Precor 903 - Manual

page 7 5. Secure the mounting bracket and clamp by inserting thetwo long screws through the mounting holes. You mayneed to squeeze the ends of the clamp together to installthe screws. See Diagram 3. Tighten the screws into therecessed holes on the mounting plate using the Phillipshead screwdriver. D...

page 8 Diagram 5 9. Attach the C clips around the handrail as shown inDiagram 5. Position the slight protrusion on the C cliparound the reed switch wire and micro-adjustment knobcable. Squeeze the C clips together to close them andsecure the wires in place. 10. With the electronic console successful...

page 9 904 Assembly Procedures To install the 904 electronic console, take the following steps: 1. Remove the handrail clamp from its box. Take the long andshort screws out of the handrail clamp using your fingers ora Phillips head screwdriver. Set the screws aside. 2. Position the handrail clamp ov...

page 10 3. Insert the long screws through the mounting holes onthe clamp. See Diagram 7. You may need to squeezethe ends of the clamp together to install the screws.Tighten the screws using a Phillips head screwdriveruntil the clamp remains securely in place. A gapshould remain between the opposite ...

page 11 7. Position the electronic console over the handrailclamp and plug the connector into the receptacle. SeeDiagram 8. Do not force the connection. The connec-tor is designed to engage in one direction only. A tabon the connector and a slot on the receptacle help youdetermine the proper alignme...

page 12 Installing the Mounting Pads Two adhesive-backed foam pads (one thick and one thin pad)accompany your electronics option package. The thick pad isused as a spacer and you place the reed switch on it. The thinpad is positioned onto the flywheel and becomes the base forthe magnet. CAUTION: Bot...

page 14 5. Remove the paper backing from one side of the thin padand press the pad firmly in place onto the flywheel. SeeDiagram 11. 6. To mount the magnet and reed switch continue with thesteps below, Attaching the Magnet and Reed Switch. Attaching the Magnet and Reed Switch For the electronic cons...

page 16 Diagram 13 5. Remove the paper to expose the adhesive strip that is onthe foam mounting pad. Press the reed switch onto thepad. Be sure that the reed switch is positioned so that thewires are easily routed up the handrail. See Diagram 13. 6. Rotate the flywheel by hand to make sure that the ...

page 18 To hold on one particular feature, press the SELECT buttonwhile the feature (such as TIME) is being displayed. The iconstops blinking. To return to SCAN mode, press the SELECTbutton one more time. The electronic console automatically shuts off when thetreadmill is not in use after approximat...

page 19 PULSE—shows your heartrate if you have attached andare using the ear clip. Refer toChoosing a Target HeartRate. You can also set analarm to indicate when youreach your target heart rate. CALORIES - shows theestimated total number ofcalories burned during yourworkout. Setting the Timer The ti...

page 20 Setting the DISTANCE If you have a specific number of kilometers that you wantto travel during your workout, use this feature. An alarmsounds when you reach the specified distance. To set thedistance, take the following steps: 1. When DISTANCE is displayed, press the SELECTbutton. The icon s...

page 22 Note: The located in the upper left corner of the display begins to blink once a heart rate is detected. 2. When the (PULSE) icon is displayed, press the SELECT button. The icon stops blinking. 3. Press the CLEAR button (“OFF” appears on the display). 4. Press the SET button (“50” appears on...

page 23 Maintaining the Electronic Console Use a damp, clean cloth after every workout to wipe off anyperspiration that might have fallen on the electronic console.Periodically, clean the electronic console using a clothdampened with a mild dishwashing detergent solution. Rinse thesolution off with ...

page 26 Appendix A Put magnet mounting pad here Shaft cut-away Make a copy of this template or trace the pattern onto a different sheet of paper before cutting along the dotted lines.