back, side or front where jumperplugs are installed to select the way that the drive is tobe configured or to select its ID on the I/O bus. Seenotes following Figur...

Hawk 1LP Family Installation Guide, Rev. D 23 Hawk 1LP family NC models (80 pin SCSI I/O) On Model NC drives there is no J5. J6 can be used toset drive ID, but the host probably does it over the 80 pininterface. J6 is used to select other configuration op-tions as has previously been described, or i...

Pin 1 End Pin 1 SCSI I/O Connector Pin 1 J2 See Figure 3b Drive with HDA up,PCB down, viewed from front A 2 A 1 A 0 SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 Sync Spindle Remote LED Delay Motor Start Enable Motor Start Write Protect Parity Option...

Pin 1 SCSI I/O Connector Pin 1 HDA Side View of Drive J1 SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 J5 A 0 A1 A2 DC PowerConnector J2 Drive Front J6 J5 J1 50 pin SCSI connector [2] Hawk 1LP Family Installation Guide, Rev. D 25 Figure 3b. Drive con...

J2 Drive Front Pin 1 End J6 80 PinSCSI I/O Connector Pin 1 J2 Pin 1 HDA Drive with HDA up, PCB down, viewed from front J6 A 2 A 1 A 0 SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 Sync Spindle Remote LED Delay Motor Start Enable Motor Start Write Pro...

28 Hawk 1LP Family Installation Guide, Rev. D J2JumperPosition Jumper Function Description RESOff/On Reserved. Default is no jumper installed. DS MEOff Off Spindle starts immediately after power up - De-fault setting. Off On Drive spindle does not start until Start Unit com-mand received from host. ...

Hawk 1LP Family Installation Guide, Rev. D 29 continued from previous page PEOn Parity checking and parity error reporting by thedrive is enabled. Off Drive does not report result of parity checking tohost. Default is no PE jumper installed. TE (Applies to "N" and some "NC" models on...

30 Hawk 1LP Family Installation Guide, Rev. D continued from previous page TP Position A ("N" family models only)On This horizontally positioned jumper across thetwo TP positions nearest PCB edge, connectsterminator power from SCSI bus I/O pin 26 to thedrive's internal terminators. Off See a...

Hawk 1LP Family Installation Guide, Rev. D 31 continued from previous page SSP* Used only as a cable connection for the refer-ence index signal (REFIND+) (J6 Pin 6, bot-tom) for sync spindle feature. J6 pin 5 is GRD.Install a jumper when no cable is attached.Default is a jumper installed (not applic...

32 Hawk 1LP Family Installation Guide, Rev. D Drive installation This section describes the physical mounting of thedrive in the host cabinet and the logical installation asa system member, which is called drive setup. Disc drive mounting Do not touch the connector pins or any PCB compo-nents withou...

A F D E C [1] [3] B G [1] Mounting holes three on each side, 6-32 UNC. Max screw length into side of drive 0.15 in. (3.81 mm). Maximum torque 8 in-lb (.90 NM). Min. thread engagement 0.12 in. (3.0 mm). [2] Mounting holes four on bottom, 6-32 UNC. Max screw length into bottom of drive 0.20 in. (5.08 ...

A F D E L [1] [3] B G [1] Mounting holes three on each side, 6-32 UNC. Max screw length into side of drive 0.15 in. (3.81 mm). Maximum torque 8 in-lb (.90 NM). Min. thread engagement 0.12 in. (3.0 mm). [2] Mounting holes four on bottom, 6-32 UNC. Max screw length into bottom of drive 0.20 in. (5.08 ...

36 Hawk 1LP Family Installation Guide, Rev. D Do not power up the host system until the drive ismounted and the system cover is replaced. • Connect DC power connector to the drive.• Replace the Host System cover.• Turn on DC power.• Boot the system from the floppy drive or from a previously installe...

Hawk 1LP Family Installation Guide, Rev. D 37 SCSI interface drives The SCSI interface handles both drive geometry anddefect management internally. The "no drive installed"option is selected for systems with SCSI drives. All SCSI interface drives are low-level formatted at thefactory. You ma...