Page 3 - WARNING; To prevent injury or fire, take the following precautions:; PYLE; To prevent damage to the Unit, take the following precautions:; Do not load 3-inch CDs in the CD slot; Safety precaution
1 WARNING To prevent injury or fire, take the following precautions: Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of placewhen jolted. When extending the ignition, battery, or ground wire, make sure to use automotive-gradewires or other wires with a 0.7...
Page 4 - CONTENTS
2 CONTENTS Safety Precaution (p4) About CDs (p5) Introduction (p6) 1. Region Number .......................................... (p6)2. Control Parts .............................................. (p6) 2-1. With Display Closed ............................ (p7)2-2. With Display Opened ....................
Page 5 - CLASS 1
3 The marking of products using lasers (Except for some areas) NOTE If you experience problems during installation, consult your PYLE dealer. If the unit fails to operate properly, press the Reset button. The unit returns to factorysetting when the Reset button is pressed. If the unit still fails to...
Page 7 - About CDs; CAUTION
Removing CDs W h e n r e m o v i n g C D s f r o m t h i s u n i t , p u l lthem out horizontally. CDs that can t be used CDs that aren t round can t be used. C D s w i t h c o l o r i n g o n t h e r e c o r d i n g surface or that are dirty can t be used. T h i s u n i t c a n o n l y p l a y t h ...
Page 8 - -1 With Display Closed; INTRODUCTION; This DVD Player is designed for use in Region 1 (North America).; If a disc is identified as Region 0 it will work on any DVD Player.
2. Control Parts 2-1 With Display Closed 6 INTRODUCTION The region number of this Unit is labeled on therear panel of the unit. Most DVD s are manufactured specifically forsale and use in a specific geographic region. A disc s Region Number must correspond to theR e g i o n N u m b e r o f t h i s U...
Page 9 - WITH THE DISPLAY CLOSED
7 Volume Up/Down Use this button to increase/decrease the volume. Tilt Use this button to adjust the angle of the TFT LCD panel in 3 steps and every time this button is pressed with being held for about 2 second or longer, the TFT LCD panel movesbackward with 2 steps & forward with 1 step. Open/...
Page 10 - - 2 WITH THE DISPLAY OPENED
8 Track / CH Up/ Down - Use this button to tune to a station to be stored in the radio / TV mode . 1) T r a c k u p k e y w i t h p r e s s i n g o v e r 2 s e c o n d s s h o u l d b e R a d i o F r e q u e n c y o r TV Channel memory. 2) Track down key with pressing over 2 seconds should delete Ra...
Page 12 - Preparing & Using The Remote Control
10 INTRODUCTION Preparing & Using The Remote Control 4. BATTERY BATTERY INSTALLATION NOTICE (BATTERY) P L E A S E F O L L O W T H E I N S T R U C T I O N SBELOW. INCORRECT BATTERY USEAGEMIGHT CAUSE EARLY DISCHARGE, LEAKAGEOR CORROSION DAMAGE. * Do not insert battery in the wrong direction. Be su...
Page 13 - Remote Control Key
11 INTRODUCTION 5. Remote Control Key Power/ModeMuteOpen /CloseVolume Up/DownAF / TA (RDS Function)PTY/ REG (RDS Function)Track (P.Seek/CH) Up / DownBand (OSD ON / OFF)MenuEnterSet UpDVD MenuSlow Disc (Seek/Manual) Up / DownTilt / Navi (Navigation Function)Rear MonitorNTSC/PAL(DVD ONLY)P.S/BSMPlay/P...
Page 14 - Connecting to Power System; Connecting to Power & Multi Channel AV Control Unit System; Notice; not show any picture.
12 1. Connecting to Power System Connecting to Power & Multi Channel AV Control Unit System The illustration below is showing power system connection. Please also refer to theowner s and installation manuals supplied with the associated equipment. If it doesn thave corrected connection, it may c...
