Page 2 - IMPORTANT SAFETY NOTICE; WARNING; choose the right part name.
IMPORTANT SAFETY NOTICE Following the repair by a non-authorized service provider self-repair or non-professional repair of the product Samsung is not liable for any damage to the product any injury or any other product safety issue caused by any attempt to repair the product which does not carefull...
Page 3 - Disassembly and Reassembly _ 3; TOOLS FOR REMOVAL AND REASSEMBLY; Tool image; Adjustable Wrench; Preparation for parts replacement; You must turn off the circuit breaker connected to the product.
Disassembly and Reassembly _ 3 1. TOOLS FOR REMOVAL AND REASSEMBLY Tool image No. Tool Type Remarks ① Adjustable Wrench ② Open-end Wrench 1-7/16” ③ Vice Pliers ④ Others(screwdriver, nipper, long nose pliers) Common tools for servicingScrewdriver – Phillip, Flat, Torx T15 ⑤ Ear clamping tool In reass...
Page 4 - _ Disassembly and Reassembly; STANDARD DISASSEMBLY DRAWINGS; Caution; → There is a risk of water spill on the floor.
4 _ Disassembly and Reassembly 2. STANDARD DISASSEMBLY DRAWINGS 2-1. PRECAUTION Caution Before servicing,- Make sure to remove all items include baskets inside dishwasher.- Drain the water in the dishwasher and disconnect the power supply.- Lock the water faucet that connected with inlet hose.- Unin...
Page 5 - Disassembly and Reassembly _ 5; Remove 3 screws that connect left SIDE PANEL to; Warning; Be sure to remove the power plug before servicing.; Remove 1 screw at the left side of GUIDE TUB
Disassembly and Reassembly _ 5 2-2. CAP CASE BRAKE / GASKET BRAKE - Cap Case Brake : DD81-01387A / SVC-AIR BREAKER NUT - Gasket Brake : DD81-01388A / SVC-SEAL RING Part Figure Description CAP CASE BRAKE / GASKET BRAKE A B [DISASSEMBLY] 1. Remove 3 screws that connect left SIDE PANEL to front side of...
Page 6 - _ Disassembly and Reassembly; Part; Take off the CAP CASE BRAKE by rotating to; Remove the GASKET BRAKE from the CASE
6 _ Disassembly and Reassembly Part Figure Description CAP CASE BRAKE / GASKET BRAKE 4. Take off the left SIDE PANEL. Warning Do not this work without safety gloves. It can cause injury from sharp edge. 5. Take off the CAP CASE BRAKE by rotating to counter-clockwise direction with long-nose pliers. ...
Page 7 - Disassembly and Reassembly _ 7; Remove 8 screws fixing the ASSY CONTROL; NOTE; Remove 6 screws to take off DOOR OUTER with
Disassembly and Reassembly _ 7 2-3. DOOR HINGE - Door Hinge : DD82-01505A, DD82-01506A / SVC ASSY-DOOR LINK R, L (except DW60M****IB) Part Figure Description DOOR HINGE (except DW6*M****IB) B A [DISASSEMBLY] * PREPARATION: Remove SIDE PANEL Left & Right refer to the section of ‘CAP CASE BRAKE / ...
Page 8 - _ Disassembly and Reassembly; Remove 2 terminals that connected to; Pay attention to hook of terminals.
8 _ Disassembly and Reassembly Part Figure Description DOOR HINGE (except DW6*M****IB) Hook Hook 4. Remove 2 terminals that connected to DETERGENT DISPENSER, and 1 ground wire that connected to BRACKET DOOR FRAME. Warning Be sure to remove the power plug before servicing. Caution Pay attention to ho...
Page 9 - Disassembly and Reassembly _ 9; DOOR INNER assembly to the direction of about 15 ̊.
Disassembly and Reassembly _ 9 Part Figure Description DOOR HINGE (except DW6*M****IB) GUIDE HINGE 6. Push both ribs of GUIDE HINGE to pull out the DOOR. Warning Do not this work without safety gloves. It can cause injury from sharp edge of broken parts. About 15˚ DOOR INNER assembly 7. Do same work...
