Regency P121/P131-NG2 - Manual
Regency P121/P131-NG2 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Framing and Finishing; Frame in the enclosure for the unit with framing material.; Combustible Mantels; Combustible mantel clearances from top of; Parallel Wall Clearances; Min distance from glass to a parallel wall; WARNING; Clearance Requirements; Gas Fireplaces
- Page 3 – AstroCap; Snorkel Ter minations; Snorkel Terminations:; Alternate Horizontal; June 2007 Regency Product Specifi cations Book
- Page 4 – Rigid Pipe System; The P121 /131 is approved for a maximum 35 ft. straight vertical, with; Maximum; Two 45° elbows = One 90° elbow; Option; IMPORTANT; When installing this unit vertically, the 45 ̊; Rigid Pipe Venting
- Page 6 – Venting Arrangements - Horizontal; This diagram shows allowable venting confi gurations; Note: FPI Direct Vent System (Flex) is only approved for horizontal
P121 - P121LC/RC - P131 Zero Clearance Direct Vent Gas Fireplace
Model
P121/P131-NG2
P121/P131-LP2
Fuel Type
Natural Gas
Propane
Minimum Supply Pressure
5” W.C. (1.25 kPa)
12” W.C. (3.00 kPa)
Manifold Pressure - High
3.8” W.C. (0.95 kPa)
11” W.C. (2.74 kPa)
Manifold Pressure - Low
1.1” W.C. (0.27 kPa)
2.9” W.C. (0.72 kPa)
Orifi ce Size
#31 DMS
#50 DMS
Minimum Input
20,500 BTU/h (6.01 kW)
20,600 BTU/h (6.04 kW)
Maximum Input
40,000 BTU/h (11.72 kW)
39,000 BTU/h (11.43 kW)
Vent Sizing
4” Inner / 6-5/8” Outer
4” Inner / 6-5/8” Outer
P
Gas Line
Inlet
Electrical
Inlet
BACK
N
O
M
A
D
C
G
E
B
F
P121 See Thru
P131 Pier
P121RC Right Corner
P121LC Left Corner
Unit Dimensions
Description
P121
P121LC/RC
P131
A
Front Face Width
43-1/2”
(1105mm)
41-1/2”
(1054mm)
41-1/2”
(1054mm)
B
Total Firebox Width
46-1/4”
(1175mm)
44-1/2”
(1130mm)
44-1/2”
(1130mm)
C
Front Face Height
36” (914mm)
36” (914mm)
36” (914mm)
D
Height w/ Standoff
42” (1067mm)
42” (1067mm)
42” (1067mm)
E
Unit Depth
25” (635mm)
26-13/16”
(681mm)
25” (635mm)
F
Top Offset Depth
21-1/8”
(537mm)
21-1/8”
(537mm)
21-1/8”
(537mm)
G
Inset to Standoff
4-3/4”
(121mm)
4-3/4”
(121mm)
3” (76mm)
H
I
J
K
Combustible
Material
3”
Extension
Trim
Non-Combustible
Material *
Top of
Unit
8”
Greyed out framing will not apply to all units.
Please refer to the manual.
L
Framing Dimensions Description
P121
P121LC/RC
P131
H
Framing Width
46-3/4”
(1187mm)
45”
(1143mm)
**
45”
(1143mm)
**
I
**
Framing Height
**
42-1/2”
(1080mm)
42-1/2”
(1080mm)
42-1/2”
(1080mm)
J
**
Framing Depth
**
25” (635mm)
**
26-13/16”
(681mm)
25” (635mm)
**
K
Vent Centerline Height
42-13/16” (1072mm)
L
Framed Chase Ceiling
48-1/4” (1226mm)
M
Electrical Inlet Height
2” (51mm)
2” (51mm)
2” (51mm)
N
Electrical Inlet Inset
11-3/8”
(289mm)
13-5/16”
(338mm)
11-3/8”
(289mm)
O
Gas Connection Height
1-11/16”
(43mm)
1-11/16”
(43mm)
1-5/8” (41mm)
P
Gas Connection Inset
11-1/2”
(292mm)
11-1/2”
(292mm)
11-1/2”
(292mm)
**
Refer to the manual for variations effected by fi nishing material
thickness.
P121-P131 Gas Fireplace
If the provided 3” extension trim is not installed the P121(LC/RC)/
P131 must be installed with non-combustible facing up to 8” above
the fi replace. Otherwise combustible facing may be used above the
extension trim.
Approved Venting Systems
Flex Vent Systems:
FPI AstroCap™ Flex Vent
Rigid Pipe Vent Systems:
Simpson Dura-Vent® Direct Vent GS
American Metal Products Ameri Vent
Security Secure Vent®
Selkirk Direct-Temp.
Please refer to Page 11 (Exterior Vent Terminations)
for additional guidelines on vent locations.
69
June 2007 Regency Product Specifi cations Book
Gas Fireplaces
Gas Fir
eplaces
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Framing and Finishing 1) Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the fi nished surface to be fl ush with the front of the unit. Total facing thickness can vary from 1/2” (13mm) to 1-¼” (32mm) thick. 2) Frame in the enclosure for the unit with framing...
Regency Direct Vent System (Flex) Horizontal Terminations Only These venting systems, in combination with the P121/P131 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock Hersey. The location of the termination cap must conform to the requirements in the...
Rigid Pipe Adapter 1-1/2”(38mm) 45 Elbow o Venting Arrangements - Ver tical Ter minations Rigid Pipe System (Propane & Natural Gas) The P121 /131 is approved for a maximum 35 ft. straight vertical, with Rigid Pipe vent systems for Propane and Natural Gas. • Vent must be supported at offsets. • H...