Page 15 - RT BOX 16P CONNECTOR WIRING DIAGRAM
13 Connecting to Power & Multi Channel AV Control Unit System 2. RT BOX 16P CONNECTOR WIRING DIAGRAM
Page 16 - Connecting to Multi Channel AV Control Unit System; D o n ’ t u s e b o t h A V 2 a n d D V D / V C D C h a n g e r I n p u t a t t h e s a m e t i m e b e c a u s e; NOTICE
14 3. Connecting to Multi Channel AV Control Unit System The Illustration below is just possible examples with our Multi Channel AV Control UnitS y s t e m o n l y . T h e e x a c t c o n n e c t i o n m e t h o d w i l l v a r y d e p e n d i n g o n t h e s p e c i f i ccomponents selected for a p...
Page 17 - Connecting to DVD Changer Control System; D o n ’ t u s e A V 2 A u d i o L / R i n p u t o f R T B o x w h e n D V D C h a n g e r i s C o n n e c t e d .
15 4. Connecting to DVD Changer Control System D o n ’ t u s e A V 2 A u d i o L / R i n p u t o f R T B o x w h e n D V D C h a n g e r i s C o n n e c t e d . You can just use only AV2 Video input of RT Box from DVD Changer Video output. In case of using CD Changer instead of DVD Changer, the AV2 ...
Page 18 - NOTE
16 5. Connecting to Multi Channel AV Control Unit System with Additional 6CH Amplifier The Illustration below is just possible examples for our Multi Channel AV Control UnitSystem with Additional 6CH Amplifier. The exact connection method will vary dependingon the specific components selected for a ...
Page 19 - CLOSING THE MONITOR
17 BASIC O OPERATION CLOSING THE MONITOR 1. Hold the left and right upper side of the m o n i t o r p a r a l l e l w i t h t h e f r o n t o f t h e unit as the picture below. 2. Press OPEN button or POWER button, and then the monitor will be closed. NOTE 1. If the left and right angle of the monit...
Page 20 - BASIC OPERATION; AUDIO CONTROL
18 BASIC OPERATION 3. Use key and place cursor (Yellow b a r ) o n t h e i t e m y o u w a n t t o a d j u s t ( E x . T o n e / V o l u m e ) a n d p r e s s E N T E R k e y a s p i c t u r e b e l o w . 4. Use key and place cursor (Yellow bar) on the sub-item you want to adjust( E x . B a s s ) a ...
Page 24 - REAR MONITOR
22 5. Press ENTER key at least for 2 seconds to return to the previous screen. 6. Use key and place cursor (Yellow bar) on Angle and press ENTER key aspicture below. 7. Each time you press ENTER key, Angle changes as below. 0 deg --> 180 deg 8. Press ENTER key at least for 2 seconds o n c u r r e...
Page 25 - AUTO TILT SYSTEM
23 BASIC OPERATION * When no key is pressed for 5 seconds, the menu will disappear. RDS (Radio Data System) 1. P r e s s M E N U k e y u n t i l t h e m o n i t o r d i s p l a y s f o l l o w i n g p i c t u r e . 2. Use Key and place cursor (Yellow Bar) on RDS and press ENTER key. 3. Use Key and p...
Page 26 - OVERVIEW OF THE RDS FUNCTION
24 TUNING (TV-AUTO SEARCH) 1. After adjust TV system(Field/Standard) on Pre-Adjust, Press P.S/BSM to searchTV channels. * ‘Searching’ will be blinking as it searches T V c h a n n e l s a n d c h a n n e l n u m b e r i s changing as it searches TV channels. 2. W h e n A u t o - S e a r c h i s c o ...
Page 28 - About 2CH or 6CH Setup:; CHANGING DVD SYSTEM SETTING; DVD VIDEO PLAYER OPERATION
26 About 2CH or 6CH Setup: I f 2 C H i s s e t i n t o t h i s m e n u w i t hAnalog out, it’s sound will come out by2CH even though DVD title was set by5.1CH Sound. To enjoy Dolby Digitalor DTS Sound with Analog out, thismenu must be set by 6CH with DolbyDigital and DTS Category and DVDtitle also h...
Page 30 - How to use Remocon
28 1) POWER /MODE Use this button to turn on/off. For Turn - off, hold this button about 2 seconds orlonger. Each time This button is pressed, its source should be changed to AV1 AV2 DVD RADIO TV. 2) OPEN /CLOSE Use this button to open/close the TFT LCD Panel. 3) EJECT Use this button to eject a dis...
