Sanus VMAA26 - Manual
Sanus VMAA26 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Supplied Television Mounting Hardware:
- Page 3 – Step 1: Mounting Monitor Brackets to a Televisions with a flat back; Determine the diameter of the Bolt (; M4 Diameter Bolt
- Page 4 – DD; ), and finally into the TV. Make sure the Monitor Brackets are
- Page 5 – Step 3: Add the Vise Assemblies to the Monitor Brackets:; Place the Vise Assembly (; Step 4: Attach the Arm Assembly to the Television; Align each Vise Assembly (; Jaws
- Page 6 – Step 4: Attach the Arm Assembly to the Television (Continued); so the flat surface in the center of the plate is against the; Stud
- Page 7 – Step 7: Leveling the Monitor and Adjusting the Tension; Once the television is mounted onto the Wall Plate (; Safety Bracket Installation; Step 6: Hang the assembly onto the Wall Plate; Orient the Arm Assembly (; Transfer Plate
- Page 8 – Idler
Assembly Instructions for Model: VMAA26
Thank you for choosing a Sanus Systems VisionMount™ wall mount. The VMAA26 is designed to mount up to 50” Flat panel televisions
weighing up to 130 lb. to a vertical wall. It allows you to tilt the television from +5° to -15°. It will also extend 25.75” away from the wall,
swivel up to 180°, and roll ± 6°.
CAUTION:
The size and weight of your television must not exceed 50” [1270 mm] diagonally and 130 Lbs [59 Kg]. The wall
must be capable of supporting five times the weight of the television plus the wall mount. Never use defective parts. Improper
installation may cause property damage or personal injury. Do not use this product for any purpose that is not explicitly
specified by Sanus Systems
.
If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor
or contact Sanus at 800.359.5520 or www.sanus.com. Our customer service representatives can quickly assist you with installation
questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly
to you. Check carefully to make sure that there are no missing or defective parts. Sanus Systems can not be liable for damage or injury
caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of
purchase.
NOTE: This mount is not intended for use on brick, concrete block, concrete, or steel wall studs. Typical wall anchors do not
have sufficient holding power to support this mount. It is up to the installer to verify the safety of any installation method or
hardware that is not provided by or recommended by Sanus Systems. Sanus Systems makes every effort to assure all necessary
television mounting hardware is included. If the television mounting hardware you need is not included please consult your
local hardware store or call Sanus Systems
Required Tools:
3/16” drill bit, drill, adjustable or crescent wrench, Phillips screwdriver.
Supplied Parts:
(Some parts are not shown at same scale)
Wall Plate - A
Qty. 1
I” Diameter Tube - D
Qty. 2
Preventor - C
Qty. 1
Arm Assembly - B
Qty. 1
Vise Assembly - F
Qty. 4
Monitor Bracket - E
Qty. 2
Sanus Systems
2221 Hwy 36 West, Saint Paul, MN 55113 09.26.06 (6901-100017)
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Hardware: (Hardware shown is actual size) Wire Tie Clip - G Qty. 7 Wire Tie - H Qty. 10 7/32 & 3/16 Allen Keys - K Qty. 1 Each Lag Bolt Washer - J Qty. 4 Lag Bolt - I Qty. 4 Safety Bolt - N Qty. 3 Preventor Bolt - O Qty. 2 1/4-20 Nut - M Qty. 4 2” Carriage Bolt - L Qty. 4 Supplied Television Mou...
Step 1: Mounting Monitor Brackets to a Televisions with a flat back NOTE: For TVs with a curved back or any other obstruction See Step 2. After completing this step, proceed to Step 3. Determine the diameter of the Bolt ( P,Q,R,S ) your TV requires by hand threading them into the threaded insert on ...
Step 2: Mounting the Monitor Brackets to Televisions with a curved back or other obstruction. Determine the diameter of the Bolt ( T,U,V,W ) your TV requires, by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately. Once you have determ...
