Powermatic 1791285 - User Manual

Page 2 - IMPORTANT SAFETY INSTRUCTIONS; WARNING – To reduce risk of injury:

2 IMPORTANT SAFETY INSTRUCTIONS WARNING – To reduce risk of injury: 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious i...

Page 4 - Table of Contents

4 Table of Contents IMPORTANT SAFETY INSTRUCTIONS ...................................................................................................... 2 Table of Contents ................................................................................................................................

Page 6 - Features

Page 8 - Voltage conversion

8 4. Place a level upon the machine table, and adjust the screws over the foot pads as necessary. When the machine is level, tighten all four hex nuts against the machine’s base. Unpainted surfaces, such as the work table and fence, have been given a protective coating at the factory. This should be...

Page 10 - Mounting the Fence; Adjustments; Main Belt Tension

10 8. Close blade guard and tighten knurled knob. Mounting the Fence 1. Slide the fence casting onto the end of the guide bar while pulling back the main lock handle (Figure 9). 2. The fence is moved along the guide bar by rotating the handwheel. Use the main lock handle to secure the fence casting ...

Page 12 - Oiler Adjustment; Operation; Feeding Curved Wood

12 Oiler Adjustment 1. Remove plastic cover. 2. Loosen set screw (Figure 17) and rotate knurled dial clockwise to increase oil output; counter-clockwise to decrease oil output. The scale is in cubic centimeters. 3. Retighten set screw, and install plastic cover. Operation 1. Check the oil tank at th...

Page 13 - Maintenance; Optional Accessory; Troubleshooting

13 Maintenance Before doing maintenance on the machine, disconnect it from the electrical supply by pulling out the plug or switching off the main switch! Failure to comply may cause serious injury. Interior of oil tank must be kept clean at all times. The track of caterpillar chain must be kept lub...

Page 15 - Replacement Parts

15 Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve yo...

Page 16 - Infeed Body Assembly – Exploded View

Page 17 - Infeed Body Assembly – Parts List

17 Infeed Body Assembly – Parts List Index No. Part No. Description Size Qty ................. SLR12-300 ............... Cover Assembly (Items 1 thru 7) ......................... .................................... 1 ................. SLR12-100 ............... Gear Box Assembly (Items 1 thru 10, 33...

Page 18 - Arbor Spindle Assembly – Exploded View

Page 19 - Arbor Spindle Assembly – Parts List

19 Arbor Spindle Assembly – Parts List Index No. Part No. Description Size Qty ................. SLR12-200 ............... Arbor Spindle Assembly (Items 1 thru 13) ........... .................................... 1 1 ............... TS-1492041 ............. Hex Cap Screw ...............................

Page 20 - Motor and Drive Unit Assembly – Exploded View

Page 21 - Motor and Drive Unit Assembly – Parts List

21 Motor and Drive Unit Assembly – Parts List Index No. Part No. Description Size Qty 1 ............... SLR12-501 ............... Eye-Bolt ................................................................ .................................... 1 2 ............... TS-2311161 ............. Hex Nut .........

Page 23 - Roller and Frame Assembly – Exploded View

Page 24 - Roller and Frame Assembly – Parts List

24 Roller and Frame Assembly – Parts List Index No. Part No. Description Size Qty ................. SLR12-300 ............... Cover Assembly (Items 1 thru 7) ......................... .................................... 1 1 ............... SLR12-301 ............... Cover w/ Dust Port .................

Page 27 - Parts List: Table and Stand Assembly

27 Parts List: Table and Stand Assembly Index No. Part No. Description Size Qty ............ SLR12-400FAN ........ Fence Complete Assembly (Index 15, 20-24, 26-31, 52-58, 77, 81-84) .. 1 1 ............... SLR12-401 ............... Bracket ................................................................

Page 30 - Electrical Connections – 3 Phase, 230V, 60Hz

Page 31 - Electrical Connections – 3 Phase, 460V, 60Hz

Page 32 - Preventive Maintenance

32 Preventive Maintenance Checklist for Model SLR12 Straight Line Rip Saw [ ] Work area around machine marked off clearly. [ ] Non-skid floor strips in area where operator normally stands. [ ] Inspect entire machine for loose bolts, nuts, screws. Tighten and replace as necessary. [ ] Clean table are...

Page 33 - Warranty and Service

33 Warranty and Service Powermatic warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time p...

Powermatic 1791285 - User Manual

Table of Contents:

Summary

Other Powermatic Table Saws Models