Page 31 - ) C H A N G I N G A U D I O S O U N D T R A C K
29 DVD VIDEO PLAYER OPERATION 5) CHANGING SUBTITLE LANGUAGE (S -TITLE) I t i s p o s s i b l e t o c h a n g e t h e s u b t i t l elanguage to a different language from theselected one. This operation works only w i t h d i s c s o n w h i c h m u l t i p l e s u b t i t l e languages are recorded....
Page 32 - NAVIGATION & MOVEMENT
30 DVD VIDEO PLAYER OPERATION P l a y b a c k o f t h e s e l e c t e d i t e m w i l lb e g i n . 8) REPEAT (SET UP) T o r e p e a t v i e w i n g o r l i s t e n i n g , p r e s s R E P E A T d u r i n g p l a y b a c k . E a c h t i m ethis button is pressed, the TV Screen changes as below. Repea...
Page 33 - After playback; a p p e a r s o n t h e s c r e e n w h e n a
31 DVD VIDEO PLAYER OPERATION For further information, also refer to anyinstructions that may have been packagedwith the disc you are playing. After playback When the unit is not in use, remove the disca n d t u r n o f f t h e p o w e r b y p r e s s i n g t h ePOWER button.(Do not remove the disc ...
Page 34 - Adjust the Volume by pressing the VOLUME
32 This unit is equipped with a LAST MEMORYfunction which lets you resume viewing of amovie from the point where you left off. Youmust press only PLAY button, not Power buttoni n c a s e t h e p o w e r h a s b e e n t u r n e d o f f ( a n dstand by power) NOTE The Last Memory function is not suppo...
Page 36 - AM/FM RADIO OPERATION
34 1. BAND (AM / FM) Each time this button is pressed, the band will be changed to FM1 FM2 FM3 AM1 AM2 2. PRESET SCAN / BSM Following your desired band selection, pressP.S/BSM button about 2 seconds or longer,and then tuner will search until stations ofsufficient strength have been found and wills t...
Page 37 - TV OPERATION
35 1. PRESET SCAN / BSM Firstly, select the desired station and press thePS/BSM button shortly. And then, Tuner willnow search until stations of sufficient strengthhave been found and will store them into TFTLCD automatically in sequence. 2. MANUAL UP/ DOWN To find out a desired TV channel, press th...
Page 38 - INSTALLATION; Adjust the mounting angle to less than 20
INSTALLATION 36 PRECAUTIONS Choose the mounting location carefully so that the unit will not interfere with the normaldriving functions of the driver. Avoid installing the unit where it would be subject to hightemperatures, such as from direct sunlight or hot air from the heater or where it would be...
Page 39 - SUPPLIED MOUNTING KIT; BRACKET
37 INSTALLATION Make sure that the unit is installed securely in place. If the unit is unstable, it maymalfunction. For example, the source may skip. 1. Align the holes in the unit with the vehicle mounting bracket and secure the unit with the accessory screws. 2. During installation, do not use any...
Page 40 - SPECIFICATIONS; Weight of the Remote Control Unit: 70g
SPECIFICATIONS FM TUNER Frequency Range: 87.50 MHz to 108.0 MHzUsable Sensitivity: 9 dBf50dB Quieting Sensitivity: 15 dBfAlternate Channel Selectivity: 70 dBStereo Separation (1 kHz): 30 dBFrequency Response ( 3 dB): 30Hz to 15 kHz AM TUNER Frequency Range: 530kHz to 1710kHzUsable Sensitivity: 25 dB...
Page 41 - PRINTED IN KOREA
WARNING DO NOT HOLD THE LCD SCREEN PANEL WHILE IT ISO P E N I N G O R C L O S I N G U N T I L I T I S C O M P L E T E LYOPENED OR CLOSED. OTHERWISE, THE MOTORIZEDMECHANISM WILL BE DAMAGED. BEFORE WORKING THE UNIT, READ THE OWNER SM A N U A L C A R E F U L LY A N D F O L L O W U P T H EINSTRUCTIONS I...
