Precor TRM 800 - Manual

Important Safety Instructions 5  When using the treadmill, always attach the safety clip to your clothing before beginning your workout. Failure to use the safety clip may pose a greater risk of injury in the event of a fall.  Also, verify that the running belts on treadmills are clean and running...

6 Assembling and Maintaining TRM 800-Series Treadmills Educating Users Take time to educate users about the Important Safety Instructions found in both the User Reference Manual and Product Owner’s Manual . Explain to your club or facility patrons that they should observe the following precautions: ...

Important Safety Instructions 7 Product Recycling and Disposal This equipment must be recycled or discarded according to applicable local and national regulations. Product labels, in accordance with European Directive 2002/96/EC concerning waste electrical and electronic equipment (WEEE), determine ...

8 Assembling and Maintaining TRM 800-Series Treadmills Radio Frequency Interference (RFI) The RFID module conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and foun...

Important Safety Instructions 9 European Applications CE compliance is claimed to the following directives:  1999/5/EC R&TTE Directive  2006/95/EC LVD Directive  2002/95/EC RoHS Directive Directive compliance has been verified to the following standards:  EN 55022  EN 300 330-1 V1.5.1  EN ...

Important Safety Instructions 11 Treadmill Grounding Instructions The treadmill must be grounded. If the equipment malfunctions or breaks down, grounding draws off electric current and reduces the risk of electric shock. The power cord on the treadmill is equipped with a grounding conductor and a th...

12 Assembling and Maintaining TRM 800-Series Treadmills Important : An individual branch circuit provides a hot conductor and neutral conductor to a receptacle. The conductors must not be looped, "daisy-chained", or connected to any other conductors. The circuit must be grounded according to...

Table of Contents Important Safety Instructions ................................................... 3 Safety Precautions .................................................................................3 Safety Code .......................................................................................

Chapter 1 Assembling the Treadmill Important: The instructions in the following procedures are described from the perspective of a person standing directly in front of the equipment (that is, on the opposite side of the control console from a person using the equipment). These descriptions may not m...

16 Assembling and Maintaining TRM 800-Series Treadmills 5. Remove the shipping fasteners from the front panel using a ¹₄ -inch hex key and a ¹⁄₂ –inch box-end wrench. 6. Remove any tape or wire ties securing the console cable to the side of the unit. Before you begin, verify that you have received ...

18 Assembling and Maintaining TRM 800-Series Treadmills Unpacking the Cables To connect the console to the base unit, you may need up to five cables, as follows:  Ethernet (P80 only)  Television (P80 only)  Power (P80 only)  Base unit data  Automatic stop sensor (Auto Stop ™ ) The first three o...

Assembling the Treadmill 19 3. Remove the seven screws holding the back cover in place. Snap the back cover loose and set it aside, along with the seven screws. Figure 4: Removal and replacement of the rear fairing cover 4. Remove the two ends of the base unit data cable from the left arm of the fai...

20 Assembling and Maintaining TRM 800-Series Treadmills 6. Remove any tape or ties that secure the cables, then unwind them and remove any kinks. Gather the cables into a single bundle (referred to later as the cable assembly ). Note: Arranging the cables so that the connectors are slightly staggere...

22 Assembling and Maintaining TRM 800-Series Treadmills To thread cables through the frame: 1. Feed the cable assembly downward through the left-hand upright support and out through the opening in the lower end of the support. Drape the remaining cable over the front of the support and tape it into ...

Assembling the Treadmill 23 Component Appearance Lower connection point Television cable Round with black insulation Console power cable Dual leads with red and black insulation Auto Stop sensor cable Round with black insulation Power supply Rectangular, black, 5" x 2 ¹₄ " x 1 ¹₄ " CAU...

Assembling the Treadmill 25 Completing Assembly After the upright supports and the fairing are in place, replace the hood on the treadmill base and finish securing the fasteners. CAUTION: Be aware of the handrail extensions when you are working around the front of the unit. It is easy to bump your h...

26 Assembling and Maintaining TRM 800-Series Treadmills Note: Using a hex wrench, reach through the openings in the outer sides of the hood to tighten the side screws. Figure 11: Hood and fastener placement Attaching the Power Cord Clips This treadmill includes a set of clips that hold the power cor...

Assembling the Treadmill 27 2. Insert the serrated portion of the clip into the hole located under the front of the unit on either side of the power switch. Figure 13: Power cord placement under front of treadmill 3. Place the clips along the length of the power cord as needed while you direct the c...

28 Assembling and Maintaining TRM 800-Series Treadmills Leveling the Unit The treadmill deck must be absolutely level from side to side to keep the belt in alignment and ensure proper operation. If the load is not equally distributed across the treadmill deck, users may feel excessive vibration or o...

