Samsung DW60M5042FS - Repair Manual

Table of Contents:

• Page 2 – IMPORTANT SAFETY NOTICE; WARNING; choose the right part name.
• Page 3 – Tools for Removal and Reassembly _ 3; TOOLS FOR REMOVAL AND REASSEMBLY; Tool image; Adjustable Wrench; Preparation for parts replacement; You must turn off the circuit breaker connected to the product.
• Page 4 – _ Standard Disassembly Drawings; STANDARD DISASSEMBLY DRAWINGS; Caution; → There is a risk of water spill on the floor.
• Page 5 – Standard Disassembly Drawings _ 5; Remove 3 screws that connect left SIDE PANEL to; Warning; Be sure to remove the power plug before servicing.; Remove 1 screw at the left side of GUIDE TUB
• Page 6 – _ Standard Disassembly Drawings; Part; Take off the CAP CASE BRAKE by rotating to; Remove the GASKET BRAKE from the CASE
• Page 7 – Standard Disassembly Drawings _ 7; Remove 8 screws fixing the ASSY CONTROL; NOTE; Remove 6 screws to take off DOOR OUTER with
• Page 8 – _ Standard Disassembly Drawings; Remove 2 terminals that connected to; Pay attention to hook of terminals.
• Page 9 – Standard Disassembly Drawings _ 9; Push both ribs of GUIDE HINGE to pull out the DOOR.; Do same work at the opposite side, and pull out the; Remove 2 screws to take off BRACKET DOOR; Remove 2 screw at each side to take off DOOR
• Page 10 – 0 _ Standard Disassembly Drawings
• Page 11 – Standard Disassembly Drawings _ 11; Fix 8 screws to assemble the ASSY CONTROL; Fasten 6 screws to fix the
• Page 12 – 2 _ Standard Disassembly Drawings; Remove HOLDER ROPE DOOR from the DOOR; Remove HOLDER HINGE from the DOOR HINGE.; Rotate the HOLDER HINGE to release from hook.
• Page 13 – Standard Disassembly Drawings _ 13; Pull out the old seal from the BRACKET SEAL; Put some water on new SEAL TUB PACKING to; Assemble the SEAL TUB PACKING to center of the
• Page 14 – 4 _ Standard Disassembly Drawings; Press the seal from the top corner toward remaining
• Page 15 – Standard Disassembly Drawings _ 15; Turn the COARSE FILTER counter-clockwise to
• Page 16 – 6 _ Standard Disassembly Drawings; Put the HOLDER ROTOR LOWER on the SUMP.; Assemble the ASSY DUCT NOZZLE to hooks and
• Page 17 – Standard Disassembly Drawings _ 17; Fasten 2 screws to fit the ASSY DUCT NOZZLE.
• Page 18 – 8 _ Standard Disassembly Drawings; Open the dishwasher’s DOOR, and take off the; Be careful not to break the hooks.; Make sure to fit the hook to the correct location of
• Page 19 – Standard Disassembly Drawings _ 19; Turn the COARSE FILTER counter-clockwise to; Make sure to direction of MICRO FILTER when; Reassembly is the reverse order of disassembly.; Make sure the COARSE FILTER is closed securely.
• Page 20 – 0 _ Standard Disassembly Drawings; Release 4 hooks of ASSY ADJUSTER (at each
• Page 21 – Standard Disassembly Drawings _ 21; Take off the REMOVABLE TINE by releasing hooks.
• Page 22 – 2 _ Standard Disassembly Drawings
• Page 23 – Standard Disassembly Drawings _ 23; Take off the HOLDER RAIL REAR by pulling back; Put the RAIL BASKET on the ROLLER RAIL.; Assemble the HOLDER RAIL REAR to RAIL
• Page 24 – 4 _ Standard Disassembly Drawings; This part will be serviced by assembly part only.
• Page 25 – Standard Disassembly Drawings _ 25; Release the cap of softener by rotating to counter-
• Page 26 – 6 _ Checkpoints After Finishing A Service; CHECKPOINTS AFTER FINISHING A SERVICE; Check whether the dishwasher is level.
• Page 27 – Asia