Page 10 - 0 _ Disassembly and Reassembly
10 _ Disassembly and Reassembly Part Figure Description DOOR HINGE (except DW6*M****IB) [ASSEMBLY] 1. Assemble the DOOR HINGE assembly and BRACKET DOOR FRAME with machine screws. - Screws for DOOR HINGE assembly: DD81-02764A / 4 pcs - Screws for BRACKET DOOR FRAME: DD81-02728A / 2 pcs Warning Do not...
Page 11 - Disassembly and Reassembly _ 11; Fix 8 screws to assemble the ASSY CONTROL; Fasten 6 screws to fix the
Disassembly and Reassembly _ 11 Part Figure Description DOOR HINGE (except DW6*M****IB) DW6*M****F*/DW6*M****U*/DW6*M****SS DW6*M****BB/DW60M****IB 5. Connect the wire harness to Sub PBA. Caution Make sure the Wire harness are not getting stuck in other parts. NOTE : Incase of DW6*M5*** models, plac...
Page 12 - 2 _ Disassembly and Reassembly; Insert pin or thin stick to fix the door spring.
12 _ Disassembly and Reassembly - Door Inner : DD82-01494B / SVC ASSY-INNER DOOR (DW60M6070IB) DD82-01619B / SVC ASSY-INNER DOOR (DW60M5070IB) - Door Hinge : DD82-01773A, DD82-01774A / SVC ASSY-DOOR LINK L, R (DW60M****IB) Part Figure Description DOOR INNER / DOOR HINGE (DW60M****IB) [DISASSEMBLY] *...
Page 13 - Disassembly and Reassembly _ 13
Disassembly and Reassembly _ 13 Part Figure Description DOOR INNER / DOOR HINGE (DW60M****IB) 3. Remove the 2 screws(at each side / Total 4 pcs) fixing DOOR INNER. Caution Be careful not to dent the DOOR INNER during disassembly. 4. Remove the stopper carefully. Caution Do not this work without safe...
Page 14 - 4 _ Disassembly and Reassembly; Pull the spring enough, and insert pin or thin stick
14 _ Disassembly and Reassembly Part Figure Description DOOR INNER / DOOR HINGE (DW60M****IB) Door Hinge left Door Hinge right 5. Remove the stopper carefully. Warning Do not this work without safety gloves. It can cause injury from sharp edge. Warning Be careful not to pop out the spring while disa...
Page 15 - Disassembly and Reassembly _ 15; Hang the DOOR HINGE to the hole of the spring.
Disassembly and Reassembly _ 15 Part Figure Description DOOR INNER / DOOR HINGE (DW60M****IB) 2. Hang the DOOR HINGE to the hole of the spring. Warning Do not this work without safety gloves. It can cause injury from sharp edge. 3. Assemble the stopper carefully. Warning Do not this work without saf...
Page 16 - 6 _ Disassembly and Reassembly
16 _ Disassembly and Reassembly Part Figure Description DOOR INNER / DOOR HINGE (DW60M****IB) 5. Remove pin NOTE : After servicing DOOR INNER assembly, assemble WIRE HARNESS, DOOR OUTER, CONTROL PANEL and SIDE PANEL.
Page 17 - Disassembly and Reassembly _ 17; Remove HOLDER ROPE DOOR from the DOOR; Remove HOLDER HINGE from the DOOR HINGE.; Rotate the HOLDER HINGE to release from hook.
Disassembly and Reassembly _ 17 2-4. HOLDER HINGE - Holder Hinge : DD81-01367A / SVC-GUIDE DOOR LINK Part Figure Description HOLDER HINGE [DISASSEMBLY] * PREPARATION: Disassemble SIDE PANEL left & right. 1. Remove HOLDER ROPE DOOR from the DOOR HINGE left & right with the DOOR closed. Warnin...
