Precor UBK 800 - Manual

Important Safety Instructions 5  If you plan to move the equipment, obtain help and use proper lifting techniques. Refer to the "Moving the Equipment" section of the assembly and maintenance guide.  Use the equipment only for its intended purpose as described in this manual. Do not use acc...

6 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Hazardous Materials and Proper Disposal The batteries within self-powered equipment contain materials that are considered hazardous to the environment. Federal law requires proper disposal of these batteries. If you plan to dispose o...

Important Safety Instructions 7 Radio Frequency Interference (RFI) The RFID module conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to comply with the li...

Important Safety Instructions 9 Radio Frequency Interference (RFI) This Precor exercise equipment conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to com...

Table of Contents Important Safety Instructions ................................................... 3 Safety Precaution s .................................................................................3 Educating Users ..................................................................................

Chapter 1 Assembling the Exercise Bike Important: The instructions in the following procedures are described from the perspective of a person standing directly in front of the equipment (that is, on the opposite side of the control console from a person using the equipment). These descriptions may n...

14 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Unpacking the Equipment The shipping container for Precision Series exercise bikes consists of the following items:  Wooden pallet  Cardboard base  Cardboard cover WARNING Do not attempt to move the equipment off of the pallet by...

Assembling the Exercise Bike 15 Hardware Kit (not to scale) Before you begin the assembly, verify that the following hardware items are packed with the equipment. Fasteners Quantity ⁵₁₆ -inch x ³₄ -inch sockethead screw 4 ¹₄ -inch x ⁵₈ -inch flathead machine screw 4 #8 x ⁵₈ -inch self-tapping s...

16 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Installing the Upright Support and Cables DANGER Do not attempt to connect electrical power until all assembly procedures are complete and the console is properly installed. Before you begin this procedure, retrieve the cables for t...

Assembling the Exercise Bike 17 4. Remove the four #10 x 1-inch self-tapping screws holding the left side cover in place, then pull the cover away from the body assembly. Guide the cover around the pedal crank, then remove it and set it aside. Figure 4: Side cover removal 5. Remove the tape holding ...

18 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Note: If the support is positioned correctly, it rests on a metal tab in the upright support channel. Figure 5: Upright support insertion Important : In the following step, be extremely careful not to trap or pinch any of the cables...

Assembling the Exercise Bike 19 Installing the Bottle Holder The bottle holder attaches to a plastic support that has been mounted on the upright support at the factory. To install the bottle holder: 1. Position the bottle holder on its support so that the three tabs on the bottle holder fit into th...

20 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Installing the Handlebars After the upright support and the bottle holder are securely in place, install the handlebar assembly and route the heart rate sensor cable through the support. To install the handlebars: 1. Position the ha...

Assembling the Exercise Bike 21 Making Sure the Unit Is Stable Make sure the unit is level before allowing anyone to use it. CAUTION: To eliminate movement, make sure the adjustable feet are in contact with the floor. To level the unit: 1. Gently rock the unit. If there is any movement, ask your ass...

Chapter 2 Installing the Console To make installation easier, all Precor Experience Series consoles use the same mounting hardware and connector locations whenever possible. The installation sequence for any of them is as follows:  Threading the cable assembly  Connecting cables  Completing the i...

24 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Important : Before you begin the following procedure, remove the rear cover from the control console. To remove the cover, use your fingernails to pry the lower edge loose, then swing the cover up and out as shown in the following i...

Installing the Console 25 Connecting Cables (P80) After the console has been seated, separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to identify the cables and conne...

26 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Cable Connector Type Circuit Connector Location Heart rate sensors Four-contact strip, keyed Safety key (treadmills only) Six-contact strip, keyed CSAFE Eight-contact modular, on flat gray cable Auto Stop sensor (treadmills only) Fo...

Installing the Console 27 The following illustration shows how the cable is positioned once it is installed. Figure 12: Connecting the television cable Connecting the Ethernet and Base Unit Data Cables Both the Ethernet and base unit data cables pass through the cutaway opening at the upper right co...

28 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Connecting the Heart Rate Sensor Cable The heart rate sensor cable passes through the cutaway opening at the upper left corner of the back plate, then down to the small circuit board at the lower left of the console. The following i...

Installing the Console 29 Completing the Console Installation (P80) Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly. To complete the installat...

34 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Verifying That the Heart Rate Display Is Operational To verify that the heart rate display is operational: 1. Begin exercising on the equipment. 2. Grasp both touch-sensitive handlebars. Note: The heart rate is read within ten secon...

Chapter 3 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklist. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk ...

36 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Alternatively, you can clean the equipment with Athletix fitness equipment cleaning wipes (for more information, visit www.athletixproducts.com ) CAUTION Vacuum the floor underneath the equipment frequently to prevent the accumulati...

Maintenance 37 Quarterly Maintenance Precor recommends that you clean and inspect the equipment more thoroughly once every three months. To perform quarterly maintenance: 1. Remove the cover panels. 2. Vacuum out any debris, being careful not to bring the vacuum cleaner nozzle too close to any circu...

38 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Moving the Equipment The equipment is very heavy. If you plan to move it to a new location, obtain the help of an adult assistant and use proper lifting techniques. If the equipment includes roller wheels on one end, use the wheels ...

Chapter 4 Self-Powered Features Important : This chapter of the manual describes Precor fitness equipment that can operate without being connected to AC power. This includes units equipped with P40 or P20 consoles. However, P80 consoles must be connected to AC power through their power supplies to o...

40 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Informational Displays Prior to Shutdown The equipment saves its battery charge by moving into a shutdown mode. If the user does not maintain the minimum rate of motion, a 30-second shutdown process begins. In this mode, the console...

Self-Powered Features 41 Using the Optional Power Adapter After connecting the power adapter to the equipment, plug the opposite end into the appropriate power source (120 V or 240 V). CAUTION: When the optional power adapter is in use, make sure that the power supply cord does not create a safety h...

42 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Replacing the Battery The equipment’s battery is built to last for a long time. However, if you feel that the battery may need replacing, check with an authorized service technician. Refer to Obtaining Service . CAUTION: The battery...

Chapter 5 Commercial Cardiovascular Equipment Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS. Limited Warranty. Precor Inco...

44 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes Options / Accessories Many options or accessories have components that are connected internally or mounted inside the electronic console. The following guidelines determine the warranty for these components. If the internal componen...

46 Assembling and Maintaining UBK 800-Series Upright Exercise Bikes EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES. PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT (INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRIC...