Precor EFX 835 - Manual

Important Safety Instructions 5  If you plan to move the equipment, obtain help and use proper lifting techniques. Refer to the "Moving the Equipment" section of the assembly and maintenance guide.  Use the equipment only for its intended purpose as described in this manual. Do not use acc...

6 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Hazardous Materials and Proper Disposal The batteries within self-powered equipment contain materials that are considered hazardous to the environment. Federal law requires proper disposal of these batteries. If you plan to...

Important Safety Instructions 7 Radio Frequency Interference (RFI) The RFID module conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to comply with the li...

Important Safety Instructions 9 Radio Frequency Interference (RFI) This Precor exercise equipment conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to com...

Table of Contents Important Safety Instructions ................................................... 3 Safety Precaution s .................................................................................3 Educating Users ..................................................................................

Chapter 1 Assembling the EFX WARNING You will need the assistance of two other people to assemble this unit. DO NOT attempt assembly by yourself . Important: The instructions in the following procedures are described from the perspective of a person standing directly in front of the equipment (that ...

14 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835  Begin installation of all fasteners by hand, then partially tighten them. Do not fully tighten fasteners until instructed to do so. Important : When wrench-tightening the screws, make sure the head of the fastener is par...

Assembling the EFX 15 Fasteners Quantity Buttonhead screws ( ⁵₁₆ –inch x �1 � –inch) � 14 Self-tapping screws ( 1¹₂ -inch) 4 Flat head hex drive screws ( ¹₄ -inch x ³₄ -inch) 4 Bushings 2 Link arm caps 2 Pivot arm caps 2 Pivot axle caps Upright support covers (right-hand and left-hand sets, pack...

16 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Required Tools  #2 Phillips screwdriver  Rubber mallet  SAE standard hex wrench set  SAE standard socket set  Two ⁹₁₆ -inch wrenches (open-end and box-end)  Wire cutter Performing the Assembly DANGER Do not attempt ...

Assembling the EFX 17 Important : Do not stretch, crimp, or damage the cable. Cables damaged by improper installation will not be covered by the Precor Limited Warranty. Figure 3: Thread cable through upright support 3. Attach the left upright support to the base frame using four buttonhead screws, ...

Assembling the EFX 19 9. Attach the cable to the appropriate connector inside the base of the EFX, as shown in the following illustration and table. Figure 6: Cable connection points inside EFX base Connect … To … The console power cable (red and black, individual leads) The power connector on the j...

Assembling the EFX 21 Important: When wrench-tightening the screws, make sure the head of the fastener is parallel to the product surface. If it is not, stop tightening to avoid cross-threading. To avoid further damage, stop assembly work and contact Customer Support. 3. Check alignments and thread ...

22 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 2. Fully tighten the fasteners on the back of each upright support. Figure 11: Tighten the back fasteners on the upright supports 3. Fully tighten the fasteners on the lower sides of each upright support. Figure 12: Tighte...

Assembling the EFX 23 To attach the water bottle holder: 1. Position the water bottle holder as shown in the graphic and attach it to the right stationary handlebar. Figure 14: Water bottle attachment 2. Secure the water bottle holder to the handlebar using three Phillips-head screws. To attach the ...

24 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 2. To attach the upper body handlebars, place one split washer and one ⁵₁₆ -inch washer on each of six socket-head cap screws, then insert three of the screws through each handlebar bracket. Fully tighten the fasteners us...

Assembling the EFX 25 To attach the upright support covers and pivot arm caps: 1. Place one inner and one outer upright support cover around one of the upright supports, aligning them so that the arrows on their inside surfaces point toward the front of the unit. 2. Line up the protrusions on the ou...

26 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 7. Attach the pivot arm caps and seat them with a rubber mallet. Figure 19: Pivot arm cap attachment 8. Insert the two pivot axle caps and press them firmly into place, seating them with a rubber mallet if necessary. Figur...

Assembling the EFX 27 Leveling the EFX Make sure the unit is level before allowing anyone to use it. CAUTION: To eliminate movement, make sure the adjustable feet are in contact with the floor. To level the unit: 1. Gently rock the unit. If there is any movement, ask your assistant to tip the unit t...

28 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Breaking in the Equipment Precor equipment does not require an actual break-in period. However, moving components such as belts, gears, and bearings can settle while the equipment is being stored or shipped. This can cause...

Chapter 2 Installing the Console To make installation easier, all Precor Experience Series consoles use the same mounting hardware and connector locations whenever possible. The installation sequence for any of them is as follows:  Threading the cable assembly  Connecting cables  Completing the i...

30 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Important : Before you begin the following procedure, remove the rear cover from the control console. To remove the cover, use your fingernails to pry the lower edge loose, then swing the cover up and out as shown in the f...

Installing the Console 31 Connecting Cables (P80) After the console has been seated, separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to identify the cables and conne...

32 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Cable Connector Type Circuit Connector Location Heart rate sensors Four-contact strip, keyed Safety key (treadmills only) Six-contact strip, keyed CSAFE Eight-contact modular, on flat gray cable Auto Stop sensor (treadmill...

Installing the Console 33 The following illustration shows how the cable is positioned once it is installed. Figure 25: Connecting the television cable Connecting the Ethernet and Base Unit Data Cables Both the Ethernet and base unit data cables pass through the cutaway opening at the upper right co...

34 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Connecting the Heart Rate Sensor Cable The heart rate sensor cable passes through the cutaway opening at the upper left corner of the back plate, then down to the small circuit board at the lower left of the console. The f...

Installing the Console 35 Completing the Console Installation (P80) Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly. To complete the installat...

38 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Completing the Console Installation (P30) Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cabl...

Chapter 3 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklist. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk ...

40 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Alternatively, you can clean the equipment with Athletix fitness equipment cleaning wipes (for more information, visit www.athletixproducts.com ) CAUTION Vacuum the floor underneath the equipment frequently to prevent the ...

Maintenance 41 Weekly Maintenance Perform the following maintenance tasks every week: 1. Disconnect the external power supply. 2. Clean the ramps and wheels with water or an approved cleaner. 3. Inspect the power cord to verify that it is not pinched under the equipment or between any two moving par...

42 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 5. Check the belt tension of the step-up and drive belts. 6. Clean and lubricate the lift motor screw with an approved grease such as SuperLube® with Teflon® or Mobil 1® synthetic grease (adjustable-ramp models only). 7. C...

Chapter 4 Self-Powered Features Important : This chapter of the manual describes Precor fitness equipment that can operate without being connected to AC power. This includes units equipped with P40 or P20 consoles. However, P80 consoles must be connected to AC power through their power supplies to o...

44 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Informational Displays Prior to Shutdown The equipment saves its battery charge by moving into a shutdown mode. If the user does not maintain the minimum rate of motion, a 30-second shutdown process begins. In this mode, t...

Self-Powered Features 45 Using the Optional Power Adapter After connecting the power adapter to the equipment, plug the opposite end into the appropriate power source (120 V or 240 V). CAUTION: When the optional power adapter is in use, make sure that the power supply cord does not create a safety h...

46 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Replacing the Battery The equipment’s battery is built to last for a long time. However, if you feel that the battery may need replacing, check with an authorized service technician. Refer to Obtaining Service . CAUTION: T...

Chapter 5 Commercial Cardiovascular Equipment Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS. Limited Warranty. Precor Inco...

48 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 Options / Accessories Many options or accessories have components that are connected internally or mounted inside the electronic console. The following guidelines determine the warranty for these components. If the interna...

50 Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 885 / 835 EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES. PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT (INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE...

Assembling and Maintaining Elliptical Fitness Crosstrainers ™ EFX ® 885 • EFX ® 835 Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 EFX 885/835 PAG/OM 300711-301 rev F Warranty #36286-114 14 February 2011

Important Safety Instructions 7 Regulatory Notices for Cardiovascular Exercise Equipment The regulatory information in this section applies to the exercise equipment and its control console. Safety Approvals for Cardiovascular Equipment Precor equipment has been tested and found to comply with the f...

Table of Contents Important Safety Instructions ................................................... 3 Safety Precautions .................................................................................3 Hazardous Materials and Proper Disposal .................................... 6 Product Recycling...

Chapter 2 Getting Started The P30 console offers administrators the ability to set default values that meet their specific needs. These settings include items like language, units of measure, and setting a maximum allowed workout time for each piece of equipment. Activating the Console for Self-Powe...

14 Operating and Maintaining the P30 Console Optional Use of the Power Adapter An optional AC power adapter provides sustained power to the equipment. This adapter allows you to change settings without having to pedal the equipment. To purchase the power adapter, contact your dealer. If you purchase...

Getting Started 15 Identifying Parts of the Console The following diagram provides information about the console keys. The number and actions of the console keys may differ slightly depending on the type of equipment. Figure 3: P30 console keys Table 1. Parts of the console Number Part Name Details ...

Chapter 3 Setting Up the Console Use the System Settings mode to configure settings in a way that benefits your users and your facility. The System Settings menu is visible only to administrators and registered service technicians. Changes made to these settings are saved to the fitness equipment. T...

20 Operating and Maintaining the P30 Console Note: On self-powered equipment, the battery initializes when you begin working out. You must maintain a minimum rate of motion for the Welcome banner to appear. The changes made in System Setting modes become the default settings when the display resets ...

Setting Up the Console 21 Setting Club Parameter Values Use this information to customize the equipment for your setting. Safety Code (Treadmill only) Value Range: Enabled or Disabled (Default: Disabled) When the equipment is shipped from the factory, the safety code protection feature is disabled. ...

22 Operating and Maintaining the P30 Console Set Max Workout Time (All Equipment) Value Range: 1 to 240 minutes (Default: 60 minutes) You can set a maximum workout time per session. Choose a time limit between 1 and 240 minutes, or select No Limit if you do not want to set a time limit. For example,...

