Powerware UPS 1000 - 2200 - Manual

Powerware UPS 1000 - 2200

Powerware UPS 1000 - 2200 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
Page: / 24

Table of Contents:

  • Page 3 – Table of contents
  • Page 5 – Requesting a Declaration of Conformity
  • Page 6 – Special Symbols
  • Page 7 – The Powerware
  • Page 8 – Installation; Inspecting the Equipment; Plug the EBM cable into the battery connector on the UPS rear panel.
  • Page 9 – UPS Rear Panels; This section shows the rear panels of the Powerware 5125 models.
  • Page 10 – Operation and Configuration; Operating Modes
  • Page 11 – Standby Mode; During Normal mode, the; When all of the bar graph indicators and the; Buck and Double Boost Mode; Double Boost mode as shown in Figure 7.
  • Page 12 – Battery Mode
  • Page 13 – Turning the UPS Off; To turn off the UPS, press and hold the Off; Initiating the Self–Test; NOTE. The batteries must be fully charged to perform the self–test.; The Powerware 5125 is factory-installed with a Single-Port Module.
  • Page 15 – Load Segments; The following figures show the load segments for each UPS.
  • Page 16 – UPS Maintenance; UPS and Battery Care; For full battery life, keep the UPS at an ambient temperature of 25°C .; Storing the UPS and Batteries; When the; Replacing Batteries; WARNING
  • Page 17 – How to Replace Extended Battery Modules; Use the following procedure to replace EBMs:; How to Replace Internal Batteries; CAUTION
  • Page 18 – Use the following procedure to replace internal batteries:; Remove the UPS front panel by pulling the top.
  • Page 19 – Install the new batteries in the reverse order of removal.; Testing New Batteries; Press and hold the
  • Page 20 – Recycling the Used Battery; Troubleshooting; Audible Alarms and UPS Conditions
  • Page 21 – Silencing an Audible Alarm; To silence the alarm for an existing fault, press the
  • Page 23 – Specifications
Loading the manual

UPS 1000 - 2200 VA
User’s Manual

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Table of contents

Powerware 5125 User’s Manual 1000–2200 VA 1019297Revision A Table of contents 1. Introduction ............................................................................................................. 7 2. Installation .................................................................................

Page 5 - Requesting a Declaration of Conformity

Requesting a Declaration of Conformity Units that are labeled with a CE mark comply with the following harmonized standardsand EU directives:• Harmonized Standards: EN 50091-1-1 and EN 50091-2; IEC 950 Second Edition,Amendments A1, A2, A3, and A4 • EU Directives: 73/23/EEC, Council Directive on equi...

Page 6 - Special Symbols

Special Symbols The following are examples of symbols used on the UPS to alert you to importantinformation: RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock ispresent and the associated warning should be observed. CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’smanual f...

Other Powerware Models

All Powerware Other