Rheem Indirect Water Heater- User Manual

Rheem Indirect Water Heater

Rheem Indirect Water Heater– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
Page: / 16

Table of Contents:

  • Page 2 – Page 2; TABLE OF CONTENTS
  • Page 3 – SECTION I: SPECIFICATIONS; Model
  • Page 4 – Page 4
  • Page 5 – SECTION II: GENERAL INFORMATION; loCaTIon; Long heating supply runs can lengthen recovery times.; WaTer TreaTmenT/fIlTraTIon; CAUTION: Hot water in excess of 120; IMMERSION CONTROL; APPROXIMATE
  • Page 6 – Page 6; anode rods; Hydrogen gas is produced in a hot water system served by this; water; heater that has not been used for a long
  • Page 7 – boIler and CIrCulaTor sIzIng; Figure 3: Taco 00 Series performance curves
  • Page 8 – Page 8; Figure 4: GRUNDFOS UP 15-42F performance curve; and will drastically reduce performance.
  • Page 9 – Figure 7: STID80, STID120 water connections; SECTION IV: INSTALLATION; WaTer ConneCTIons; See Figures 6 and 7 for proper water connection installation.
  • Page 10 – Figure 8: Rheem Indirect Water Heater with Low-Mass Boiler
  • Page 11 – eleCTrICal ConneCTIons; THERMOSTAT SPECIFICATIONS:; Figure 9: Boiler Maintaining 180°F; Burner
  • Page 12 – SECTION V: MAINTENANCE; WaTer pIpIng; Open any faucet to relieve tank pressure.; flusH THe Tank
  • Page 13 – SECTION VI: TROUBLESHOOTING
  • Page 14 – SECTION VII: PARTS LIST; Description; Anode
  • Page 16 – EXCLUSIVE WARRANTY – LIMITATION OF LIABILITY; DO NOT RETURN THIS DOCUMENT TO RHEEM.
Loading the manual

#23960

P1ge 1

WARNING

Improper installation, adjustment, alteration,
service or maintenance can cause serious injury
or property damage. Refer to this manual. For
assistance or additional information, consult a
qualified installer or service agency.

CAUTION

The recommended temperature for normal
residential use is 120°F. The dial on the aquastat
does not always reflect the out-coming water
temperature, which could occasionally exceed
120°F. The variation in out-coming temperature
could be based on factors including but not
limited to usage patterns and type of installation.
Test your water at the tap nearest to the indirect
water heater.

WARNING

Hotter water increases the risk of scald injury.
Before adjusting the water temperature setting,
read this instruction manual. Temperatures at
which injury occurs vary with the person’s age
and the length of exposure.
The slower reaction time of children, elderly, and
physically or mentally challenged persons
increases the scalding hazard to them. It is
recommended that lower water temperatures be
used where these exposure hazards exist. Such
households may require a temperature setting
less than 120°F to prevent accidental contact
with hot water.
To lower water temperature use point-of-use
temperature limiting devices.

WARNING

Water heater blankets are not recommended and
will void the warranty.

THIS MANUAL HAS BEEN PREPARED

TO ACQUAINT YOU WITH THE INSTALLATION,

OPERATION, AND MAINTENANCE OF

YOUR INDIRECT WATER HEATER AND TO PROVIDE

IMPORTANT SAFETY INFORMATION.

INSTALLER RESPONSIBILITIES

Please read all instructions thoroughly before
installing or placing the indirect water heater
into service. This unit must be installed by
licensed or authorized installers, or technical
personnel that service water heating equipment.
The indirect water heater must be installed in
accordance with all local codes and ordinances.
These instructions are a guide for the correct
installation of the indirect water heater. The
manufacturer will not be liable for damages caused
by failure to comply with the installation and
operating instructions outlined on the following
pages.

CAUTION

The recommended water temperature setting for
normal residential use is 120°F/49°C.

HANDLING

Before uncrating, check for shipping damage.
Report any damage to your carrier. Note damage on
bill of lading or delivery receipt and file a claim.

FAILURE TO FOLLOW THESE INSTRUCTIONS OR ALL

APPLICABLE BUILDING CODES AND REGULATIONS

VOIDS THE WARRANTY

ON THIS INDIRECT WATER HEATER.

Read all instructions thoroughly before

attempting installation or operation of your

indirect water heater. Keep these instructions for

future reference.
Local plumbing and electrical codes must be
followed in the installation of this indirect water

heater. In the absence of a local code use the

UNIFORM PLUMBING CODE and the NFPA Code.

Local codes may supersede instructions in this

installation manual.
These instructions are a guide for the correct
installation of the indirect water heater. The

manufacturer will not be liable for damages

caused by failure to comply with the installation

and operating instructions outlined on the

following pages.

Warranty and Parts List are included.

To the Consumer:

Please read these and all component

instructions and keep for future reference.

To the Installer:

Please attach these instructions

next to the indirect water heater.

Indirect Water Heater

Instruction Manual

Rev 1 5/08

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Other Manuals for Rheem Indirect Water Heater

Summary

Page 2 - Page 2; TABLE OF CONTENTS

Page 2 TABLE OF CONTENTS Section I: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Section II: General Informations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sect...

Page 3 - SECTION I: SPECIFICATIONS; Model

Page 3 G Cold Inlet, 3/4" NPT Hot Outlet/ Anode Rod, 3/4" NPT Anode Rod Aquastat T&P Relief Valve From Boiler Supply, 1" NPT To Boiler Return, 1" NPT Drain Valve F D C E B A SECTION I: SPECIFICATIONS Foam insulation standard on indirect water heater models. Pressures, all: Test p...

Page 4 - Page 4

Page 4 SECTION I: SPECIFICATIONS (cont .) STID30 30 1.38 110 85 25 55,000 1.3 2.0 STID40 38 2.30 153 120 33 77,000 1.1 3.0 STID50 45 2.30 160 120 40 77,000 1.0 3.0 STID80 75 2.76 200 130 70 83,000 0.9 5.0 STID120 110 2.76 232 130 102 83,000 1.2 5.0 Model Actual Tank Volume (gal) Coil Volume (gal) Fi...

Other Rheem Models