Setting Up the Console 23 Creating a Custom Workout Value Range: ON or OFF (Default Value: OFF) Create a customized program for your workout. Note: This option is not available on all equipment. To create a custom program: 1. At the SET CUSTOM PROGRAM prompt, press OK . The program profile appears i...

24 Operating and Maintaining the P30 Console 6. When you have finished creating your program, press OK to save the program profile, and return to the Welcome banner. Press BACK , to exit this setting without saving your changes to the custom profile. Set Speed Limit (Treadmill only) Value Range: Ful...

Setting Up the Console 25 Set Resistance Range (Bike only) Value Range: High, Medium, or Low (Default: High) You can set a low, medium, or high base resistance on the recumbent or upright bikes. There are 25 levels of resistance within each base setting, but the base setting affects the overall resi...

26 Operating and Maintaining the P30 Console Viewing the Informational Displays Information Display settings are values that provide you with information about the equipment. Types of information contained in this setting group include, an event log, software and equipment serial numbers, and usage ...

Setting Up the Console 27 Product Value Information provided All UPPER BASE SW PART NUMBER Upper base application software version All LOWER BASE SW PART NUMBER Lower application software version All METRICS BOARD Software number on the Metrics Board AMT STRIDE DIAL SW PART NUMBER Stride Dial softwa...

Setting Up the Console 29 User ID Entry with CSAFE Equipment This equipment is fully compatible with CSAFE protocols. When the equipment is connected to a CSAFE master device, the user is prompted to press ENTER and begin an identification process. The user ID is displayed as five zeros and indicate...

Chapter 4 Introducing Users to the P30 Console CAUTION: Before beginning any fitness program, see your physician for a thorough physical examination. Seek advice from your physician to learn the target heart rate appropriate for your fitness level. The P30 console offers an easy-to-follow display an...

Introducing Users to the P30 Console 33 Using a Chest Strap Transmitter WARNING Signals used by the heart rate straps may interfere with pacemakers or other implanted devices. Consult your physician and the manufacturers of your heart rate strap and implanted device before using a heart rate strap. ...

34 Operating and Maintaining the P30 Console Using the Treadmill Safety Clip The treadmill is equipped with two different stop functions, which behave as follows: If the user … Then the treadmill belt … And the console … Presses down on the red STOP button Slows to a stop Shows that the exercise wor...

Introducing Users to the P30 Console 35 If the restart switch trips during exercise, perform the following steps: 1. Reattach the safety clip if necessary. 2. Press the restart switch down until it clicks, returning it to its normal position. Note: If the restart switch trips, all information about ...

36 Operating and Maintaining the P30 Console Treadmill Auto Stop™ ( Automatic Stop) Function Important: The default setting for this feature is ON. An administrator can turn off this feature in the System Settings; however, Precor recommends it remain ON. The Auto Stop™ (Automatic Stop) feature is d...

Chapter 5 Starting a Workout CAUTION: If you are using a treadmill, be sure to attach the security clip to your clothing before starting your workout. The equipment is in the Welcome state when the words SELECT A WORKOUT OR PRESS QUICKSTART TO BEGIN scroll across the scrolling upper text display and...

38 Operating and Maintaining the P30 Console Starting a Preset Programmed Workout Preset workouts are a great way to tailor your workouts to your fitness goals, stay challenged, and add variety to your sessions. The P30 includes the following preset programs depending on the type of equipment:  Man...

Starting a Workout 39 To choose a unit of measure before you begin exercising: 1. From the Welcome banner, press OPTIONS . 2. Press OPTIONS twice to go UNITS . 3. Use the Up and Down arrows to select a unit of measure. 4. Once you have selected a unit of measure, press OK . Setting Options after You...

40 Operating and Maintaining the P30 Console Pausing and Resuming an Exercise Session When you interrupt a workout, the equipment responds in one of two ways, depending on how it is powered. Paused (Externally Powered Equipment) When the session is paused, the belt speed is slowly reduced to zero, o...

Starting a Workout 41 Ending a Session Cooling down is an important aspect of your workout because it helps reduce muscle stiffness and soreness by transporting excess lactic acid out of the working muscles. In addition, a three to five minute cool down allows your heart rate to return to its normal...

42 Operating and Maintaining the P30 Console Three different types of metrics are captured during a workout. Controlled Metrics can be set and changed. They include:  Resistance Level (AMT, EFX, bike)  Speed (treadmill)  Incline (treadmill)  Steps/Minute (climber) Current Performance Metrics des...

Starting a Workout 43 Programs Preset workouts are a great way to tailor your workouts to your fitness goals, stay challenged, and add variety to your sessions. Most P30 equipment contains six preset workouts.  Manual  Heart Rate  Interval  Weight Loss  Variety  Performance The one exception i...

44 Operating and Maintaining the P30 Console Weight Loss The workout time is fixed at 28 minutes. The workout consists of four intervals, each lasting eight minutes. You can change the resistance at any time during the work interval. Variety During this workout, resistance and speed vary throughout ...

Chapter 6 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals suggested. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk of electrical shock, alwa...