Precor 835 - Manual

Important Safety Instructions 5  If you plan to move the equipment, obtain help and use proper lifting techniques. refer to the "Moving the Equipment" section of the assembly and maintenance guide.  Use the equipment only for its intended purpose as described in this manual. Do not use acc...

6 Assembling and Maintaining the 835 Climber Hazardous Materials and Proper Disposal The batteries within self-powered equipment contain materials that are considered hazardous to the environment. Federal law requires proper disposal of these batteries. If you plan to dispose of your equipment, cont...

Important Safety Instructions 7 Radio Frequency Interference (RFI) The RFID module conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to comply with the li...

8 Assembling and Maintaining the 835 Climber European Applications CE compliance is claimed to the following directives:  1999/5/EC R&TTE Directive  2006/95/EC LVD Directive  2002/95/EC RoHS Directive Directive compliance has been verified to the following standards:  EN 55022  EN 300 330-1...

10 Assembling and Maintaining the 835 Climber Electrical Recommendations: All Equipment Excluding Treadmills Note : This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. For equipment fitted with a P80 console or Personal Viewing Syst...

Table of Contents Important Safety Instructions ................................................... 3 Safety Precaution s .................................................................................3 Educating Users ..................................................................................

Chapter 1 Assembling the Climber Thank you for choosing Precor. For proper installation, please read this guide thoroughly and follow the assembly instructions. If you do not assemble the climber according to these guidelines, you could void the Precor Limited Warranty. Unpacking the Equipment Ask f...

14 Assembling and Maintaining the 835 Climber Important : When wrench tightening, the head of the fastener should be flush with the product. If it is not, cross-threading has occurred. Do not attempt to rework the assembly as more damage to the equipment will occur. Contact Customer Support. Refer t...

Assembling the Climber 15 Required Tools Before beginning the installation, make sure you have the following tools available:  Wire tie cutter  Phillips screwdriver  One ¹₂ -inch combination wrench (open-end or box-end)  SAE Standard socket set  Standard set of hex keys Assembling the Climber ...

Assembling the Climber 19 12. Slide the rubber grommet onto the plastic top cover, as shown in the following illustration. Apply pressure to snap it into place. Figure 7: Sliding the grommet into place

20 Assembling and Maintaining the 835 Climber Attaching the Handrails Use the following procedure to install the external handrails on the climber. To attach the handrails: 1. Slide a lower handrail boot onto each handrail. Figure 8: Adding the handrail boot 2. Insert the lower handrails onto the ba...

22 Assembling and Maintaining the 835 Climber 8. Clean the foot steps, plastic covers and upright support with a soft cloth or wipe moistened with an appropriate cleaning solution. For more information about which cleaners to use, refer to Daily Cleaning . 9. Level the climber as described in the se...

Chapter 2 Installing the Console To make installation easier, all Precor Experience Series consoles use the same mounting hardware and connector locations whenever possible. The installation sequence for any of them is as follows:  Threading the cable assembly  Connecting cables  Completing the i...

Installing the Console 25 Connecting Cables (P30) After the console has been seated, separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to identify the cables and conne...

26 Assembling and Maintaining the 835 Climber Completing the Console Installation Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly. To complete...

Chapter 3 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklist. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk ...

28 Assembling and Maintaining the 835 Climber Alternatively, you can clean the equipment with Athletix fitness equipment cleaning wipes (for more information, visit www.athletixproducts.com ) CAUTION Vacuum the floor underneath the equipment frequently to prevent the accumulation of dust and dirt th...

Maintenance 29 Moving the Equipment The equipment is very heavy. If you plan to move it to a new location, obtain the help of an adult assistant and use proper lifting techniques. If the equipment includes roller wheels on one end, use the wheels to reduce the load on yourself and your assistant. To...

Chapter 4 Self-Powered Features Important : This chapter of the manual describes Precor fitness equipment that can operate without being connected to AC power. This includes units equipped with P40 or P20 consoles. However, P80 consoles must be connected to AC power through their power supplies to o...

32 Assembling and Maintaining the 835 Climber Informational Displays Prior to Shutdown The equipment saves its battery charge by moving into a shutdown mode. If the user does not maintain the minimum rate of motion, a 30-second shutdown process begins. In this mode, the console displays a countdown ...

Self-Powered Features 33 Using the Optional Power Adapter After connecting the power adapter to the equipment, plug the opposite end into the appropriate power source (120 V or 240 V). CAUTION: When the optional power adapter is in use, make sure that the power supply cord does not create a safety h...

34 Assembling and Maintaining the 835 Climber Replacing the Battery The equipment’s battery is built to last for a long time. However, if you feel that the battery may need replacing, check with an authorized service technician. Refer to Obtaining Service . CAUTION: The battery stored inside the equ...

Chapter 5 Commercial Cardiovascular Equipment Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS. Limited Warranty. Precor Inco...

36 Assembling and Maintaining the 835 Climber Options / Accessories Many options or accessories have components that are connected internally or mounted inside the electronic console. The following guidelines determine the warranty for these components. If the internal components are installed by th...

38 Assembling and Maintaining the 835 Climber EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES. PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT (INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILITY), OR OTHER...

Assembling and Maintaining the 835 Climber Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 CLM PAG/OM 300714-241 rev E Warranty #36286-114 14 February 2011