Page 18 - 8 _ Disassembly and Reassembly; Pull out the old seal from the BRACKET SEAL; Put some water on new SEAL TUB PACKING to; Assemble the SEAL TUB PACKING to center of the
18 _ Disassembly and Reassembly 2-5. SEAL TUB PACKING - Seal Tub Packing : DD81-01381A / SVC-GASKET TUB Part Figure Description SEAL TUB PACKING Seal tub packing Bracket seal tub [DISASSEMBLY] 1. Pull out the old seal from the BRACKET SEAL TUB. Warning Be sure to remove the power plug before servici...
Page 19 - Disassembly and Reassembly _ 19; Press the seal from the top corner toward remaining
Disassembly and Reassembly _ 19 Part Figure Description SEAL TUB PACKING About 3~4 cm 3. Put Seal in the left & right side of the bottom. NOTE : The folded seal is about 3~4 cm long. 4. Press the seal from the top corner toward remaining side. Caution Pay attention to assemble not to deform the ...
Page 20 - 0 _ Disassembly and Reassembly; Turn the COARSE FILTER counter-clockwise to
20 _ Disassembly and Reassembly 2-6. ROTOR LOWER / ASSY DUCT NOZZLE - Rotor Lower : DD81-01847A / SVC-NOZZLE LOWER - Assy Duct Nozzle : DD82-01501A / SVC ASSY-DUCT NOZZLE (DW6*M6***) DD82-01646A / SVC ASSY-DUCT NOZZLE (DW6*M5***) Part Figure Description ROTOR LOWER / ASSY DUCT NOZZLE Rotor lower [DI...
Page 21 - Disassembly and Reassembly _ 21; Put the HOLDER ROTOR LOWER on the SUMP.
Disassembly and Reassembly _ 21 Part Figure Description ROTOR LOWER / ASSY DUCT NOZZLE Sump Guide of Holder Bottom of Holder Rib [ASSEMBLY] 1. Put the HOLDER ROTOR LOWER on the SUMP. Caution Pay attention to assemble the HOLDER ROTOR LOWER correctly. There’re risks of leakage or poor performance whe...
Page 22 - 2 _ Disassembly and Reassembly; Fasten 2 screws to fit the ASSY DUCT NOZZLE.
22 _ Disassembly and Reassembly Part Figure Description ROTOR LOWER / ASSY DUCT NOZZLE 3. Fasten 2 screws to fit the ASSY DUCT NOZZLE. - Screws: DD81-02718A / 2 pcs 4. Put the ROTOR LOWER onto the HOLDER ROTOR LOWER.
Page 23 - Disassembly and Reassembly _ 23; Open the dishwasher’s DOOR, and take off the; Be careful not to break the hooks.; Make sure to fit the hook to the correct location of
Disassembly and Reassembly _ 23 2-7. ASSY ROTOR MIDDLE - Assy Rotor Middle : DD82-01500A / SVC ASSY-MIDDLE NOZZLE Part Figure Description ASSY ROTOR MIDDLE [DISASSEMBLY] 1. Open the dishwasher’s DOOR, and take off the BASKET MIDDLE. 2. Release 2 hooks to take off ASSY ROTOR MIDDLE from the BASKET MI...
Page 24 - 4 _ Disassembly and Reassembly; Turn the COARSE FILTER counter-clockwise to; Make sure to direction of MICRO FILTER when; Reassembly is the reverse order of disassembly.; Make sure the COARSE FILTER is closed securely.
24 _ Disassembly and Reassembly 2-8. COARSE FILTER / FINE FILTER / MICRO FILTER - Coarse Filter : DD81-02452A / SVC-FILTER COARSE - Fine Filter : DD81-02454A / SVC-FILTER FINE - Micro Filter : DD81-02453A / SVC-FILTER MICRO Part Figure Description COARSE FILTER / FINE FILTER / MICRO FILTER [DISASSEM...
