Philips AMW Manual — Free PDF Download

Page 2 - INSTALLATION INSTRUCTIONS; TOOLS AND SUPPLIES; The main power breakers to the unit , including its accessory or

INSTALLATION INSTRUCTIONS TOOLS AND SUPPLIES The following tools are needed for installation. 1. Level2. Hole Saw3. Core bits4. Hammer5. Drill6. Torque wrench7. Adjustable wrench8. Flat head screwdriver9. Philips head screwdriver10. Wire stripper11. Measuring tape12. Ratchet set13. Flaring tools14. ...

Page 3 - SELECTION OF LOCATION; Select a convenient location where:; INDOOR UNIT

SELECTION OF LOCATION Select a convenient location where: INDOOR UNIT ! The cool air can reach every corner of the area to be cooled. ! The unit is away from any direct heat source ! Easy and short routing of the refrigerant and drain pipes to the exterior. ! There are no flammable gas, alkaline or ...

Page 4 - RECOMMENDED HEIGHT AND LENGTH; INSTALLATION METHOD

RECOMMENDED HEIGHT AND LENGTH If the refrigerant piping is longer than the recommended length, or if the height difference between the indoor and outdoor unit is greater than recommended, the capacity will drop and the compressor could malfunction. Select an installation location that is within the ...

Page 5 - MOUNTING INSTALLATION PLATE:

MOUNTING INSTALLATION PLATE: The fan coil can be installed using any of the four methods described below. Determine which is the most suitable method. Position the installation plate on the wall making sure that it is parallel to the ground. This can be done by aligning the marking-off line with a t...

Page 6 - The piping and drain hose are routed straight through; LEFT SIDE HOLE POSITION:; The; MOUNTING FAN COIL UNIT:

INSTALLATION OF FAN COIL: The extended liquid and suction pipes and drain hose are hidden inside a slot at the back of the fan coil. This allows the hole on the wall to be either on the right or left side of the fan coil. RIGHT SIDE HOLE POSITION: The piping and drain hose are routed straight throug...

Page 7 - REFRIGERATION PIPING & DRAINAGE; PREPARATION OF PIPING

REFRIGERATION PIPING & DRAINAGE PREPARATION OF PIPING Fan coil and side discharge condensing units are equipped with flare connections. Improper flaring and brazing may cause refrigerant to leak out of the system. Follow these instructions carefully in preparing the refrigerant piping. ! Ensure ...

Page 8 - There are 3 piping rules:

PIPING INSULATION Liquid and suction lines must be insulated separately. In a cooling only type air conditioner, both pipes become cold during operation. This can cause moisture to condense on the surface of the pipes, resulting in heat loss. PRECAUTIONS WHEN BENDING PIPES ! The air conditioner's pe...

Page 10 - AIR PURGING

AIR PURGING This procedure is used to remove air from inside the piping connecting the indoor and outdoor units, as well as the air inside the indoor unit. If air purging is not carried out, air will beocme mixed into the refrigerant cycle, causing the pressure to rise to abnormally high levels, inc...

Page 12 - ELECTRICAL WIRING; LOCATION OF TERMINAL BLOCK:; EXTERNAL FINISHING OF PIPING

ELECTRICAL WIRING LOCATION OF TERMINAL BLOCK: The terminal block on the indoor unit is located next to the PCB. Cable access is through the back of the unit. For the condensing unit, the terminal block is located behind the control panel. WIRING CONNECTION: ! All wiring and grounding must comply wit...

Page 13 - OPERATING INSTRUCTIONS; PRODUCT DESCRIPTION

OPERATING INSTRUCTIONS OPERATING TIPS: Observe the following points for economical and safe operation: ! Keep the room temperature at a comfortable level. Too much cooling is unhealthy and results in excessive consumption of electricity. A temperature setting of 75°F (24°C) is usually sufficient dur...

Page 15 - REMOTE CONTROL OPERATION; CONTROLS AND INDICATORS

REMOTE CONTROL OPERATION CONTROLS AND INDICATORS Figure below illustrates the various controls and indicators of the LCD wireless remote control. MODEL: AMW 25, 30

Page 17 - OPERATING INSTRUCTIONS; Start air conditioner.; Select the operational mode.

OPERATING INSTRUCTIONS Before operating the unit for the first time, it is necessary to install the batteries in the remote controller. ! Batteries are located at the back of the remote controller (Model AMW25, 30) and at the front of the remote controller (Model AMW45, 60). ! Open the battery holde...

Page 19 - CARE AND MAINTENANCE; Never use the following

CARE AND MAINTENANCE ! The air conditioner requires proper care and maintenance for efficient operation. A periodic inspection and cleaning may be available from your dealer or distributor. Be sure to ask about this service at the time of installation. The user can also perform some of the care and ...

Page 20 - TROUBLE SHOOTING; BEFORE CALLING FOR SERVICE, PLEASE CHECK THE FOLLOWING:; Air conditioner does not operate:

TROUBLE SHOOTING The following are normal and should not be treated as defects. ! Hissing sound, like flow of water from the unit. This is the sound of the refrigerant at the expansion device, which can be heard from time to time depending on the indoor and outdoor ambient conditions. ! The unit doe...

Page 24 - SERVICE NOTES

SERVICE NOTES AITONS' EQUIPMENT INC. Guelph, Ontario www.aitons.com e-mail: [email protected] Printed in Canada 03/03