Assembling the Treadmill 29 4. Adjust the rear feet as needed. Figure 16: Leveling foot adjustment 5. Repeat steps 1 through 4 until the treadmill is level. 6. If necessary, adjust the rear feet so that the user’s weight is distributed evenly on the treadmill. Plugging In the Power Cord CAUTION: Use...

Chapter 2 Installing the Console To make installation easier, all Precor Experience Series consoles use the same mounting hardware and connector locations whenever possible. The installation sequence for any of them is as follows:  Threading the cable assembly  Connecting cables  Completing the i...

32 Assembling and Maintaining TRM 800-Series Treadmills Important : Before you begin the following procedure, remove the rear cover from the control console. To remove the cover, use your fingernails to pry the lower edge loose, then swing the cover up and out as shown in the following illustration....

34 Assembling and Maintaining TRM 800-Series Treadmills Cable Connector Type Circuit Connector Location TV in F-type coaxial Power Two-contact plug, polarized and latched Data from base unit Eight-contact modular, on flat gray cable Heart rate sensors Four-contact strip, keyed Safety key (treadmills...

Installing the Console 35 The following illustration shows how the cable is positioned once it is installed. Figure 20: Connecting the television cable Connecting the Ethernet and Base Unit Data Cables Both the Ethernet and base unit data cables pass through the cutaway opening at the upper right co...

36 Assembling and Maintaining TRM 800-Series Treadmills Connecting the Heart Rate Sensor Cable The heart rate sensor cable passes through the cutaway opening at the upper left corner of the back plate, then down to the small circuit board at the lower left of the console. The following illustration ...

Installing the Console 37 Completing the Console Installation (P80) Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly. To complete the installat...

Installing the Console 39 Connecting Cables (P30) After the console has been seated, separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to identify the cables and conne...

42 Assembling and Maintaining TRM 800-Series Treadmills Reassembling the Treadmill Fairing After the console is in place, reattach the two cover panels of the treadmill fairing. Important: In the following procedure, do not allow the fasteners to break or pinch any cables. To reassemble the fairing:...

Installing the Console 43 Verifying That the Heart Rate Display Is Operational To verify that the heart rate display is operational: 1. Begin exercising on the equipment. 2. Grasp both touch-sensitive handlebars. Note: The heart rate is read within ten seconds. During that time, the heart on the dis...

Chapter 3 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklist. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk ...

46 Assembling and Maintaining TRM 800-Series Treadmills Alternatively, you can clean the equipment with Athletix fitness equipment cleaning wipes (for more information, visit www.athletixproducts.com ) CAUTION: Read and follow the manufacturer’s instructions, particularly dilution instructions, befo...

Maintenance 47 Weekly Maintenance Perform the following maintenance tasks every week: 1. Elevate the tread to maximum incline, then turn off the power switch or circuit breaker and unplug the unit from the wall outlet. 2. Clean the floor under the equipment using a vacuum cleaner or a damp mop. 3. W...

48 Assembling and Maintaining TRM 800-Series Treadmills 5. Check the belt tension of the step-up and drive belts. 6. Clean and lubricate the lift motor screw with an approved grease such as SuperLube® with Teflon® or Mobil 1® synthetic grease (adjustable-ramp models only). 7. Check all fasteners for...

Maintenance 49 If the belt tracks off center ... Then loosen ... To the left The right adjusting bolt To the right The left adjusting bolt 3. Recheck the belt position as described under Checking the Alignment of the Running Belt . Note: If slippage occurs, tighten both adjusting bolts evenly until ...

50 Assembling and Maintaining TRM 800-Series Treadmills 6. Observe the belt from the rear of the treadmill for a few minutes. The belt should remain centered along the running bed. If it drifts off center, adjust it. Refer to Treadmill: Adjusting the Running Belt . Important : Failure to align the b...

Chapter 4 Treadmill Safety Features Before allowing users on Precor equipment, review the Important Safety Instructions in this manual. You should also teach your patrons how to use the equipment safely, according to the guidelines on. Entering the Safety Code When the equipment is shipped from the ...

54 Assembling and Maintaining TRM 800-Series Treadmills Using the Treadmill Safety Clip The treadmill is equipped with two different stop functions, which behave as follows: If the user … Then the treadmill belt … And the console … Presses down on the red STOP button Slows to a stop Shows that the e...

Treadmill Safety Features 55 If the restart switch trips during exercise, perform the following steps: 1. Reattach the safety clip if necessary. 2. Press the restart switch down until it clicks, returning it to its normal position. Note: If the restart switch trips, all information about the current...

Chapter 5 Commercial Cardiovascular Equipment Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS. Limited Warranty. Precor Inco...

58 Assembling and Maintaining TRM 800-Series Treadmills Options / Accessories Many options or accessories have components that are connected internally or mounted inside the electronic console. The following guidelines determine the warranty for these components. If the internal components are insta...

60 Assembling and Maintaining TRM 800-Series Treadmills EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES. PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT (INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILITY)...