Page 25 - Disassembly and Reassembly _ 25; Release 4 hooks of ASSY ADJUSTER (at each
Disassembly and Reassembly _ 25 2-9. BASKET MIDDLE / ASSY ADJUSTER / BRACKET ADJUSTER - Basket Middle : DD82-01496E / SVC ASSY-BASKET UPPER (DW6*R707***/DW6*R705***) DD82-01496F / SVC ASSY-BASKET UPPER (DW6*R704***) - Assy Adjuster : DD82-01719B, DD82-01720B / SVC ASSY-ADJUSTER L, R) - Bracket Adjus...
Page 26 - 6 _ Disassembly and Reassembly; Take off the REMOVABLE TINE by releasing hooks.
26 _ Disassembly and Reassembly 2-10. BASKET LOWER - Basket Lower : DD82-01498* / SVC ASSY-BASKET LOWER (DW6*M6***) DD82-01645A / SVC ASSY-BASKET LOWER (DW6*M5***) Part Figure Description BASKET LOWER [DISASSEMBLY] 1. Open the dishwasher’s DOOR, and take off the BASKET LOWER. 2. Release 2 screws to ...
Page 27 - Disassembly and Reassembly _ 27
Disassembly and Reassembly _ 27 2-11. BASKET 3 rd - Basket 3 rd : DD82-01499A / SVC ASSY-BASKET 3rd (DW6*M6***, except DW6*M604*) Part Figure Description BASKET 3 rd [DISASSEMBLY] 1. Open the dishwasher’s door, and take off the BASKET 3 rd from the RAIL BASKET. 2. When you take off the BASKET 3 rd, ...
Page 28 - 8 _ Disassembly and Reassembly; Take off the HOLDER RAIL REAR by pulling back; Put the RAIL BASKET on the ROLLER RAIL.; Assemble the HOLDER RAIL REAR to RAIL
28 _ Disassembly and Reassembly 2-12. RAIL BASKET / HOLDER RAIL REAR - Rail Basket : DD81-01379A, DD81-01413A / SVC-RAIL BASKET L, R DD82-01169A, DD82-01170 / SVC ASSY-RAIL BASKET 3RD R, L (DW6*M6***, except DW6*M604*) - Holder Rail Rear : DD81-01378A / SVC-STOPPER RAIL REAR DD81-01674A / SVC-STOPPE...
Page 29 - Disassembly and Reassembly _ 29; This part will be serviced by assembly part only.
Disassembly and Reassembly _ 29 2-13. BASKET CUTLERY - Basket Cutlery : DD82-01147A / SVC ASSY-CASE SPOON (DW6*M604***/DW60M5050**/DW60M5070IB/DW6KM5031BB) Part Figure Description BASKET CUTLERY [DISASSEMBLY / ASSEMBLY] 1. This part will be serviced by assembly part only.
Page 30 - 0 _ Disassembly and Reassembly; Release the cap of softener by rotating to counter-
30 _ Disassembly and Reassembly 2-14. CAP SOFTENER - Cap Softener: DD81-01678A / SVC-CASE SOFTENER Part Figure Description CAP SOFTENER Cap Softener [DISASSEMBLY] 1. Release the cap of softener by rotating to counter- clockwise. [REASSEMBLY] 1. Reassembly is the reverse order of disassembly.
Page 31 - Disassembly and Reassembly _ 31; CHECKPOINTS AFTER FINISHING A SERVICE; Check whether the dishwasher is level.
Disassembly and Reassembly _ 31 3. CHECKPOINTS AFTER FINISHING A SERVICE 1. Check the safety device Check the operation of the door lock switch. Make sure that it is locked while the dishwasher is running and that it is unlocked when the dishwasher stops. 2. Use authenticated parts only If any part ...
Page 32 - Asia
© 2021 Samsung Electronics Co.,Ltd. All rights reserved. Printed in Korea GSPN (GLOBAL SERVICE PARTNER NETWORK) Area Web Site Eurpoe, CIS, Mideast & africa gspn1.samsungcsportal.com Asia gspn2.samsungcsportal.com North & Latin America gspn3.samsungcsportal.com China china.samsungportal.com T...
